KEEM IKA W500 Intelligent Visual WI-FI Industrial Endoscope Instruction Manual

Intelligent Visual
WIFI Industrial Endoscope

Product Description

W200 is a WiFi industrial endoscope camera with an HD camera. The mobile phone connects to the product’s WiFi transmits a signal, and the images are displayed on the APP, must be previously downloaded. This product is equipped with a small-diameter HD camera with auxiliary LED lighting. The camera contains a high-sensitivity chip, which can be used normally even in dark working environments.

Safety and Maintenance Information

• Please remember to turn off the W200 and place it in a dry environment after peruse. You can use a soft cotton cloth with little alcohol to keep the camera lens clear.
• The storage and the working temperature should between 32°F-113°F.
• The unit is not shock-resistant. Please avoid high-impact results from things such as dropping the unit from height. Do not hit the camera violently and do not pull the cable abruptly.
• When used in an environment with sharp bumps, please use it carefully to prevent the waterproof protective layer of the probe from being scratched.
• The lens and the lens cable are water-resistant when the unit is fully assembled, but the WiFi box is not. IP67 waterproof is for the camera probe part only, and the camera part supports underwater inspections within 3.33ft / 30 mins.
• The camera probe is not made of heat-resistant and high-temperature materials. When checking the automobile engine, please ensure that the temperature in the engine drops to the normal temperature.
• When not in use, please ensure that the lens and the main unit are clean and dry, and avoid contact with oil, acid, and other corrosive and dangerous substances, etc. These may increase the risk of electrical shocks and damage to the device.
• This product is not suitable for people with limited physical, sensory, or mental abilities.
• Childs can only operate this device with the guidance of adults, please don’t let them operate the device alone.
• If the equipment is damaged, do not disassemble it by yourself.
• The product is an industrial endoscopy camera and is not intended for medical use or human examination.

Note: Do not immerse the WiFi box in water

Battery instructions

• Please use DC 5V 1A or 5V 2A adapter to charge the device. The product does not support fast charging.
• If the device is not used for a long time, please ensure that it is charged at least once every 3 months to prevent irreparable damage caused by excessive discharge of the battery.

Product Structure

1. Front Camera with LEDs light
2. Side Camera with LED
3. The lens port lock switch
4. WiFi signal Indicator A:
5. The blue LED light keeps blinking: WiFi is not connected
6. The blue LED light stays ON: the WiFi connection successful
7. Power Indicator B:
8. Red LED light keeps blinking: low battery
9. Red LED light stays on: charging status
10. Red LED light off while charging: battery fully charged off
11. Power ON/OFF:
12. Press and hold for 3 seconds to turn ON/OFF
13. Turn on the device, then short press to take photos

Instructions

Left slide lens port lock the button, insert the camera port Press and hold for 3 seconds to turn ON/OFF

Install APP

Method 1: Scan the QR code, choose to download the APP. System support (Android4.4+, i0S9.0+ and above) https://qr19.cn/DiUJqs

Method 2: For iOS users, please search “ANESOK” in the App store, download, and install it. System support (I0S9+and above)
For Android users, please search “ANESOK” in Google Play Store, download and install it. System support (Android4.4+and above) Enter the setting interface, turn on the WLAN switch, link the WiFi hotspot “ANESOK-XXXX”, return to the desktop and open the “ANESOK” App

APP Introduction

FAQ and HELP

1. The APP does not display images

(@ Whether the phone is connected to the WIFI hotspot of the device @ Check if the camera light is on, or because the interface is not in good contact, please re-plug and unplug.

2. Lags happened during the photo outputting of the product

Step 1: Keep the distance between the WiFi Industrial Endoscope and the phone/tablet within 5M Step 2: Please check whether the product is fully charged, restart the device, or reassemble the camera connector.

3. The image screen is not clear

The best imaging focal length of the product is: 2cm-10cm, please calibrate the distance to the object, or clean the front of the camera with a clean alcohol cloth.

4. Product charging

Please use DC 5V=1A or 5V=2A adapter to charge the device. The product does not support fast charging.

5. How to output pictures on the phone

6. The camera is heat

It is normal for the camera to heat up, especially when the camera LED light is on at the highest brightness.But it does not affect normal use or service life.

Charging Guide

1. Connect the device to the Type-C USB adapter for charging. The product does not support fast charging.
2. During the charging process, the red LED indicator will be steady.
3. When the device is fully charged, the red LED indicator will go out is off.

Accessories installation Guide

Accessories: Protective ring1, Magnet 1, Hook*1

Camera Specifications

| Dual lens| Single lens
---|---|---
Camera diameter| 7.9mm| 5.5mm| 7.9mm| 5.5mm
Camera resolutioi| 2K
Viewing angle| 78°| 70°
Focusing range| A Camera| 20-100mm| 20-100mm
B Camera| 20-50mm|

Product Specifications

List: Endoscope, Manual. Magnet. Hook, Protective ring.
Type-C charge cable. Lens cable

Thank you.

Documents / Resources

| KEEM IKA W500 Intelligent Visual WI-FI Industrial Endoscope [pdf] Instruction Manual
W500 Intelligent Visual WI-FI Industrial Endoscope, W500, Intelligent Visual WI-FI Industrial Endoscope, Visual WI-FI Industrial Endoscope, Industrial Endoscope, Endoscope
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>