OASE 2300 GPH Waterfall Pump Instruction Manual
- June 3, 2024
- Oase
Table of Contents
OASE 2300 GPH Waterfall Pump Instruction Manual
Waterfall Pump 1650 / 2300
REMINDER
CALL 1-866-627-3435
BEFORE RETURNING TO STORE.
Information about these operating instructions
Welcome to OASE Living Water. You made a great choice with the purchase of
this product Waterfall Pump 1650 / 2300. Prior to operating the unit, please
read the instructions of use carefully and fully familiarize yourself with the
unit.
Ensure that all work on and with this unit is only carried out in accordance with these instructions. Please strictly follow the enclosed instructions to ensure safe and correct handling of the product. Keep these instructions in a safe place. Please also hand over the instructions when passing the unit on to a new owner.
WARNINGS AND CAUTIONS SYMBOLS
Symbols used in these instructions
The symbols used in this operating manual have the following meanings:
Risk of injury to persons due to dangerous electrical voltage.
This symbol indicates an imminent danger, which can lead to death or severe injuries if the appropriate measures are not taken.
Risk of personal injury caused by a general source of danger.
This symbol indicates an imminent danger, which can lead to death or severe
injuries if the appropriate measures are not taken.
Important! The unit is equipped with a permanent magnet. The magnetic field may affect the function of pacemakers.
Important information for trouble-free operation.
Intended use
Waterfall Pump 1650 / 2300, referred to in the following as “unit”, may only be used as specified in the following:
-
For pumping normal pond water for filters, waterfalls and water courses.
-
Operation under observance of the technical data.
The following restrictions apply to the unit: -
Do not use in swimming pools.
-
CAUTION – this pump has been evaluated for use with water only.
-
Never run the unit without water.
-
Do not use for commercial or industrial purposes.
-
Do not use in conjunction with chemicals, food products, easily flammable or explosive substances.
-
Do not connect to the domestic water supply.
-
Do not exceed the voltage shown on the pump.
-
Inspect the power cord for damage before installation and maintenance.
-
Do not remove the grounding pin from the power cord plug.
Use other than that intended
This unit can be dangerous and cause harm if not used in accordance with these
instructions. Any use not in accordance with these instructions or
modification(s) to the unit will void the limited warranty.
Installation
WARNING
Risk of electric shock – This pump is supplied with a grounding conductor and
grounding-type attachment plug. To reduce the risk of electric shock, be
certain that it is connected only to a properly grounded, grounding-type
receptacle.
Important:
- Always place the unit below water level.
- It is recommened to place the unit horizontally on the ground ensuring its stable position.
- Do not lift the pump by its power cord. Use the handle to lift and maneuver the pump.
Start-up
Attention! The pump must never run dry.
Possible consequences: The pump will be destroyed.
Protective measures: Check the water level at regular intervals. Always place
the unit below water level.
Attention! The installed temperature sensor automatically turns the pump off, if it is overloaded. The pump automatically switches on again once the motor has cooled down. Risk of accident!
Install the unit so that it is not exposed to direct sun radiation (max. 104 ºF – 40 ºC).
Important:
Maintenance and cleaning
Attention! Dangerous electrical voltage.
Possible consequences: Death or serious injuries.
Protective measures:
- Electrical units and installations with a rated voltage of U > 12 V AC or U >30 V DC located in the water: Isolate the units and installations (switch off and disconnect from the power supply) before reaching into the water.
- Isolate the unit before starting any work.
- Secure the unit to prevent unintentional switching on.
WARNING
This pump uses a very strong magnet to achieve superior performance. When
removing the impeller assembly there will be considerable magnetic force
resisting the extraction of the impeller assembly. This is normal. Likewise
when replacing the impeller assembly there will be a strong magnetic force
pulling the assembly into the pump to potentially cause injury to fingers and
in rare cases damaging the ceramic shaft or rear bearing. Use thick gloves
when replacing the impeller assembly.
Cleaning the unit
- Regular cleaning of the pump may be necessary depending upon the environment in which it is operated. Clean the pump when it is visibly soiled or when a drop in performance is detected. Clean the unit with warm water using a soft brush.
- Never use aggressive cleaning agents or chemical solutions. These could attack the housing surface or impair the function.
- In the event of stubborn furring (calcium deposits), a common household cleaner free from vinegar and chlorine can be used. Subsequently, clean the pump thoroughly using warm water.
Cleaning the pump
Storage/Winterization
- Put the unit out of operation at water temperatures below 46 °F (8 °C) or, at the latest, when freezing temperatures are to be expected.
- Thoroughly clean the unit, check for damage.
- Ensure that the storage place is inaccessible to children.
Wear parts
The impeller unit is a wear part and is excluded from the warranty.
Disposal
Do not dispose of this unit with domestic waste! Disable the unit beforehand by cutting off the cables. Further information about the recycling of this product can be obtained from your local municipal authority.
Troubleshooting
OASE North America INC. · www.oase-livingwater.com
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>