inwa MZ-200A RGB Garden Light Wireless Speaker User Manual

June 3, 2024
inwa

MZ-200A RGB Garden Light Wireless Speaker
User Manual

User’s manual
MZ-200A RGB

01 Quick start guide

Packing list

Product parameter

  • Output power: 4Ω 20W
  • Distortion: ≤1%
  • Frequency response: 20Hz-20KHz
  • Signal to noise ratio: ≥85dB
  • Working time: 60% volume of continuous playback for 4-8 hours/continuous lighting for more than 4-8 hours
  • Input voltage: DC5V/2A
  • Bluetooth version: 5.0
  • Auxiliary input: 3.5mm
  • Wireless distance: 15m Max
  • Battery capacity: 7.4V 2*2600mAh
  • Standby time: ≥300h
  • Waterproof rating: IPX5
  • Charging time: 2-4 hours
  • Distance: The serial transmission distance is  greater than 30 meters
  • Operating temperature range: 0°-40°
  • Working humidity range: 40-50%RH
  • Storage temperature range: -25°C-70°
  • Product net weight: 1380g(including battery)
  • Product size: W182×D182×H268mm

Function panel

  1. Network key/synchronization
  2. Light color switch/off
  3. Volume reduction
  4. Volume up
  5. Power on/off
  6. Charging/Bluetooth/ Networking indicator
  7. 3.5MM audio jack
  8. Type-C jack
  9. LED RGB light

Speaker charging

Note: The speaker must be fully charged before use.

  1. Open the rubber cover, and then insert the power adapter into the charging socket.
  2. Plug the power adapter into the power socket.
  3. When charging, the red indicator light is on; when the red indicator light is off, it is fully charged.(It takes about 2-4 hours to fully charge)

When the red indicator light flashes quickly,the speaker needs to be charged (The low flashing light is only on when the speaker is working)| When the red indicator light is on,The speaker is charging| When the red indicator light goes out,the speaker is fully charged

Bluetooth pairing

(The speaker must be powered on)
A. Establish a new connection

  1. After double-clicking the networking button “ ” , the Bluetooth indicator flashes quickly to enter the pairing state.
  2. Open the Bluetooth device search list of available devices, click to select “MZ-200A” to connect.
  3. After the pairing is successful, the blue indicator light will remain on and a beep will be heard.

When the Bluetooth indicator flashes quickly, the speaker is
ready for pairing| After the pairing is successful, the Bluetooth indicator light will stay on

B. Disconnect current connection and pair with new device

  1. After the devices are paired successfully, double-click the networking button “ ” to enter the re-pairing state.
  2. Repeat steps 1-3 in the previous section (to establish a new pairing).

C. Wake up Bluetooth from sleep mode
To save power, if your device is out of the Bluetooth range (10m/ 393.70in) for more than 5 minutes, the Bluetooth connection will automatically enter sleep mode. To  reconnect when the device is back in range, press the power key “ **” to cancel the sleep mode and re-establish the pairing connection.
Note:** When pairing, the Bluetooth device and the speaker should be close (10m/ 393.70in).
If you cannot pair the device, you may have paired another device with the speaker.
Please follow the steps in B (disconnect and pair with the new device) above to disconnect the possible connection. If it is still difficult to pair the device, please contact customer service.

Synchronous speakers

Note: The synchronization is only valid when you have 2 or more Bluetooth speakers.
(If you have not synchronized any speakers, please refer to the “Bluetooth Pairing” above), the synchronized speakers need to be synchronized before connecting to the Bluetooth device.

  1. First turn on a speaker. (TX main speaker)
  2. Turn on the remaining speakers. (RX receiver)
  3. Press the sync button ” ” on the first speaker for 2 seconds, until the yellow/green two-color indicator light starts to flash alternately.
  4. Press the sync button “ ” on the remaining speakers for 2 seconds until the yellow/ green two-color indicator lights start to flash alternately.
  5. After the machine is connected, the TX main speaker keeps green light, and the RX receiver keeps yellow light, indicating that the pairing is successful.

Note: Be sure to turn off the speakers first and then turn them on again.
If you have any difficulties synchronizing speakers, please refer to the “Sync Tips” below.

Synchronization tips

Please read the following tips to enhance your multi-sync experience!

  1. During the setting process, the synchronization signal is only transmitted for 90 seconds.
    If you do not complete steps 1-4 within 90 seconds, the speaker you are trying to synchronize with will not be synchronized after 90 seconds. If you need more than 90 seconds to complete the synchronization process, just press the sync button ” ” on the first speaker again to reactivate the sync signal (Step 4: Synchronize the speakers in the previous section), and then continue Synchronize more speakers.

  2. When turning on the sync speaker, first turn on the TX main speaker.
    When you sync the speakers, they stay in sync. Even if you turn off the power of the synchronized speakers, they will automatically synchronize again after the power is  turned on. So you should turn on the TX main speaker first.

  3. Select the location of the main speaker.
    When you turn off the power of the TX main speaker (the first speaker), the resynchronized RX receiver will also be turned off.
    Therefore, please place the TX main speaker in a convenient location so that you can easily turn it on and off.

AUX input

The speaker comes with a 3.5mm audio cable, you can use the speaker without Bluetooth.
In this case, Bluetooth will be disabled, but the speaker synchronization function can still be used normally.

  1. Insert one end of the audio cable into the speaker AUX interface.
  2. Insert the other end of the audio cable into the audio jack of the device. (Ensure that the audio jack is not blocked by any protective sleeves or accessories)
  3. After inserting the audio cable into the speaker, you will hear a beep and the red indicator light will light up.

Note: In case of a crash and unable to operate, please use a small screwdriver smaller than 3mm and longer than 30mm to poke the bottom of the AUX jack and press the button. The whole machine will be powered off and reset.

Light display

Note: The gradual color change function is only effective when playing music.
Light display color selection
The light function must be turned on to change the light display color, single press ” ” in order to red, dark blue, light blue,amber, green, pink, purple, white, gradual change color cycle. Note: The default is to automatically change the color of the flashing light when it is turned on. When the Bluetooth is not connected, the light is defaulted to automatically turn off the light at regular 2H.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals