NICOR DLR56v5 System LED Downlight System Installation Guide

NICOR DLR56v5 System LED Downlight System

What’s In The Box

Tools Needed
The DLR Recessed Frame requires very few tools for installation. A drill or screwdriver, a pair of wire cutters, and a hammer will help with installation .

Installing the DLRv5 Frame

1. Carefully unpack the frame from its packaging. Inspect product for defects due to shipping.

2. If necessary, adjust hangar bar length by separating bars, snapping to length at score marks, and reassembling.

3. Position frame between joists, ensuring hangar bars are in the correct position. Bottom edge of hangar bars should be level with the bottom of the joists.
   Starting with the swivel foot end of the hangar bar, Secure the hangar bars to the joists with the captive nails provided.

4. Lift and secure opposite side of frame to ceiling joist. Position frame in desired place on hangar bars and tighten set screw to lock frame in place.

5. Connect building power to the frame junction box. Connect black to black and white to white using the provided quick connectors. Connect the bare copper wire to the ground wire of the power source.

Installing the DLR56v5 Downlight into the DLRS6VS Frame

1. Carefully unpack the downlight from its packaging. Inspect product for defects due to shipping.
2. If using optional colored trim, align trim onto downlight and secure by bending over tabs.
3. Join the DLR’s female quick connector to the Frames male quick connector.
4. Align the tabs of the frame cap to the depressions on the DLR and snap the cap in place, making sure no wiring is pinched.
5. Squeeze torsion springs together and install into torsion spring brackets inside the framne.
6. arefuly push the downlight upwards making sure it is flush to the ceiling surface.

View of properly installed downlight system

EXPRESS LIMITED WARRANTY

Subject to the exclusions below, each NICORLED product, including the LED electronics and components of a property installed NICOR LED product, will be free from defect in materials and workmanship for a period of ve (5) years
Trom the original date of purchase. Ihe product shall be considered defective only ir 10% or more of the products LED components tail. NICOR LED Product warranty covers the following performance criteria: LED Light Output will
be maintained above /06 of initial output LED COlor temperature will not shift more than 200K in CC;LED driver will operate Within NICOR specications; and the xture nish, excluding natural aluminum or brass products, wll not
exhibit cracking, peeling, excessive fading, or corrosion during the warranty period. Exceptions apply as dened in NICOR’S product specication sheets, which are incorporated by reference herein.
This limited warranty is provided to you, the purchaser of the product identied on Seller’s invoice, as your exclusive remedy and applies only to NICOR products that have been purchased from an authorized NICOR DIstributor; the
product was new and in an unopened NICOR package at the time of installation; and the NICOR product was installed by a licensed electrician or under the supervision ofa licensed electrician and used by consumers in the United
States or Canada when accompanied with this warranty. This warranty extends only to the rst consumer purchaser and is not transferable. A consumer wishing to invoke the terms of this limited warranty must rst obtain a RGA
number within 30 days of discovery of the defect, and return the product to NIcOR for inspection. Once veried to be covered by this limited warranty, NICOR will, at its sole discretion, repair, replace, or refund the purchase price of
any product that does not conform to this limited warranty. If NICOR, at its sole discretion, determines that the product should be repaired or replaced, this warranty is limited to the reasonable, customary, and necessary costs and
expenses associated with the repair/replacement. This warranty requires that all repair/replacement estimates and costs, including but not limited to equipment rental (if any), and any other cost or expense to be incurred in the
repair/replacement of the product, be approved in advance and in writing by NICOR. FAILURE TO OBTAIN NICOR’S ADVANCE WRITTEN APPROVAL OF ALL REPAIR/REPLACEMENT COSTS AND EXPENSES IN WRITING SHALL VOID THIS

LIMITED WARRANTY.

• Defects or damages resulting Trom improper installation, operation, storage, misuse or abuse, accident, or neglect
• Defects or damages resulting from improper service, testing, adjustment, installation, maintenance, alteration, connection to out-of-specication electrical service, corrosive or damp environments, or connection to incompatible equipment or devices (e.9. connecting non-dimmable lighting products to dimmers);
• Damage which occurs in transit;
• Power surges or overheating due to external conditions
• Acts of nature including but not limited to lightning strikes

ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED TO THE DURATIONOF THIS LIMITED WARRANTY OTHERWISE THE REPAIR. REPLACEMENT. .
EQUENTIAL DAMAGES OF ANY KIND, OR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS OROTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE ABILITY OR INABILITY TO USE THE PRODUCT TO THE FULL EXTENT THESE DAMAGES MAY BE DISCLAIMED BY LAW.

www.nicorlighting.com/support/survey

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>