SELVE 298751 i-R Marki WS Radio Awning Control Instruction Manual

SELVE 298751 i-R Marki WS Radio Awning Control Instruction Manual

Safety instructions

Warning!

• Risk of injury through an electric shock.
• Terminal connections to a 230 V network must be made by an authorised electrician.
• Disconnect all connecting cables throughout the system before carry ing out installation or maintenance.
• Ensure that the device cannot be accidentally switched on.
• The provisions of the local public utilities and stipulations for wet and damp rooms in accordance with VDE 100 must be observed when the system is connected.
• A potential-free control output is not suitable for safety extra low voltage.
• For use with unmodified original SELVE parts only.
• Keep persons away from the systems operating range.
• An automatically controlled roller shutter or sun protection system can move unexpectedly. Therefore, never place objects in the travel range.
• Keep children away from controls.
• Always observe country-specific regulations.
• If the system is controlled by one or more devices, the system operating range must be visible during operation.
• Please observe the instructions for the roller shutter, sun protection system, motor and control.
• Always adhere to relevant building regulations.
• Automatic and manual movement when frozen (e.g. frozen wind wheel) and during storms can seriously damage the system.
• The receivers (e.g. radio control) no longer function correctly after a power failure. In this case, an extended sun protection system cannot be retracted, e.g., during a storm.
• Never use the control unit if the system or control unit are damaged.
• Always retract the sun protection if a storm is imminent.

Explanation of displays and buttons

Setting the sun and wind threshold values

The values can be set with the i-R Marki Send WS and the i-R Marki Send Plus.
Please refer to these operating instructions for the setting.

Rain sensor (only i-R Marki WSRF)

The awning automatically retracts when it starts to rain. Automatic extension is pre vented.

Transmission control light

A radio signal is indicated by the transmission control light being lit.

Change-over switch awning/Venetian blind (only i-R Marki WS/WSRF/Transmit WS)

The control output of the sensor can be set to awning mode (bottom)/Venetian blind mode (top) via coding switch 1.

Change-over switch drive control device/group control device
(only i-R Marki WS/ WSRF)

The control output of the sensor can be set to drive control device (bottom)/group control device (top) via coding switch 2.

UP-/STOP-/DOWN button

Use these buttons to operate the system from the sensor (e.g. testing of the transmission path).

Programming button

Use this button to program the sensor into the receiver. Additional sensors can be programmed for the i-R Marki WS/WSRF.

General/Designated use

General
The i-R Marki WS/WSRF/Solar WS/Transmit WS controls the sun protection system based on solar intensity and wind speed. These values can be set via the i-R Marki Send WS and i-R Marki Send Plus. The i-R Marki WSRF also controls the sun protection system based on rain/snow and frost. The i-R Marki WS/WSRF has an additional control output for connecting a motor.

Designated use
The i-R Marki WS/WSRF/Solar WS/Transmit WS may only be used for controlling sun protection and venetian blinds systems

• The i-R Marki Solar is unsuitable for controlling blinds that are also used for privacy during the hours of darkness, since correct functioning of the i R Marki Solar cannot be guaranteed at night. Automatic retraction occurs if the power supply is in sufficient.
• Please note that radio sets cannot be operated in areas with increased risk of interference (e. g. hospitals, airports).
• The remote control is only permitted for equipment and systems with which a malfunction in the hand-held transmitter or receiver does not present a risk to persons, animals or objects, or this risk is covered by other safety devices.
• The operator does not enjoy any protection from disturbances by other remote signalling equipment and terminal equipment (for example, also by radio sets operated in the same frequency range in accordance with regulations).
• Only connect the radio receiver to devices and systems approved by the manufacturer.

Installation/Connection

Note:
Ensure that the controls are not installed and operated in the vicinity of metal surfaces or magnetic fields. Metal surfaces or panes of glass with a metallisation within the transmission path can reduce the range considerably.

Radio sets transmitting at the same frequency could interfere with reception.

It should be noted that the range of the radio signal is restricted by legislation and constructional measures.

Installation
Choose a place where the sun intensity and wind speed parameters can be easily measured and, where applicable, objects such as trees and roofs do not affect the light intensity and wind measurements. The sensor can be used for numerous installation situations due to the adjustable wall mount.

Fix the mount to the wall with the two screws provided.

Installation positions

Connection (only i-R Marki WS/WSRF/Transmit WS)

Safety instructions

Warning

• Risk of injury through an electric shock.
• Terminal connections must be carried out by an authorised electrician.
• Disconnect all connecting cables throughout the system before carrying out installation or maintenance.
• Ensure that the device cannot be accidentally switched on.
• A potential-free control output is not suitable for safety extra low voltage (only i-R Marki WS/WSRF).

i-R Marki WS/WSRF

1. Loosen the wall mount.

2. Connect the power line and the motor to the i-R Marki WS/WSRF as follows:
   

3. Place the sensor on the wall mount and fix it using the provided screw.

i-R Marki Transmit WS

1. Loosen the wall mount.

2. Connect the power line and the motor to the i-R Marki Transmit WS as follows:
   

3. Place the sensor on the wall mount and fix it using the provided screw.

Functions of the i-R Marki Solar WS/Transmit WS

Functions of the i-R Marki WS/WSRF

Explanation of functions/terms used

Wind protection function

Retracts and blocks extension of the awning if the wind threshold value is ex ceeded (preset delay: 15 min.).

Sun protection function

Extends the awning if the sun threshold value is exceeded (preset delay: 5 min.).
Retracts the awning if the sun threshold value is not achieved (preset delay: 15 min.).

Rain protection function (only i-R Marki WSRF)

Retracts the awning and prevents automatic extension.

Frost protection function (only i-R Marki WSRF)

Prevents extension of the awning at temperatures below +4 °C.

Twilight function

Retracts the awning during twilight hours (mornings and evenings).

TEST MODE

It is possible to test the sensor in this mode. In the TEST MODE the times of the sun protection and wind protection functions are reduced from minutes to seconds. A possible wind alarm is reset.

Data transfer

The sensor transfers the current wind and sun values to the receiver via radio signals at approx. one minute intervals.

Awning indicates:

Wind alarm ➞ Manual extension is stopped after 2 sec. and the awning re tracts.
Sensor loss ➞ Manual extension is stopped after 4 sec. and the awning retracts.

Transmitter programming procedure

Transmitter programming procedure

Sensor as transmitter

Programming the sensor
Press the PROG button on the receiver or a programmed transmitter for 3 seconds (wait for confirmation: brief upwards and downwards movement of the motor). The receiver remains in programming mode for 1 minute. Briefly press (1 sec.) the PROG button of the sensor. The sensor has now been programmed.

Deprogramming the sensor
Press the PROG button on the receiver or a programmed transmitter for 3 seconds (wait for confirmation: brief upwards and downwards movement of the motor). The receiver remains in programming mode for 1 minute. Briefly press (1 sec.) the PROG button of the sensor. The sensor has now been deprogrammed.

Sensor as receiver (only i-R Marki WS/WSRF)

Programming a transmitter (only i-R Marki WS/WSRF)
Press the PROG button on the sensor for 3 seconds (wait for confirmation: brief upwards and downwards movement of the motor). The receiver remains in programming mode for 1 minute. Briefly press (1 sec.) the PROG button of the transmitter which is to be programmed. The transmitter has now been programmed.

Deprogramming a transmitter (only i-R Marki WS/WSRF)
Press the PROG button on the sensor for 3 seconds (wait for confirmation: brief upwards and downwards movement of the motor). The receiver remains in programming mode for 1 minute. Briefly press (1 sec.) the PROG button of the transmitter which is to be deprogrammed. The transmitter has now been deprogrammed.

Functions in reprogramming mode
(only i-R Marki WS/WSRF, only for qualified personnel)
In order to carry out the following settings, the receiver has to be put into reprogramming mode by disconnecting it from the mains supply.

Note:

• A transmitter has to be correctly programmed before it can be put into reprogramming mode.
• The receiver remains in service mode for 4 minutes.
• Only the put the receiver which is to be set into reprogramming mode.
• In order to take a receiver out of reprogramming mode (e. g. 3 re ceivers at one fuse), the motor has to be actuated.

The receiver confirms the service mode by a brief up and down moving of the motor.

Reprogramming if a transmitter is faulty or lost
Only use if a programmed transmitter is no longer available (faulty or lost). In order to program a new transmitter, the receiver has to be put into reprogramming mode by disconnecting it from the mains supply. Subsequently press the PROG button of the new transmitter for 3 sec.. All the old transmitters have been deprogrammed.

Reset the receiver to the factory setting
(only i-R Marki WS/WSRF, only for qualified personnel)
The factory setting means that no transmitter has been programmed and no intermediate positions have been set. In order to reset to receiver to the factory setting, the receiver has to be put into reprogramming mode by disconnecting it from the mains supply. Subsequently press the PROG button of the sensor for 9 sec..

Technical data

Maintenance
Clean the device with a damp cloth only. Do not use a cleansing agent since this could damage the plastic.

Technical data
Nominal voltage: 230–240 V AC/50–60 Hz (only i-R Marki WS/WSRF/Transmit WS)
Switched current: 5 A/250 V AC for cos φ = 1 (only i-R Marki WS/WSRF)
System of protection: IP 33
Permissible
ambient temperature: -20 to +55 °C
Radio frequency: 868,3 MHz

The maximum radio range is up to 25 m indoors and up to 350 m in the open.
Subject to technical modifications.

General conformity declaration
The company SELVE GmbH & CO. KG, hereby declares that the i-R Marki WS/WSRF/ Solar WS/Transmit WS is in conformity with the basic requirements and other relevant provisions of the Directive 1999/5/EC. The declaration of conformity can be seen at
www.selve.de.

Troubleshooting

Carry out the following tests if a fault arises:

Test ist o.k.
Motor does not function| Program the sensor into the receiver
Reduce the distance to the receiver
Check connection
Actuate the motor via the travel button of the awning hand-held receiver| Motor functions| Test ist o.k.
Motor does not function| Program the sensor into the receiver
Reduce the distance to the receiver
Problem| Cause| Solution
---|---|---
Awning does not extend when the sun is shining| Sun threshold value set too high| Lower the sun threshold value
System in manual mode| Set sliding switch MAN/AUTO to AUTO
Sensor positioned in the shade| Change the position of the sensor
The system is in wind alarm| Wait until the wind abates
Have the wind threshold value reset by a specialist
Awning remains extended even if there is no sunshine| Awning was extended manually| Toggle the sliding switch MAN/AUTO once and then set it to AUTO
Sun threshold value set too low| Set the sun threshold value higher
Awning retracts if there is a slight breeze| Wind threshold value set too low| Have the wind threshold value reset by a specialist
Awning does not retract if there is strong wind| Sensor is positioned in the lee| Change the position of the sensor
Wind value is set too high| Have the wind threshold value reset by a specialist

References

• Ihr Partner für alles rund um Rollladen & Sonnenschutz | SELVE

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>