inspire ZYTH1801-10-OEGLD2-A60-WW-M-C Minta Lighting System Instruction Manual
- June 3, 2024
- iNSPIRE
Table of Contents
inspire ZYTH1801-10-OEGLD2-A60-WW-M-C Minta Lighting System Instruction
Manual
Warning symbols
| Read the instructions
carefully.
---|---
| Safety Class II. This lamp is doubly insulated and may not be wire to a
protective conductor
| Class III light The light uses a very low current
General Safety Instructions
Read this instruction manual thoroughly before using the appliance and save it for future reference and if necessary pass the instruction manual on to a third party.
WARNING: When using electrical appliance, basic safety precautions should always be followed to reduce the risk of fire, electrical shock and personal injury.
General
Keep device out of reach of children and unauthorised persons.
Check if the electrical speciµcations of this luminaire are compatible with
your installation
WARNING: The power supply must be deactivated prior to assembly,
maintenance or cleaning processes. Remove the fuse or switch the fuse to
OFF and secure from reactivation.
WARNNG: Remove the insulating strip from the remote controller before use.
The remote controller contains a button cell battery. Dangerous if
swallowed.
In case of any defective bulbs, plug out this luminaire immediately. Exchange
the defective bulbs with the same type of µlaments .
Do not remove or insert lamps while the chain is connected to the supply.
For indoor and outdoor use.
Do not interconnect parts of this lighting chain with parts of another
manufacturer’s lighting chain. Interconnection shall be made only by the use
of the supplied connectors. Any open ends must be sealed-o before use.
Use only the supplied transformer,ensure the transformer has adequate
ventilation.
This luminaire is not a toy.
This liminaire is not suitable for illumination, but for decoration only.
Do not expose to direct heat,flame,or submerse in water.
Do not connect the chain to the supply while it is in the packing.
Ensure that all lampholders are µtted with a lamp
This product contains a light source of energy e·ciency class < F >.
Electrical safety
WARNING: the external flexible cable or cord of this luminaire cannot be
replaced; if the cord is damaged, the luminaire shall be destroyed.THIS
LIGHTING CHAIN MUST NOT BE USED WITHOUT ALL GASKETS BEING IN PLACE
Specific Safety Rules
Ensure correct polarity of the batteries, this is indicated in the battery
compartment.
Never throw batteries into µre or water The light string can be electrically
connected only by the same type of our brand items and extended to a maximum
of 8 strands. Max 80M/80LEDs for the lighting chain interconnected. When
hanging the lighting chain,needs 10 supporting point for 10 bulbs Due to
changes in our process, the remote control of a Minta Version 1 may not be
compatible with a Minta Version 2 remote control.
Environmental protection
CAUTION!
Electrical products must not be thrown out with domestic waste. They must be taken to a communal collecting point for environmentally friendly disposal in accordance with local regulations. Contact your local authorities or stockist for advice on recycling. The packaging material is recyclable. Dispose of the packaging in an environmentally friendly manner and make it available for the recyclable material collection-service.
**Batteries must be recycled or disposed of properly. Do not dispose of
batteries in regular trash, municipal waste stream or by µre, as batteries may
leak or explode. Do not open, short circuit or mutilate batteries as injury
may occur.
**
Appliance specifications
TECHNICAL CHARACTERISTICS
Rated voltage| 30V
Rated wattage| 3.6W
Ambient Temperature| 25°C
Protection class| Class III
IP number| IP 44
Transformer| ClassII, INPUT:220-240V~50/60Hz OUTPUT: 30V ,200mA
Replacement lamp| 30V Max. 0.6 W.
Maintenance / Cleaning
Disconnect from mains before maintenance or cleaning.
The replaceable LED µlament is fragile and can be easily broken if handled
incorrectly.Ensure that your fingers do not make contact with the lower
section where the Yellow µlaments are µtted. Grip the solid upper section of
the µlament assembly and gently apply a backwards/forward movement with your
µngers whilst pulling downwards to remove. After removing the old µlament
replace with new one by inserting into the socket, as with removal only grip
the solid upper section during installation.
WARNING: The use of any accessory not specified in this manual may present
a risk of personal injury.
Others (Service, Repairing, Guarantee, etc.)
This electric product is in accordance with the relevant safety requirements.
Repairs should only be carried out by qualiµed persons using original spare
parts, otherwise This may result in considerable danger to the user.
Please contact the store which you bought the product for after sale services
if any.
The product is SELV class III lamp with approved class II LED driver.
Made in China 2021
ADEO Services – 135 Rue Sadi Carnot – CS 00001 59790 RONCHIN – France
ТОВ «Леруа Мерлен Україна», вул. Полярна 17а, м. Київ 04201, Україна
Importado e distribuído por LEROY MERLIN CIA BRASILEIRA DE BRICOLAGEM Rua Domingas Galleteri Blotta, 315 – Interlagos – CEP 04455-360 São Paulo – SP – Brazil CNPJ: 01.438.784/0001-05 CALM (Central de Atendimento Leroy Merlin) -4020.5376 (capitais) e 0800.0205376 (demais regiões)
Imported by Adeo South Africa (PTY) LTD T/A Leroy Merlin Leroy Merlin Greenstone Store – Corner Blackrock Street and Stoneridge Drive, Greenstone Park Ext 2, Edenvale, 1610 Johannesburg, Gauteng, South Africa
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>