SKINXTC SculptX Microcurrent Skincare and Beauty Device User Guide

: June 12, 2024
: SKINXTC

Table of Contents

SKINXTC SculptX Microcurrent Skincare and Beauty Device
Product Information
Product Usage Instructions
OVERVIEW
Charging SculptX
SculptX Instructions
SculptX Get Started
SculptX Steps
SculptX Cautions
SculptX Specifications
SculptX Frequency of Use
Contraindications
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SKINXTC SculptX Microcurrent Skincare and Beauty Device

SKINXTC-SculptX-Microcurrent-Skincare-and-Beauty-Device-
PRODUCT

Product Information

The SKIN XTCTM SculptX Microcurrent LiFT Skincare & Beauty Device is a portable device designed to provide microcurrent therapy and red LED light therapy for the face. It features silver contact spheres for effective treatment and 5 level and intensity control lights for customization. The device is charged through a USB charging point and has an on/off power button for easy operation. It comes with a box dimension of L: 14cm x W: 14cm x H: 5cm and weighs 300 grams. The power frequency is 0.3Hz, and the red LED light depth is 650nm. The device comes with a Type C USB cable for charging.

Product Usage Instructions

Wash your face with an oil-free cleanser and pat dry.
Apply a water-based conductive gel or water-based serum to the area of the face you want to treat.
Switch on the SculptX device using the power button and select your desired level of microcurrent intensity indicated by the number of blue lights.
Every 5 seconds, a beep will sound to indicate that you should move to the next pass. It is recommended to do 3 passes to one area.
Use a combination of glide passes with lift and hold techniques.
Spritz water on your face periodically to prevent the skin from drying out and to maintain high conductivity levels of microcurrent energy.
Repeat the above steps on all areas of your face, working from the neck to the forehead.
Clean the SculptX device with a dry micro-fiber cloth after use.

OVERVIEW

SculptX Microcurrent Device $SKINXTC-SculptX-Microcurrent-Skincare-and- Beauty-Device-FIG-1 $1$$

Charging SculptX

Ensure to charge SculptX for an initial full 3 hours, before switching on.
Blue lights will flash when SculptX is charging.
LIFT must be switched off before charging.
Type C USB charge cable is used for SculptX.
Charge your SculptX once each week.
Always switch off SculptX before charging (do not use the device while on charge).
Charging is complete when the blue lights stop flashing, (bar the initial 3-hour charge).

SculptX Instructions

Switch on SculptX with one quick press of the power button.
Change SculptX level intensity from level 1 to 5 by pressing the power button.
A number of blue lights on your SculptX device represent the level selected.
Red LED light therapy is programmed to come into use when you switch on SculptX.
Press the power button for 2 seconds to turn off the red LED light therapy, (repeat to switch it on).
SculptX is programmed to switch off after 5 minutes to prompt you to treat a different section of the face or neck
Press the power button and hold for 3 seconds to switch off SculptX.

SculptX Get Started

$SKINXTC-SculptX-Microcurrent-Skincare-and-Beauty- Device-FIG-1 $2$$

Divide the face into four sections when doing a full face treatment.
Under the eyes marks the vertical halfway point.
Apply adequate water-based gel for conductivity of microcurrent energy.
Spray water to stop the area from drying out and to ensure maximum results are achieved.

SculptX Steps

$SKINXTC-SculptX-Microcurrent-Skincare-and-Beauty-Device- FIG-1 $3$$

Wash face with oil-free cleanser and pat dry
Apply water-based conductive gel or water-based serum to the area of the face for treatment.
Switch on SculptX with the power button and select your level of microcurrent intensity indicated by a number of blue lights.
Every 5 seconds a beep will sound to indicate to move to the next pass. It’s recommended to do 3 passes to one area.
Use a combination of glide passes with lift and hold techniques.
Spritz water on the face to prevent skin from drying out and to maintain high conductivity levels of microcurrent energy.
Repeat to all areas working from the neck to the forehead.
Clean SculptX with a dry microfibre cloth.

SculptX Cautions

$SKINXTC-SculptX-Microcurrent-Skincare-and-Beauty- Device-FIG-1 $4$$

Do not use it on the upper eyelids, eyeballs, around the ears, or over the thyroid area.
Do not treat inner eye orbital bone areas that surround the eye.
Do not use on the mucosa which is a membrane that lines cavities of the body.
Do not submerge under water. The device is not waterproof.