SUNFREE AC801 WiFi Bridge User Guide
- June 3, 2024
- SUNFREE
Table of Contents
SUNFREE AC801 WiFi Bridge
The Guide
The New WI-FI Bridge Has Not Been Debugged. Please Read This Manual Carefully and Operate According To The Steps.
- Download app (please refer to p4)
- Pairing of mobile phone and Wi-Fi bridge (please refer to p4-p7)
- The Wi-Fi bridge is connected to the smart curtain (please refer to p7-p10)
- Smart curtain setting (please refer to p10-p12)
- Smart speaker control (refer to p15)
Common Problem
-
The Wi-Fi bridge does not respond when paired with the mobile phone Please ensure that the Wi-Fi bridge is in the red light flashing state. If the red light does not flash, long press the matching button just push the button for 5 seconds.
-
The curtain runs in the opposite direction
Refer to p13 “motor steering” -
After the curtain runs, the opening and closing position needs to be adjusted
Refer to p13 “travel setting” -
The curtains didn’t respond
First, confirm whether the wifi bridge is powered on and whether the mobile phone is paired with the wifi bridge (refer to p4-7);
Secondly, confirm whether the motor is powered on and whether the lithium battery is dead (refer to p1);
Finally, confirm whether the intelligent curtain is connected to the wifi bridge (refer to p12).
Wifi Bridge
Wifi Bridge Parameters
Match The Wifi Bridge
-
Smartphone connection 2.4G WIFI
Download App And Register Your Account -
The Wi-Fi Bridge Enters Matching Mode
Match the Wifi Bridge
-
Open the app and click “Add device” or the sign in the Upper right corner
-
Slide the option on the left, select “Others”, and then click “Others Wi-Fi” on the right
-
Keep the phone connected with wifi, enter the wifi password and click “Next” (Operate according to the guidance)
-
Click“Blink Quickly”
-
The Wi-Fi bridge keeps the red Light flashing, and the mobile phone Automatically scans and adds devices.
If the connection times out, please repeat The steps and press the matching button at The end of the wifi bridge for 5 seconds. -
After adding successfully the WI-FI bridge name is “Wi-Fi bridge” and Click “Done” to exit the interface.
Match Smart Blinds
Enter the WIFI bridge control interface “Add sub device” Roller blinds
motor
Press and hold the “m” key of the curtain motor for 2 seconds until the motor
rotates back and forth once to enter the 60 second pairing state Smart
curtain motor
Long press the “m” key of curtain motor for 2 seconds, and the motor flashes
once to enter the 60 second pairing state Wait for a moment, and the Searched
device will be displayed On the interface. Click “Done”
Wifi bridge can add up to 30 devices, which can be paired in this Step at the same time or added one by one in the later stage.
Smart Blinds Setting
app
In the app interface “Home”, click the corresponding Smart curtain to enter the curtain control interface
Control Interface
- Select The Corresponding Curtain Type
- Modify curtain name
- Set up
- Drag to control curtain opening and closing
- Open the curtains
- Stop
- Close the curtains
- Run to the third travel point
Please Control The Curtain After The Curtain Type And Travel Are Set
Click 1 Select The Corresponding Curtain Type
Click 3 Enter The Setting Interface
Smart Blinds Setting Signal strength
Displays the signal strength of the WI-FI Bridge currently connected
Battery Power
Displays the current battery level
Motor Reversing
Change the rotation direction of the motor
Status Light
On / off status indicator (available for some models)
Setting Limits
- Set the position when the curtain is fully open;
- Set the position when the curtain is fully closed;
- Custom curtain position (third),
You can run to this position with one key.
Timer Opera
Add timing function to automatically open / close the curtain
After Setting, Return To The Control Interface
Intelligent Speaker
At present, it supports TM, MI,
Amazon Alexa and Google Assistant platforms
In the app interface “Me”, click the corresponding Smart speaker and connect the third-party Smart speaker according to the prompt
FCC Caution:
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception,which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>