SAMSUNG SKK-8MC 27-Inch Front Load Washer and Dryer Instruction Manual
- June 3, 2024
- Samsung
Table of Contents
SKK-8MC 27-Inch Front Load Washer and Dryer
Instruction Manual
SKK-8MC 27-Inch Front Load Washer and Dryer
STACKING+MULTI CONTROL KIT INSTALLATION INSTRUCTIONS (WASHER & DRYER
ONLY)
CONSIGNES D’INSTALLATION DU KIT MULTI-CONTRÔLE ET DU KIT DE SUPERPOSITION
**CAUTION : Two people are required to lift the dryer on to the washer.
WARNING : These washer and dryer are not suitable for mobile home or RV
installation.
Dryer
STEP 1 Have two persons place the dryer on a non-slippery floor. Then,
have one person tilt the dryer to the side. Do not lay the dryer down. The
dryer may be scratched.
STEP 2 Check to make sure the legs are all the way up and tightened
securely in place. And then insert the stacking support guides in the
rectangular holes of the dryer’s base until you hear a clicking sound. You
don’t need to remove the legs.
STEP 3** Repeat the same step above on the other side.
STEP 4 Bottom view of the dryer after assembling the Stacking Support Guides to the dryer base.
- Use a stacking-kit compatible with the purchased model.
- Do not lay the dryer down on a floor when installing the stacking kit. Hold the dryer firmly to prevent it from tipping over.
Washer (only applicable for models supporting multi-control)
STEP 5 DO NOT TIGHTEN SCREWS COMPLETELY.
LOOSELY fasten two REAR BRACKETS at the back of the washer using the two
SCREWS-HEX HEAD (6002-001431) and WASHERS (DC60-00044A).
- Fasten the ASSY BRACKET STACKING on the right-side.
- Fasten the other REAR BRACKET on the left-side.
STEP 6 Lift and position dryer into the position on the washer shown
above, slide dryer backwards to make contact with rear brackets.
CAUTION : To prevent noise, check the followings.
- Make sure the washer is level.
- Make sure the dryer’s leveling legs are tightened up.
STEP 7 Align rear brackets with mounting holes on the rear of dryer as
shown above.
STEP 8 LOOSELY assemble rear
brackets to the back of the dryer using two (2) Screws- Phillips Pan Head
(6006-001174) for each rear bracket as shown above.
Extra screws may be included with this kit.
STEP 9 Tighten screws on the dryer side of the rear bracket.
WARNING : Additional gas hook-up components are required for
gas dryer.
STEP 10 Tighten screws on the washer side of the rear bracket.
* DO NOT REVERSE THE ORDER OF STEPS 8 & 9.
STEP 11 Assemble the provided ASSY BRACKET STACKING on the right side and
assemble the REAR BRACKET on the left side. All the necessary parts are
included in the stacking kit.
STEP 12 Open the connector port cover on the dryer and the washer, connect the wire on both ports, and then close the cover.
- Be careful not to damage the wire by the connector port cover.
- Do not pull the wire too hard to remove the connector from the port.
STEP 13 There are two HOLDER WIRE preassembled to the wire. Attach each
HOLDER WIRE to the dryer and the washer. Check and make sure the washer and
the
dryer are connected.
Stacking kit components
Stacking Support Guides (2)
– DC61-04159A
Stacking Support Guides (2)
– DC61-01480B| Rear Bracket (1)
(All models other than the ones using
DC61-04160A parts)
– DC61-04955A| Screw-Hex Head (4)
– 6009-001476 (M5, L10)
– 6002-001431 (M5, L16)
Screw Phillips-Pan Head (8)
– 6006-001174 (M4, L12)| Washer (4)
– DC60-00044A (ID5, OD10)| Assy Bracket Stacking (1)
DC68-04334A-00
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>