Rose Lighting 12V400W LED Waterproof Power Supply Owner’s Manual
- June 9, 2024
- Rose Lighting
Table of Contents
Rose Lighting 12V400W LED Waterproof Power Supply
LED Waterproof Power Supply (C&V)
- Protections: short circuit/overload/over voltage/over temperature
- IP67 design for indoor or outdoor installation
- It can be used in dry, wet and rainy environments
- Cooling by free air, high reliability
- 100% full load burn-in test
- Suitable for internal lights application for I /I/I
- Widely used in LED lighting and IT equipment
- Compliance with worldwide safety regulations for led lighting.
Specification
| 12V400W | 24V400W |
|---|
| Output voltage| 12VDC| 24VDC
Output voltage range| 12VDC±0.5VDC| 24VDC±0.5VDC
Output сurrent| Max 33.4A| Max 16.7A
Output power| Max 400W
Output power range| 0~400W
Ripple & Noise| ≤120mV| ≤240mV
Linear Regulation| ±1%
Load Regulation| ±1%
Start-up Time (Typ)| 450ms/230VAC 500ms/115VAC
Hold Up Time(Typ)| 200ms/230VAC 200ms/115VAC
| Input voltage| 175-264Vac or 100-130Vac
Frequency| 50/60Hz
Input сurrent| 3.3A/230Vac or 5.8A/115Vac
Power factor| PF>0.6
No-load power consumption| ＜3W
Efficiency (typ.)| 91%| 90%
Inrush current(typ.)| Cold start 70A at 230Vac
Control surge capability| L,N:2KV L,N-PE:4KV
Leakage сurrent| Max. 0.5mA
| Working temperature| ta: -30°C~ 50°C tc: 80°C
Working humidity| 20 ~ 99%RH, condensing(Waterproof)
Storage temp., humidity| -40°C ~ 80°C, 10~95%RH
| Overtemperature| Protection type: Turn off the output voltage, after the
temperature drops, re-energize to restore.
Over load protection| Shut down the output when current load ≥110%~150%, auto
recovers.
Short circuit protection| Protection type: It can be automatically restored
after the fault is eliminated.
| Withstand voltage| I/P-O/P:3750Vac
Isolation resistance| I/P-O/P: 100MΩ/500VDC/25°C/70%RH
Safety standards| IEC/EN61347;IEC/EN60950;IP67
EMC Test Standards
| EN55015: 2013;EN61547: 2009; EN61000-3-2:2014; EN61000-3-3:2013
Reliability and Quality Control| Impact aging| 100% of the product is fully
loaded and impacted for 4 hours under an environment of at least 40°C±5°C
Component derating| Under the steady-state conditions of rated input and
output, the stress of components will not exceed its maximum nominal value
NO T E
| 1. All parameters not specifically mentioned are measured at 230VAC input, rated load and 25°C ambient temperature.
2. Ripple and noise test method: connect 0.1uF and 47uF capacitors in parallel at the terminal, and measure under 20MHZ bandwidth.
3. Ensure that the power supply is used under the rated parameters and environment.
Dimensions
Relationship diagrams
Packaging Information
DIMENSION|
260x102x37mm(LxWxH)
---|---
PACKING| 305x122x52mm(LxWxH)
CARTON QUANTITY
| 10PCS
CARTON SIZE| 565x320x145mm(LxWxH)
WEIGHT| 1750g±10g/PCS
No further notice if any changes in the manual. Product function depends on
the goods. Please feel free to contact your supplier if any questions.
