ika JZY Series Gas Hob User Manual

June 3, 2024
IKA

JZY Series Gas Hob

Foreword & Contents
Foreword
“Beautiful life starts from your kitchen”. Thanks for purchasing Ika kitchen appliances. Ika kitchen appliances undertake the social mission to provide beautiful kitchen lives for mankind, and Ika is committed to becoming the best kitchen life solution supplier in the world. We adhere to the purpose of quality first and customer foremost. If you have any comments and suggestions, please don’t hesitate to contact us, and we will provide perfect services according to your needs. Warning: Before installing and using, please read this Manual carefully, and get familiar with the safety precautions in order to use it properly. Note: The appearance and structure of our products are subject to change without prior notice.
Contents
Foreword Product Diagrams Specifications and Parameters Safety Instructions Installation Method Method of use Operation instruction for gas detector Cleaning & Maintenance Troubleshooting Statement of Environmental Impact Packing List Warranty Information

Product Diagrams

Pot rack Inner burner cap Outer burner cap Gas plate
Panel
Pot rack location
Knob
Door Laedfjtuostuintegr pwlainted Door Laedfjut sintinnegr pwlainted
Gas inlet

Ignition pin (white) Burner Thermocouple (yellow)
Right inner wind DRoigohrt aodujtuesrtiwngindplate Door adjusting plate Battery compartment (uaspinpgliebsattotepryr)oducts

Door Laedfjtuostuintegr pwlainted Door Laedfjut sintGinneagrspwilnainlteedt

RDiogohrt aindnjuesrtwinigndplate RDiogohrt aodujtuesrtiwnigndplate
(uBaspainpttgleierbysacttotoempryrp)oadrutmctesnt

Gas detector (aepqpuliiepspetod pwroithdugcatss

(Aapdpalpietesrtiontperrofadcuects

using

mains

supply)

detector)

Note: Above figures are structure diagrams of the product. The figures are used to identify parts location. Please refer to the product for the actual appearance.

A(adpappliteesr tinoteprrfoadcuects using mains supply)

Specifications and Parameters

Model

JZY series

Gas category

LPG 20Y

Rated gas pressure

Rated heat load

See nameplate on the cooktop

Power supply

1# or 5# dry cells or 200V mains supply

Weight

See details on the packing case

Dimension

See details on the packing case

Note: Refer to the mark on the nameplate of the cooktop for the rated gas pressure.

Safety Instructions

Caution

Low pressure regulator Medium/high pressure regulator

Be sure to use appropriate pressure regulator. The cooktop is a low pressure gas appliance. Only household pressure regulators in compliance with national standards can be used. Do not use medium pressure or high pressure regulators, or else it may cause hazards. Do not place any inflammable or explosive materials (gasoline, alcohol, fireworks, and high-pressure spraying can) near the cooktop, or else it may cause fire or explosion. Do not put any acidic or alkaline materials on the cooktop in order to avoid corrosion. Do not put any knife, fork, spoon or other metal objects on the cooktop to avoid burn due to heating. If unattended, do not let children use or approach the heating cooktop. Do not impact the panel with heavy object.

Caution

While using the cooktop, do not go out or sleep. Turn off the switch knob and the master gas valve after using. Before sleeping or going out, check if the switch is turned off again. While using the cooktop or the flame is just turned off, do not touch the burner cap, pot rack or panel with hands in order to avoid burn. The cooktop can be used for cooking and boiling water. Do not use it to dry towels or clothes in order to avoid accidents. While using the cooktop, be sure to maintain appropriate ventilation to avoid health hazard caused by carbon monoxide produced by the cooktop in the closed kitchen.

Air circulation

Strong wind

Do not use the cooktop in the places blown by strong wind directly. The flameout protection device of the cooktop can only prevent gas leakage caused by wind blowing or soup spill. Please use the cooktop properly to avoid leakage due to other reasons.

Stop using the Gas Hob immediately, turn off the master valve, open the door and window for ventilation, and contact local After-sales Service Center or gas company to check the reason and eliminate the problem. Before the gas leakage is eliminated, do not ignite or turn on electrical equipment, do not handle the power plug, and do not use mobile phone on site, or else open flame or electric spark will ignite the gas and cause fire or explosion.

P

q

q

r

q

q

s

s

s

t

P

P

q

q

P

s

q

t

s

q

Check if the used gas category and rated gas pressure comply with the mark on the nameplate, and do not use if not. Refer to the structure diagrams and check if the parts of the cooktop are complete and intact.

Pressing direction

Picture of cooktop foot

Status before installation Cooktop foot installation diagram

If the embedded cooktop is used as a desktop cooktop, as shown in the picture, align the clips of the cooktop feet to the mounting holes in the four corners in the bottom of the cooktop, and push to clamp on the bottom shell. After installation, pull the cooktop feet to check if the installation is secure.

Installing battery or adapter

The battery compartment is in the bottom of the cooktop. Please insert the battery according to the polarity indicated on the battery compartment.

Battery compartment (applies to products using battery)

The adapter is in the bottom of the cooktop. Please

insert the adapter into the adapter interface of the

Adapter interface

cooktop, and then plug the adapter into the power (applies to products

outlet.

using mains supply) Adapter (applies to

For products that use dual power supply: If the mains power supply isn’t connected and only

products using mains supply)

battery is used, the cooktop can be ignited, but the gas detector, electronic timing and

luminous knob are unavailable. If the mains power supply is connected but battery isn’t used,

all functions of the cooktop work normally. If the mains power supply is connected and battery

is used, all functions of the cooktop work normally.

Requirements on installation position

(Unit: cm)
Vent
Installing the cooktop

Tprhoepceor ovketnotpilasthioonu.ldIf bLeNGinsctyallilneddeirnispluasceeds,wthiteh dbshiesotgaurnledcaebteefrrortehmtaantihn1ee0dc0oacobmkot.voAepttalheneadscttoh1oe0k0tcoycplmi.nIdsf eperaxschheaouusltd hinosotadlliastiionnstraellqeudi,reremtaeinntsthoef sthpeaceexhaacucsotrdhionogdt.oTthhee dsinhistoetaurfnledcreebnefcronemobtetshtmweaecleloenorkwtthooapknao1np5decnmthineignbtooarcdtkheewr btaoallcaokvrowidall eoxpheanuinsgt htooothde. Tsuhreroduisntdainncgewfraollms othreobcjoeocktstosphould be not smaller than 15cm. If the cooktop is installed in the cupboard, the cthuaptbcooanrndedcototor sthheouclodohkatovpe boontetoomr saenvdetrhael vteontatsl akseureeffaipcsiaehinrotcuoilrdxcyubgleaetnnioosntusipnmptlahylelwecrhutehpnabnotha1er0dc0,oceomnks2tou,prienisorder to wduoerktiongim, epnrospuerer itnhsattaallastmioanlloarmpooournst eoaf lginagsolefathkeed gacuaccpsibdinoelaenrttdsc.oaTrnothbaeevoceiovdoarkcotudoaeptn,etpdslenoaarstiuenrsainellscyttasalnledmntaeevtraionligdmtehseh on the vents.

(Unit: cm)

Take out the cutout template from the packing case, dinrsiltlrhuoclteiosnisnothf ethceocoukttooupt atecmcoprldaitnegatnodthreequired shfiitozsreitz,hoaennttdaabltlyhleeun(natpsilustthhteohwebonctotinoomkthtoeopffitighnuetrheceo, Aomk,otBoupnatnpindagnRehloalree ltehnegsthp,ewciifdicthvaalnudesfilfloeltloswizethoef mthaerkcuotfotuhtetecmutpoluatte; template)

Connecting gas pipe

‘HGLFDWHG

PVC pipe

&UDFN DJLQJ

*DVLQOHWRIWKHFRRNWRS &ODPSWKHKRRS

Connecting with rubber pipe:
6HOHFWGHGLFDWHGUXEEHUSLSHRIPPLQQHU GLDPHWHURURWKHUFXVWRPVSHFLILFDWLRQ DFFRUGLQJWRWKHJDVLQOHWVSHFLILFDWLRQRIWKH FRRNWRS7KHUHFRPPHQGHGOHQJWKLV aFP’RQRWXVHUXEEHUSLSHVWKDWKDYH GHIHFWVRUDJHG
&RQQHFWRQHHQGRIWKHUXEEHUSLSHWRWKHJDV LQOHWRIWKHFRRNWRSWRWKHUHGOLQHFODPSWKH FRQQHFWLRQZLWKDKRRSWRSUHYHQWOHDNDJHDQG FRQQHFWWKHRWKHUHQGWRWKHPDVWHUYDOYHRIJDV VXSSO
‘RQRWSXWWKHUXEEHUSLSHRQWKHFRRNWRSDQG DYRLGFRPSUHVVLRQDQGEHQGLQJRIWKHSLSH

5HGOLQH

*DVSLSH

Hoop

Connecting with metal hose:
&RQQHFWWKHODUJHUQXWMRLQWRIWKHPHWDOKRVHWR WKHJDVLQOHWRIWKHFRRNWRSDQGWLJKWHQLQ SODFH&RQQHFWWKHVPDOOHUQXWMRLQWWRWKH PDVWHUYDOYHRIWKHJDVVXSSODQGDOVRWLJKWHQ LQSODFH

*DVLQOHWRI WKHFRRNWRS /DUJHQXWMRLQW
6HDOLQJULQJ
6PDOOQXWMRLQW 6HDOLQJULQJ

Note:
7KHQXWMRLQWVRQERWKHQGVRIWKHPHWDOKRVH PXVWKDYHVHDOLQJUXEEHUULQJVEHIRUHLQVWDOOLQJ DQGXVLQJ

0HWDOKRVH
0DVWHUYDOYHRI WKHJDVVXSSO

Check if the installed gas connector leaks:
$SSOVRDSZDWHURQFRQQHFWLRQVRIWKHJDV SLSHDQGRSHQWKHPDVWHUYDOYHLIDLUEXEEOHV DUHSURGXFHGWKHSLSHOHDNVSOHDVHFORVHWKH PDVWHUYDOYHWLJKWHQWKHFODPSWKHJDVSLSHRU WKHQXWMRLQWDSSURSULDWHODQGWUDJDLQXQWLO WKHUHLVQROHDNDJH&KHFNWKHFRQQHFWLRQV UHJXODUOLQODWHUXVH

Installing gas plate and burner cap

Thermocouple positioning post Thermocouple positioning post Thermocouple

Align the thermocouple positioning post and ignition

pin positioning post on the gas plate to the

Ignition pin thermocouple and ignition pin respectively and install

positioning on the burner, and then put the outer burner cap and

post inner burner cap on the gas plate in sequence. If the

burner cap has positioning pin, put the pin in the

positioning slot in the gas plate.

Ignition pin positioning

Positioning pin

Inner positioning hole Positioning pin Outer positioning hole

post

Ignition pin

Installing pot rack

Positioning slot (bottom)

Put the pot rack in appropriate position on the cooktop panel. If the pot rack has positioning slot

Put in alignment in the bottom, align it to the clamp position on the

Clamp position panel, and ensure that the pot rack is flat and

stable

Long side direction

Short side direction Short side direction

Clamp the heat shields on the pot rack according to the long side direction and short side direction shown in the figure.
Long side direction

Method of use

Ignition operation
1. Turn all knobs to ” ” position, and open the master valve of the gas supply.
2. Press the knob, turn left counterclockwise to the high heat position ” “, and the flame is ignited automatically when the ignition pin clicks.
Note:
a. If the cooktop you purchased isn’t instant start series, please press the knob for 3-5 seconds when the flame is ignited (flameout protection system of the cooktop needs preheating for 3-5 seconds).

b. If the cooktop you purchased is instant start series, release your hand when the flame is ignited.
Tips: If the cooktop is used for the first time or hasn’t been used for a long time, it is normal if it is difficult to ignite because the gas pipe has air residue. Please try several times to discharge the air until the flame is ignited normally. Do not remove the gas pipe to discharge the air.
Adjusting fire power
Rotate the knob slowly as shown in the figure below to get desired fire power.

OFF

MAX.

MIN.

OFF

Medium

Strong

Medium

Soft

Low

Remark: Please refer to the cooktop to check if it is general adjustment or accurate adjustment.

Adjusting ventilation door
The adjusting plate of ventilation door is in the bottom of the cooktop, and is used to adjust the flame burning. Under normal conditions, the ventilation door of the cooktop has been adjusted properly, and the burning flame is light blue, clear and stable.

Position of adjusting plate of ventilation door

Normal blue flame

Adjusting method of ventilation door:

Hold the handle of the adjusting plate of the ventilation door, lift about

1mm and then turn left or right. When the handle is turned to the left,

the air inlet of the ventilation door is narrowed and the intake air

quantity is reduced. When the handle is turned to the right, the air

inlet of the ventilation door is expanded and the intake air quantity is

increased.

Air inlet

Handle of the Put the adjusting plate adjusting plate in different notches to adjust the flame burning

The air inlet of the The air inlet of the

ventilation door is the ventilation door is

largest and the intake the smallest and the

air quantity is the intake air quantity

maximum

is the minimum

If the flame is abnormal, please adjust according to the table below:

Abnormal flame

Vadejnutsiltaintigonmdeothoor d

Fholalemoerbtrheearkesisawbiagynforoisme wthheefnire the flame extinguishes. Flame retracts into the burner, nbourfnlaemr ceaopr, faunzdzyacflcaommepoannitehdeby

Nvdeeancrrtrioelawatsiotehnethdaeoiorinrintaalenktdeoafitrhe quantity

whirr

Flame is yellow

Evexnptailnadtiotnhedoaoirrinalnedt of the iqnucarenatistye the intake air

Hood-cooktop linkage
If you have purchased hood-cooktop linkage product of our company (model with L suffix), please set in the following method: (the specific operation depends on the hood model; please refer to the hood manual) 1. Code matching for first use (1) Connect the power supply of the hood, install the battery or connect the power supply for the cooktop. (2) Press and hold the CLOCK button of the hood for three seconds, the CLOCK LED of the hood flashes and enters code matching waiting state. Press and hold the cooktop knob for three seconds and release, and the cooktop will transmit code automatically and match with the hood. When the CLOCK LED of the hood stops flashing, the buzzer beeps long and the icon on the display is lit, indicating that the code is matched successfully and the linkage function starts (whether the cooktop is connected to the gas supply doesn’t affect the code matching) Note: If the electronic control board of the hood or cooktop has been repaired or replaced, please re- match the code in the same method.

2. Control function under linkage state (1) When any burner of the cooktop is ignited, the hood enters
running state automatically in three seconds and adjusts the level according to the fire power automatically. (2) When both burners are turned off, the hood enters slow speed delay state, and turns off in three seconds.
Operation instruction for mechanical timer

1. In initial state, adjust the knob to ” “, the right burner doesn’t have timer function, the timing function is disabled, and the right burner is in normal operation;
2. Adjust the knob to a scale between 1 and 120, the right burner is in timer state, and the timer time is the scale value (unit: min);
3. At the timer time, the timer knob points ” “, tinkles once and the right burner turns off; the timer function of the right burner is disabled and the right burner resumes normal operation.
Remark: The mechanical timer has error. If you need accurate cooking operation, the timer time is only for reference.

Operation instruction for electronic timer

Hour digit

Minute digit

Minute digit

Left burner timer mark

Right burner timer mark

Timer time adjustment

Timer button

Timer time adjustment

1. Standby state: When the power is connected for the first time or reconnected after power failure, the buzzer beeps once, the illuminated pushbutton and display turn off after two seconds, and the timer function enters standby state. The system is in non-timer state by default, and the digital display area is hidden in this state;

2. The ignition operation of cooktops with timer operation is same as conventional cooktops; When the timer counts down to “0:00”, the buzzer beeps once and turns off the burner; The buzzer beeps once when the button is pressed down.

3. Timer setting:

  1. Turning on the timer:

When the burner is burning, tap the timer button to turn on the timer,

and the system enters left burner timer setting by default, and the left

burner timer mark and digital display area

flash at the same

time, indicating that the left burner is in timer setting state. To set the timer

function of the right burner, tap the timer button again, and the right

burner timer mark and digital display area

flash at the same time;

tap the timer button to switch the timer function between left burner

and right burner; when the timer function is turned on, the digital display

area shows the timer time set in previous time by default.

  1. Turning off the timer: If the timer time is set to “0:00” and there is no operation in 5 seconds, it will exit the timer function; When the timer function is turned on, the set time ends; exit timer function and turn off the burner; When the timer function is turned on, press the pushbutton again to ignite and exit the timer function; Exit timer function if the burner is turned off.

  2. Timer time setting: When the timer function of the burner is turned on, that is, the burner timer mark and digital display area flash at the same time, and enter the timer setting state of respective burner; Press the + or – button to increase or decrease the time by 1 minute; press and hold the + or – button to increase or decrease the time by 10 minutes; the range of timer time: 0:01-9:59;

If there is no operation in 5 seconds after setting the time, it will enter the timer state, the digital display area shows the set time, and the timer mark or of respective burner turns on, indicating that the burner is in timer state. 4) Editing timer time: In timer state, tap the timer button to enter timer time setting state of the left burner, and the digital display area shows the previously set timer time; the setting and operation of timer time are same as the description in 3). 5) The left and the right burner can use the timer function at the same time as described in steps 1) ~ 4). After confirming and entering countdown, the countdown time switches between the left and the right burner; when is on, it shows the timer time of the left burner; when is on, it shows the timer time of the right burner.
Operation instruction for gas detector

  1. When external power is connected, the product enters preheating mode (2~4min), the green LED flashes, and the gas detector doesn’t detect gas leakage at this time. 2) After preheating, the product enters detection mode, the green LED turns on, and it will send sound alarm if the detected gas exceeds set threshold (10%~20%LEL). It also controls the pulse igniter to disable ignition. 3) If there is sound alarm, please close the master valve of the gas supply immediately, open the window for ventilation, and contact local After-sales Service Center or gas company to check the reason and eliminate the problem. Before the gas leakage is eliminated, do not ignite or turn on electrical equipment, do not handle the power plug, and do not use mobile phone on site, or else open flame or electric spark will ignite the gas and cause fire or explosion. 4) When the gas leakage is eliminated, connect the power and wait for 2~4 minutes; if the gas detector doesn’t alarm, the cooktop can be used normally.

Note
The gas detector alarms only when the gas leakage reaches set threshold. Therefore, if the cooktop is in the environment with good ventilation or big air flow and the gas leakage can’t reach the set threshold, it won’t alarm. Do not cover the gas detector with any object. When the power is just connected and the green LED flashes, the gas detector is in preheating mode and can’t detect normally. Since the product is installed in closed cupboard, it also may alarm due to gas accumulation after long time use; in this case, open the window for ventilation, open the cupboard for several minutes to discharge the gas until there is no alarm. Drill vents in the cupboard as required by this Manual. The damages and losses caused by incompliance with the installation methods and usage methods specified in this Manual are not covered by the free warranty of the manufacturer. The manufacturer also doesn’t assume any related responsibilities. Please keep all documents properly.
Cleaning & Maintenance
Regularly check if the rubber pipes are intact and if there is any aging or crack; replace the pipes regularly (once a year recommended). Before cleaning the cooktop, turn off the master valve of the gas supply and wait for the cooktop to cool down. Clean the counter and surrounding of the cooktop regularly (once a day recommended). Clean the cooktop surface with soft cloth and neutral (or dedicated) detergent; do not use steel ball or other hard objects. Clear the dirt on the burner surface, ignition pin and thermocouple surface with soft brush and neutral (or dedicated) detergent; do not use steel ball or other hard objects. Clear the carbon deposits in the inner and outer burner cap with thin sheet iron or steel needle to avoid blocking the fire hole and affecting normal use. After cleaning, install the gas plate, burner cap and pot rack in place (refer to the installation method).

Troubleshooting

Failure
Can’t ignite

Cause
Touhte master valve is closed or gas is run Binastuteffricyieisnnt’t installed, reverse or power Gas pipeline is mixed with air
Rubber hose is bent or squashed

Solution
Ogapsen the master valve or replace the Install the battery properly or replace the battery Ignite repeatedly to discharge the air
Straighten or replace the hose

Safety system isn’t preheated sufficiently Ignite and hold the knob for 3~5 seconds

Ignition pin has dirt in the tip

Clean

Ignition pin isn’t in proper position

Apidnjuasntdthbeurdnisetracnacpe tboe3tw~e5emnmthe ignition

Gas leakage (smell gas)

Rubber pipe is aged, cracks or falls off Pipes are not connected properly

Replace or reconnect the rubber pipe Ca”Cnhodenccnkoentchnteienctgitggphartonspepesisrplyeo”f()rtehfeerctoonnections

Flame is red Air humidity is too high, too much fume Normal phenomenon

Flame is yellow

LNG in the cylinder is almost run out Replace the LNG The fire hole of the burner cap is blocked Clear the dirt Tsmhealal ir inlet of the ventilation door is too Aadiodrojiunrs”l)et tth(reefveernttoila”Atiodnjudsotinogr tvoeenxtiplaatniodnthe

Fawlaamyefrbormeatkhse fire hnflaoomlieseeower xthhteiennrgetuhiissehbeigs

Tbihge air inlet of the ventilation door is too

Adjust the ventilation door to narrow the adioroinr”l)et (refer to “Adjusting ventilation

Flame retracts innotofltahmeebourrnfuezr,zy fbalaucmcrnoeemropcnaantphi,eeadnbdy whirr

The burner cap and gas plate are not placed properly The air inlet of the ventilation door is too big

Place the burner cap and gas plate properly; follow the positioning if available Adjust the ventilation door to narrow the adioroinr”l)et (refer to “Adjusting ventilation

Hafoteordigdnoietinsng’t start Tlinhkeahgoeofdundcotieosnn(‘tmhoadveel hwoitohdL-csouofkfitxo)p

(caopopkltioepsstowith hlinokoadg-ceofoukntcotpion of

Loinnkage function of the hood isn’t turned

msuoffdixe)ls with L Tcohoeketolepcitsricoaxlidcioznetdroolrbbouarrndt of the

Ulinskeatgheefhuonoctdiotnhat has hood-cooktop Turn on the hood-cooktop linkage function Ask qualified personnel to replace

If the problem still can’t be eliminated, please ask designated service department to repair.

Statement of Environmental Impact
The company establishes, implements, and maintains environment management system in accordance with national standard. The environmental impacts of the products in use and after service life expires are as follows: The paper boxes and plastic bags can be recycled, but foam can’t be recycled and should be disposed of into dedicated trash can after unpacking. The waste batteries can be recycled and should be disposed of into dedicated trash can, or else it will cause environmental pollution. The product in use will discharge CO, CO2, NOX and other waste gases. Please keep ventilation of the room. Poor ventilation will cause the concentration of CO, CO2, NOX and other waste gases rising significantly, which will harm your health and cause hypoxia poisoning or even death. Every product has its service life. Please scrap it according to national regulations. The scrapped product shall be sent to local collection station.
Packing List

Cooktop 1 set Cutout template 1pcs
Clamp hoop 1pcs Adapter 1pcs

User’s Manual 1pcs
Auxiliary tine pot rack 1pcs Auxiliarpyostmraacllk 1pcs Cooktop feet 4pcs

Note: 1. Clamp hoop isn’t provided for the areas using G1/2 screw. 2. Auxiliary tine pot rack and small pot rack are optional for certain models. 3. Certain models are not recommended for desktop cooktops, and cooktop feet are not provided. 4. Adapter is only equipped for products using mains supply.

Warranty Information
The free warranty doesn’t cover the following cases, but we can provide charged services. The authorized service outlets provide charged services for the following cases: (1) The damage is caused by improper handling, use, maintenance or storage; (2) The damage is caused by installation or maintenance in unauthorized service
outlets (including installation or repair by the user); (3) The user can’t offer valid invoice or proof of purchase, and can’t proof the
warranty period; (4) The invoice doesn’t match the product or is altered; (5) The damage is caused by force majeure; (6) Beyond the warranty period; (7) The damage is caused in the environment (e.g. voltage, humidity, temperature,
ventilation, etc.) incompliance with the Manual.
Note: The product is subject to change without prior notice.

Tips
Before installing the product, drill vents in the cupboard with total area not smaller than 100cm2 according to the “Requirements on installation position” in this Manual. The cooktop is a low pressure gas appliance. Please use appropriate pressure regulator. Do not use medium pressure or high pressure regulators, or else it may cause hazards. To ignite, press the knob to the bottom and rotate left for 90° to the ignition position; after igniting, hold the knob for 3~5 seconds before releasing (because the flameout protection system requires preheating). For first use, please ignite several times to discharge the air from the pipe. If the ignition sound is weak, please replace the battery. It is
roepceormatminegntdimede.to use high capacity alkaline battery to extend the

Ï

Ð

Ñ

Ð

Ò

Ï

Ð

Ó

Ð

Ô

Ï

Ò

Õ

Ï

Ñ

Ð

Ö

×

Ø

Ù

Ú

Û

Ö

×

Ø

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals