Inwa MZ-200K Wireless Karaoke Speaker User Manual

June 16, 2024
inwa

Wireless Karaoke Speaker
MZ-200K RGB
User’s Manual

Quick start guide

  1. Packing list
  2. Product parameter
    PMPO power: 40W
    Distortion: <1%
    Frequency response: 20Hz-20KHz
    Signal to noise ratio : ≥85dB
    Input voltage: DC 5V/2.5A
    Bluetooth version: 5.2
    Wireless distance: ≥49ft/15m
    Working time: 60% volume can last for 4 hours in LED rhythm mode
    Auxiliary input: 3.5mm
    Battery capacity: 7.4V 2600mAh
    Standby time: ≥300h
    Charging time : 2-4 hours
    Operating temperature range: 0°-40°
    Working humidity range: 40-50%RH
    Storage temperature range: -25°C-70°
    Product size: W182×D182×H268mm(Speaker) W230×D47×H47mm(Microphone)

Instructions

  1. Function panel 1. Pairing/Mode Key
    4. Volume up/Next
    7. 3.5MM audio jack
    2. Light color ON/OFF
    5. Power on/off key
    8. Type-C jack
    3. Volume down/Prev
    6. Charging/BT/MIC/USB indicator light
    9. LED RGB light 1. Display screen: Display power, signal, frequency band, and frequency
    2. Power switch:
    Press and hold for 2 seconds to turn on/off, Short press for frequency band mode
    3. Battery compartment
    4. Frequency modulation composite key
    5. Volume up
    6. Volume down

  2. Speaker charging
    Note: The speaker must be fully charged before use.
    1. Open the rubber cover, and then insert the power cable into charging port.
    2. Plug the power adapter into the power socket.
    3. When charging, the red indicator light remains on for a long time, and when the red indicator light goes out, it is fully charged.

  3. Microphone battery replacement Note: If the microphone is turned on and not used within 20 minutes, it will automatically shut down.
    1. When the microphone power is low, the power border in the microphone display window continues to flash. At this time, the microphone battery needs to be replaced.
    2. The microphone power level is displayed above the power button, with a total of 3 battery cells, each with approximately 33% power.
    3. When not in use for a long time, it is recommended to remove the microphone battery to prevent battery leakage and corrosion of internal components.

  4. Turn on the microphone
    On first use out of the box, the microphone and speaker are auto-connect on startup. To activate or deactivate the microphone mode, simply double-click the speaker’s pairing key ” ” : Turn on the speaker and microphone by a prolonged press of the ” ” key for 2 seconds. Then, double-click the ” ” key on the speaker to activate the pairing mode. If the yellow indicator light remains lit, it indicates a successful connection between the speaker and the microphone.

  5. Microphone display screen introduction 1. Battery display: displays the remaining battery level of the microphone battery
    2. Channel display: Display the current working channel of the microphone
    3. Signal display: Display the current working signal of the microphone
    4. Sound mode: EF 0 represents KTV, EF1 represents mute on, and EF 2 represents host
    5. Frequency display: Display the current working frequency of the microphone, with numerical values showing CH01 to CH20
    6. Volume display: Display the current working volume of the microphone, with numerical values displaying U-01 to U-04

  6. Microphone FM
    1. The microphone has a total of 20 frequencies: CH01-CH020.
    2. After successfully pairing the microphone with the speaker, briefly press the FM composite key ” ” once, and the frequency number on the microphone display screen will jump to the next digital frequency and have a corresponding channel display.

  7. Bluetooth pairing
    A. Establishing a new connection
    1. Turn on the speaker by a prolonged press of the ” ” key for 2 seconds. The default volume is 60%, and the Bluetooth indicator light quickly flashes to enter pairing mode.
    2. Open the Bluetooth device search list for available devices, click and select “MZ-200K” to connect.
    3. After successful pairing, the blue indicator light will remain permanently on and a prompt tone will be heard. B. Disconnect the current connection and pair with a new device
    1. After the device is successfully paired, press and hold the pairing key ” ” for 2 seconds to enter the re pairing state.
    2. Repeat steps 2-3 from the previous section (establish a new connection).
    C. Bluetooth connection precautions
    When your device exceeds the Bluetooth range (10m/393.70in), it may not be possible to connect to the speaker. Bluetooth connection should be used within the device coverage range.

  8. AUX input
    The speaker comes with a 3.5mm audio cable, which you can use to listen to music.
    1. Insert one end of the audio cable into the AUX interface of the speaker.
    2. Insert the other end of the audio cable into the audio jack of the device.
    3. Short press the mode key ” ” to switch to AUX input mode, and the red indicator light will light up.

  9. Language mode
    In Bluetooth mode, press and hold the ” ” key for 5 seconds to switch to Chinese and English mode.

  10. Record mode
    Press and hold the speaker power key ” ” for 2 seconds, and then connect the phone/PC with a USB data cable. The yellow indicator light on the speaker will stay on and automatically switch to sound card mode. At this time, the microphone sound can be recorded.

  11. Light display
    Light Color Selection
    To change the color of the light display, ensure that the lighting function is turned on. The default light mode upon powering on is pulsating flashing lights. Simply press “ ” to switch in sequence: rhythmic flashing light → colorful running light circle → white light RGB mixed color → yellow → dark blue → green → purple → red → pink. Long press or double-click ” ” in any light to turn off the light. Note:
    The default mode for turning on is the light mode, with a rhythmic flashing light. (25% brightness without music, gradient color switching, 25-100% brightness flashing with music)

  12. Support information
    Need further help, you can contact us by
    A. Service E-mail: inwa_support@innosystemtech.com
    B. Or contact us on Amazon
    1. Go to Your Orders.
    2. Find your order in the list.
    3. Select Problem with order.
    4. Choose your topic from list displayed. Select Contact seller.

GOAL REACH CONSULTING LTD
OFFICE 1029 3 HARDMAN STREET 10TH
FLOOR, SPINNINGFIELDS MANCHESTER,
UK M3 3HF
OST UK 20230424000006 goalservice@hotmail.com
We simply act as UK representative for cross-border sellers, and are not manufacturers/
importers/distributors for the product, nor involved in the manufacture/import/sale of the
product. Therefore, we are not responsible for any after-sales services related to the
product. ln case of any product quality or infringement issues, the manufacturer/importer/
seller shall be solely held responsible.
SUCCESS COURIER SL
CALLE RIO TORMES NUM.1, PLANTA 1,
DERECHA , OFICINA 3, Fuenlabrada,
Madrid,28947 Spain
OST_EU_20230424000022 successservice2@hotmail.com
We simply act as EU representative for cross-border sellers, and are not manufacturers/
importers/distributors for the product, nor involved in the manufacture/import/sale of the
product. Therefore, we are not responsible for any after-sales services related to the
product. ln case of any product quality or infringement issues, the manufacturer/importer/
seller shall be solely held responsible.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals