SELVE i-R Send 1 Radio Hand Transmitter Instruction Manual

June 3, 2024
SELVE

i-R Send 1
i-R Send 5
i-R Wall Send
Basic
Operating Instructions

i-R Send 1 Radio Hand Transmitter

Please keep these instructions in a safe place!

Technical data

SELVE i-R Send 1 Radio Hand Transmitter - Set intermediate position
6 Subject to technical modifications.
General conformity declaration The company SELVE GmbH & CO. KG, hereby declares that the i-R Send 1/i-R Send 5/i-R Wall Send/i-R Wall Send Basic is in conformity
with the basic requirements and other relevant provisions of the Directive 1999/5/EC. The declaration of conformity can be seen at www.selve.de.

SELVE i-R Send 1 Radio Hand Transmitter

i-R Send 1/i-R Send 5
Explanation of displays and buttons

  1. UP button,
  2. STOP button,
  3. DOWN button,
  4. Cover of the battery compartment,
  5. Transmission control light,
  6. Group selector (model dependent),
  7. Programming button/PROG,
  8. Group control lights (model dependent)

General and designated use

It is possible to control all the receivers of the SELVE intronic range and SELVE radio-controlled motors via the SELVE radio transmitters. They should only be used for this purpose.

Explanation of functions/terms used

Transmission control light (model dependent)
A radio signal is indicated by the transmission control light being lit.
Pressing and holding the buttons on the transmitter for a few seconds will cause the transmission control light to go out briefly after 3, 6 and 9 seconds. If the transmission control light is no longer lit when the button is pressed, the batteries must be changed.
Manual/automatic sliding switch (model dependent)
If the sliding switch is set to ‘MANUAL’, only manual travel commands are executed by the receiver (e. g.: UP, STOP, DOWN by pressing the relevant buttons).
If the sliding switch is set to ‘AUTO’, automatic and manual travel commands are executed by the receiver. Group selector (model dependent)
The group selector may be used to select up to 5 channels. Operation of the central command is indicated by all five LEDs lighting up.
INTERMEDIATE POSITION
The intermediate position is a position of the roller shutter/venetian blind between the upper and lower end limits that can be freely selected. This position can be reached from the upper position after programming.

Set intermediate position

SELVE i-R Send 1 Radio Hand Transmitter - Set intermediate
position

Travel to intermediate position

SELVE i-R Send 1 Radio Hand Transmitter - Set intermediate position
1.3

VENTILATION/TILT
The ventilation/tilt position is a position of the roller shutter/ venetian blind between the upper and lower end limits that can be freely selected. Using this function, you can raise the shutter from the lower end limit until the ventilation slits are open. The slats of the venetian blind will be turned.
Set ventilation/tilt

Travel to ventilation/tilt

SELVE i-R Send 1 Radio Hand Transmitter - Set intermediate position
3

Transmitter programming procedure

The operating instructions provided with receivers and other transmitters must be complied with at all times. Please refer to the operating instructions of the receiver or the radio-controlled drive when programming the first transmitter.
Programming further transmitters/channels
Press the PROG button of a programmed transmitter/channel for 3 seconds (wait for confirmation travel from the drive). The receiver is now in programme mode for 1 minute. Briefly press (1 sec.) the PROG button of the new transmitter/channel. The new transmitter/channel has now been programmed. programmed transmitter/channel
new transmitter/channel

SELVE i-R Send 1 Radio Hand Transmitter - Set intermediate position
4

Deprogramming transmitters/channels
Press the PROG button of a programmed transmitter/channel for 3 seconds (wait for confirmation travel from the drive). The receiver is now in programme mode for 1 minute. Briefly press (1 sec.) the PROG button of the transmitter/channel you wish to deprogram. The transmitter/channel has now been deprogrammed.

SELVE i-R Send 1 Radio Hand Transmitter - Set intermediate position
5

Safety instructions

Warning!

  • Use in dry rooms only.
  • Keep persons away from the systems operating range.
  • Keep children away from controls.
  • Always observe country-specific regulations.
  • Dispose of used batteries properly.
  • If the system is controlled by one or more devices, the system operating range must be visible during operation. ning!

Note radio system:

  • Ensure that the controls are not installed and operated in the vicinity of metal surfaces or magnetic fields. Metal surfaces or panes of glass with a metallisation within the transmission path can reduce the range considerably.

  • Before installing in the position required, check that the transmitter and receiver are functioning properly.

  • Please note that radio sets cannot be operated in areas with increased risk of interference (e. g. hospitals, airports).

  • The remote control is only permitted for equipment and systems with which a malfunction in the hand-held transmitter or receiver does not present a risk to persons,
    animals or objects, or this risk is covered by other safety devices.

  • The operator does not enjoy any protection from disturbances by other remote signalling equipment and terminal equipment (for example, also by radio sets operated  n the same frequency range in accordance with regulations).

SELVE i-R Send 1 Radio Hand Transmitter - Set intermediate position
7

Explanation of displays and buttons
1UPbutton, 2 STOP button, 3 DOWN button, 4 Manual/automatic sliding switch, 5 Transmission control light, 6 Programming button/PROG (Remove the wall mount)

SELVE i-R Send 1 Radio Hand Transmitter - Set intermediate position
9

Installing the wall mount
Fix the mount to the wall with the two screws provided.

SELVE i-R Send 1 Radio Hand Transmitter - Set intermediate position
8

i-R Wall Send/i-R Wall Send Basic
Fix the mount to the wall with the two screws provided.

SELVE i-R Send 1 Radio Hand Transmitter - Set intermediate position
10

Changing the battery

  1. Open the battery compartment door.
  2. Take out the batteries.
  3. Insert the new batteries (LR 03; AAA) in the correct position.

Changing the battery

  1. Disconnect the operating device.
  2. Remove the battery.
  3. Insert the new battery properly (CR 2032).

SELVE GmbH & Co. KG
Werdohler Landstraße 286
D-58513 Lüdenscheid
Tel.: +49 2351 925-0
Fax: +49 2351 925-111
Internet: www.selve.de
E-Mail: info@selve.de

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals