L8 Forum Rose Lighting Kinetic Lifting Ball User Manual

June 3, 2024
Rose Lighting

L8 Forum Rose Lighting Kinetic Lifting Ball

Lifting System Brief Manual

Display and Touch Buttons
Press MENU to start setting or returning to the upper option; Press UP/DOWN to browse into the menu options or to adjust the values; Press ENTER to confirm or enter a sub-option.
Operation instructions

Option Sub-option Value Functions
Addr   001-512 To set the DMX address code of the unit
rESt ALL SurE  Strr To reset all functions
FACt P234 To recover the factory settings

ConF

| MOdE| 7CH/8CH| To set the unit in 7CH or 8CH mode
nSiG| Crdt/HdLE| To clear all outputs after 2 seconds (Crdt) or to hold the last DMX value

before the DMX is off (HdLE).






inFO

| ****




CHnL

| 1rEd| CH1 Red dimmer
2Grn| CH2 Green dimmer
3bLU| CH3 Blue dimmer
4diM| CH4 Master dimmer
5FSH| CH5 Strobe
6tiL| CH6 Lifting
7SPd| CH7 Lifting speed, not available in 7CH mode
8CtL| CH8 Control. In 7CH mode, it shows as “7CtL” in CH7.
V101|  | Firmware version
diSP| dMod| ALon/dYoF| To set display always on (ALon) or auto off after 5-second idling (dYoF)
ModE| DMSG| rECE| To set the unit in DMX mode

Note: The functions in grey are for a LED color sphere, which should be purchased separately.

Channel Value Functions
CH1 0 Close
1-255 Red dimmer
CH2 0 Close
1-255 Green dimmer
CH3 0 Close
1-255 Blue
CH4 0-255 Master dimmer


CH5

| 0-9| Disable CH1-CH4
10-19| Enable CH1-CH4
20-209| Strobe, slow  fast, enable CH1-CH4
210-255| Enable CH1-CH4
CH6| 0| When CH8=0, the cord wheel will keep locked.
1-255| Lifting from top to bottom
CH7*| 0-255| Lifting speed, fast  slow (Unavailable in 7CH mode)
CH8**| 0| When CH6=0, the cord wheel will keep locked.

  • The speed channel is unavailable in 7CH mode; The unlock/reset channel will be the 7th channel in 7CH mode.
    Note:** The function channels in grey are for a LED color sphere, which should be purchased separately.

IMPORTANT!!!
Please DO NOT run the machine before the payload is properly applied! If the hoist is powered off in a DMX mode, you must set both CH6 and CH8 (8CH mode) or both CH6 and CH7 (7CH mode) to 0 on the connected DMX controller before turning on the power of the hoist again; After power on again, the unit needs to be reset twice: Once when power is on; another reset at CH8=(240-245) (8CH mode) or CH7=(240-245) (7CH mode). Otherwise, the hoist may run in error.
Warnings: Please keep sufficient safety distance and lifting distance in installation

Step 1: Attach the clamp to the hoist| Step 2: Hang the hoist on the truss, fasten the clamp and correctly use the safety rope| Step 3: Attach the LED color sphere to the hoist
---|---|---

| |


Cautions: Do not run the hoist without any payload being applied.
The lifting cord is inside the hoist when in package. When you take out the hoist, the LED color sphere must be hung to the hoist BEFORE you power on the hoist. Running the hoist without any payload is prohibited, because the lifting cord may be entangled inside the cordwheel and cause error.

  • Step 1: Once the payload is applied, power on the hoist. The hoist will start resetting.

  • Step 2: Connect a DMX console to test the hoist.

  • Step 3: Connect the hoists to a DMX console and reset them again by DMX: Move 8CH to 240~245. If any of the hoists do not reset, check the DMX connections.

  • Step 4: Move 8CH to outside 240-245; Otherwise, the unit will keep the time. Make sure that all the hoists are reset correctly and the balls the correct position. Then, you can start operate the fixtures. Please mind when programming a chase.

Tips:

  • The dimmer channels (1CH-4CH) shall be enabled by 5CH;
  • The strobe effects (5CH) will only be seen when the light is the dimmer channels (1CH-4CH).
  • 6CH is for lifting up and down. Fade in and fade out (slope) is not applicable to this channel.
    Please take into account the lifting up/down time when programming a chase. If a new chase step is made before the lifting up/down is completed in a previous step, error may occur and/or noise may be heard.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals