legrand WNRL10 Radiant Single Pole Universal Wall Switch Instruction Manual

legrand WNRL10 Radiant Single Pole Universal Wall

Catalog Number(s)

REGULATORY INFORMATION

FCC NOTICE: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesirable operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 10 mm between the transmitter’s radiating structure(s) and the body of the user or nearby persons.

NOTE: Any changes or modifications to this device that are not expressly approved by the manufacturer will void the warranty and the user’s authority to operate the equipment.

Contains FCC ID: 2AU5D982057
IC NOTICE: This device complies with Industry Canada license-exempt RSS standards. Operation is subject to the following two conditions:

1. This device may not cause interference; and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

RF EXPOSURE STATEMENT: This equipment meets the SAR evaluation limits given in RSS-102 Issue 5 requirements at the minimum separation
distance of 10 mm to the human body. Note: Any changes or modifications to this device that are not expressly approved by the manufacturer, will void the warranty and the user’s authority to operate the equipment.

IC: 25764-982057
HVIN: 982057

BEFORE YOU START

Review this guide in its entirety. Consult an electrician with any questions or if you are unsure of your abilities.
Warning: Incorrect installation could result in death, serious injury, and/or damage to your home or devices.
Caution: To reduce the risk of injury and/or overheating and damage to other equipment:

• For dry, indoor use only.
• Do not use to power medical equipment – not suitable as a disconnecting means.
• Do not use with loads exceeding the device load rating.
• Connect the smart switch to a 120 VAC, 60 Hz power source ONLY.
• Always use copper wire to install the smart switch & follow all applicable local & national electrical codes.

WHAT YOU NEED

Required:

• Phillips-head screwdriver
• Flat blade screwdriver

You May Also Need:

• Voltage tester, pliers, wire cutter, wire stripper, electrical tape, flashlight, wiring leads (included), and wire nuts (included).

INSTALLATION & SETUP

1. Turn off power to device at circuit breaker
   Flip existing light switch multiple times to confirm power is off. NOTE: Ensure power is off to all devices in electrical box.

2. Remove existing device
   Check for the following wires:

   • HOT or LINE: Receives power from the circuit box. Referred to as “hot” for the purpose of this guide. Do not touch or let “hot” wire contact other wires.
   • LOAD: Directs power to your light(s).
   • NEUTRAL: Creates a path to return current to the power source when the device is off. Required for your switch installation.
   • GROUND: Provides a safe path for electricity in the even of a short circuit.

3. Wire Smart Switch
   Use the wire nuts provided to secure the wires together.

   • Connect the WHITE neutral wire on the switch to the neutral wires in the box, using the red wire nut.
   • Connect the LOAD wire on the switch to the load wire(s) in the box.
   • Connect the HOT wire on the switch to the hot wire(s) in the box.
   • Connect the GREEN ground wire on the switch to the ground wire(s) in  the box.

4. Secure Smart Switch

   • Fold the wires into electrical box, taking care not to pinch a wire.
   • Use included screws to secure smart switch to electrical box. Do not fully tighten the screws.

5. Test The Smart Switch
   NOTE: See getting to know your switch section for feature details. Turn the power back on at the circuit breaker, press switch to turn light on/off.
   This device is designed to work with a radiant® Smart Gateway with Netatmo. Follow the instructions from your app to finish setting up your switch. TROUBLESHOOTING TIP: If the device is not powering check wiring to determine if you have reversed the “HOT” and “LOAD” wiring.

6. Attach Wall Plate

   • Use the sub-plate screws (provided) to secure the sub-plate to the smart switch.
   • Tighten device screws to secure smart switch to the electrical box.
   • Angle the UP end of the wall plate over the top edge of the sub-plate. Push the screwless wall plate down and in until it “snaps” into place over the sub-plate.
     NOTE: To remove the wall plate, place the tip of a flat blade screwdriver into the slot under the wall plate and twist gently.

7. Set Up Your System

   • Download and launch the Legrand Home + Control app. The app is available on the App Store or on Google Play.
   • Connect your smart device to your home network by following the step by step instructions in the app.
   • Use the app to control your smart device.

For the most recent instruction sheets or more information on this product, please see this link or scan the QR code: https://www.legrand.us/p/wnrl10wh

GETTING TO KNOW YOUR SWITCH

of paddle to turn light off.
2| LED Loca- tor Light| Indicates the current state of device. Refer to “LED Locator Light Explanations” for detail.
3| EZ Button| Used to enter setup mode.

LED Locator Light Explanations

Reset To Factory Default
Deleting a device from the app will reset it to factory defaults.
To manually reset the device to factory defaults press and hold the EZ button for 10 seconds until you see the LED blink red then release. The LED will change to solid red when the reset is complete.

SPECIFICATIONS

Legrand reserves the right to change specifications without notice.

LIMITED ONE YEAR WARRANTY

Legrand will remedy any defect in workmanship or material in Legrand products which may develop under proper and normal use within ONE year from date of purchase by a consumer:
(1) by repair or replacement, or, at Legrand’s option, (2) by return of an amount equal to consumer’s purchase price. Such remedy is IN LIEU OF ANY AND ALL EXPRESSED OR IMPLIED WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Such remedy by Legrand
does not include or cover cost of labor for removal or reinstallation of the product. ALL OTHER FURTHER ELEMENTS OF DAMAGE (INCIDENTAL OR CONSEQUENTIAL DAMAGES) FOR BREACH OF ANY
AND ALL EXPRESSED OR IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED HEREBY. (Some states do not allow disclaimers or exclusion or limitation of incidental or consequential damages, so the above disclaimer and limitation or exclusion may not apply to you.) ANY IMPLIED WARRANTIES INCLUDING WHERE REQUIRED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED TO THE ONE YEAR PERIOD SET FORTH ABOVE. (Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.)
To ensure safety, all repairs to Legrand products must be made by Legrand, or under its specific direction.
Procedure to obtain performance of any warranty obligation is as follows: (1) Contact Legrand, Syracuse, New York 13221, for instructions concerning return or repair; (2) return the product to Legrand, postage paid, with your name and address and a written description of the installation or use of the Legrand product, and the observed defects or failure to operate, or other claimed basis for dissatisfaction. This warranty gives you
specific legal rights and you may also have other rights which vary from state to state.

For covering patents, see www.legrand.us/patents
No: 341305 2/21
© Copyright 2021 Legrand All Rights Reserved.
© Copyright 2021 Tous droits réservés Legrand.
© Copyright 2021 Legrand Todos los derechos reservados.

Questions? We’re here to help.
Phone: 1-877-833-3303 8:00 a.m. to 8:00 p.m. EST (M-F) Email: smartlighting@legrand.us
Chat: https://www.legrand.us/radiant/smart-lighting.aspx
(Click on the chat icon to open a dialogue box)

800.223.4185 1.877.BY.LEGRAND www.legrand.us www.legrand.ca

References

• Patents | Legrand
• Smart Lighting from the radiant Collection ⎸Legrand

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>