audizio 102.326 Toulon Micro Hi-Fi System Instruction Manual

: June 4, 2024
: audizio

audizio 102.326 Toulon Micro Hi-Fi System

audizio-102-326-Toulon-Micro-Hi-Fi-System-PRODUCT

Congratulations to the purchase of this Audizio product. Please read this manual thoroughly prior to using the unit in order to benefit fully from all features.Read the manual prior to using the unit. Follow the instructions in order not to invalidate the warranty. Take all precautions to avoid fire and/or electrical shock. Repairs must only be carried out by a qualified technician in order to avoid electrical shock. Keep the manual for future reference.

Instruction

Prior to using the unit, please ask advice from a specialist. When the unit is switched on for the first time, some smell may occur. This is normal and will disappear after a while.
The unit contains voltage-carrying parts. Therefore, do NOT open the housing.
Do not place metal objects or pour liquids into the unit This may cause electrical shock and malfunction.
Do not place the unit near heat sources such as radiators, etc. Do not place the unit on a vibrating surface. Do not cover the ventilation holes.
The unit is not suitable for continuous use.
Be careful with the mains lead and do not damage it. A faulty or damaged mains lead can cause electrical shock and malfunction.
When unplugging the unit from a mains outlet, always pull the plug, never the lead.
Do not plug or unplug the unit with wet hands.
If the plug and/or the mains lead are damaged, they need to be replaced by a qualified technician.
If the unit is damaged to such an extent that internal parts are visible, do NOT plug the unit into a mains outlet and DO NOT switch the unit on. Contact your dealer. Do
NOT connect the unit to a rheostat or dimmer.
To avoid fire and shock hazard, do not expose the unit to rain and moisture.
All repairs should be carried out by a qualified technician only.
Connect the unit to an earthed mains outlet (220- 240Vac/50Hz) protected by a 10-16A fuse.
During a thunderstorm or if the unit will not be used for a longer period, unplug it from the mains. The rule is: Unplug it from the mains when not in use.
If the unit has not been used for a longer period, condensation may occur. Let the unit reach room temperature before you switch it on. Never use the unit in humid rooms or outdoors.
To prevent accidents in companies, you must follow the application guidelines and follow instructions.
Do not repeatedly switch the fixture on and off. This shortens the lifetime.
Keep the unit out of the reach of children. Do not leave the unit unattended.
Do not use cleaning sprays to clean switches. The residues of these sprays cause deposits of dust and grease. In case of malfunction, always seek advice from a specialist.
Do not force the controls.
This unit is with a speaker inside which can cause a magnetic field. Keep this unit at least 60cm away from the computer or TV.
If this product has a built-in lead-acid rechargeable battery. Please recharge the battery every 3 months if you are not going to use the product for a long period of time. Otherwise, the battery may be permanently damaged.
If the battery is damaged, please replace it with the battery of the same specifications. And dispose of the damaged battery environment friendly.
If the unit has fallen, always have it checked by a qualified technician before you switch the unit on again.
Do not use chemicals to clean the unit. They damage the varnish. Only clean the unit with a dry cloth.
Keep away from electronic equipment that may cause interference
Only use original spares for repairs, otherwise serious damage and/or dangerous radiation may occur.
Switch the unit off prior to unplugging it from the mains and/or other equipment. Unplug all leads and cables prior to moving the unit.
Make sure that the mains lead cannot be damaged when people walk on it. Check the mains lead before every use for damages and faults!
The mains voltage is 220-240Vac/50Hz. Check if power outlet match. If you travel, make sure that the mains voltage of the country is suitable for this unit.
Keep the original packing material so that you can transport the unit in safe conditions.

This mark attracts the attention of the user to high voltages that are present inside the housing and that are of sufficient magnitude to cause a shock hazard. This mark attracts the attention of the user to important instructions that are contained in the manual and that he should read and adhere to. The unit has been certified CE. It is prohibited to make any changes to the unit. They would invalidate the CE certificate and their guarantee!

NOTE: To make sure that the unit will function normally, it must be used in rooms with a temperature between 5°C/41°F and 35°C/95°F.

Electric products must not be put into household waste. Please bring them to a recycling center. Ask your local authorities or your dealer about the way to proceed. The specifications are typical. The actual values can slightly change from one unit to the other. Specifications can be changed without prior notice.

Do not attempt to make any repairs yourself. This would invalidate your warranty. Do not make any changes to the unit. This would also invalidate your warranty. The warranty is not applicable in case of accidents or damages caused by inappropriate use or disrespect of the warnings contained in this manual. Audizio cannot be held responsible for personal injuries caused by disrespect of the safety recommendations and warnings. This is also applicable to all damages in whatever form.

UNPACKING INSTRUCTION

CAUTION
Immediately upon receiving the product, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear damage from shipping or the package itself shows signs of mishandling. Save the package and all packing materials. In the event that the product must be returned to the factory, it is important that the product be returned in the original factory box and packing. If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your device. Leave the device switched off until it has reached room temperature.

PRODUCT OVERVIEW

Open/Close CD compartment
Volume control
Lcd display
IR remote control receiver
Power ON/Standby
Source Button
Clock set/memory
Channel-/Channel+
CD:stop /BT pair
CD/BT: play/pause / Radio: auto search function
CB/BT: skip next / Tune+
CD/BT: skip previous / Tune-
Aux input jack
USB input
Speaker output connector
Headphone jack
DC power input
Antenna

audizio-102-326-Toulon-Micro-Hi-Fi-System-FIG-1

REMOTE CONTROL

ON/Standby
Numpad
Program
CD/USB previous K /Tuner down
Equalizer
X-Bass/ Pause/play
Repeat
BT mode: skip next track
BT mode: skip previous track M4
BT mode pairing
Source
Clock set
Timer
Sleep
Folder up/channel up
FM mode: mono/stereo
Enter
CD/USB next/ Tuner up
Folder down/channel down
Random/intro
Mute
BT mode: play/pause
Volume up/down
CD/USB mode: play/pause
CD stop

audizio-102-326-Toulon-Micro-Hi-Fi-System-FIG-2

TURNING THE UNIT ON/OFF

In standby mode, push POWER/STANDBY on the main unit or remote control to turn the unit ON. The unit will turn on, the last selected input mode icon will show on the LCD display.
To turn the unit OFF (into standby). push PoWER/STANDBY on the main unit or remote control again. The LCD DISPLAY will go dim and show the current time. The standby mode indicator lights.

SETTING THE CLOCK

After plugging the DC power adapter into the unit, “00:00” will appear and blink on the LCD display.

In Power Off (Standby) mode, press and hold CLOCK SET on the remote control or main unit, the 24-HOUR format “24H” will appear on display.
Press lork on the remote control or main unit to select 24 Hour format if desired. Otherwise, press CLOCK SET to confirm 12 Hour clock format and enter clock setup mode. Hour digits will be flashing.
Press OR on remote control or main unit to adjust the hour. Press and hold the button for fast advance/reverse setting Note: Make sure the hour is set so that the PM indicator is displayed correctly.
Press CLOCK SET on the remote control to confirm the hour setting, the minute digits will flash to prompt for input. Pressler Kon the remote control or main unit to adjust the minute. Press and hold the button for fast advance/reverse setting
Press CLOCK SET on the remote control again to complete the setting

NOTE: The clock and radio station presets will need to be reset if the power is interrupted or in the event of a power outage. 00:00″ will appear and start blinking on the LCD display to notify you that the power was interrupted and the clock will need to be reset. Please follow above steps 1-6 to reset the clock.

CHECKING THE CLOCK

The unit will show the current time in standby mode. To check the current time in Power ON mode, press CLOCK SET on main unit or remote control, the current time will show for 5 seconds and then return to the previous screen.

ALARM OPERATION

SETTING THE ALARM CLOCK
This function allows the system to turn on automatically and wake you using a beeping alarm, CD/USB/FM music or buzzer. Timer start time (ON):

Press and hold, in standby mode, the TIMER button on the remote control until the display shows “On”, and the hour digits flash.
Press the OR lbuttons to adjust the hour digits, and then press the ENTER button to confirm. The minute digits will flash on the display.
Press the or buttons to adjust the minute digits, and then press the ENTER button to confirm. Timer end time (OFF}:
When the “On” Timer Clock is set, the display will show “OFF” and the hour digits will flash.
Press the Kor b buttons to adjust the hour digits, and then press the ENTER button to confirm. The minute digits will flash on the display.
Press the 44orbHbuttons on the remote control to adjust the minute digits, and then press the ENTER button to confirm.
Press the k4or>lbuttons to select CD, USB, FM or BU (buzzer) mode, then press the ENTER button to confirm. The display will show “VOL#”.
Press the or lbuttons to adjust the volume, and then press the ENTER button to confirm.
Press the TIMER button to select “Timer On”, the Timer is set.
In standby mode, the icon “9 will show on the display to indicate the Timer is On.

NOTE:
If “Wake to CD/USB” is selected but a CD or USB drive are not inserted, the alarm will default to the Beeping Alarm automatically when the alarm time is reached. For Wake to Radio”, the system will default to the last FM radio station listened to prior to switching off. The crescendo alarm will increase to the volume level you have set.

ACTIVATE/DE-ACTIVATE ALARM FUNCTION

To activate the ALARM, press the TIMER button, and the alarm icon “ ” will show on the LCD display.
Cancel the ALARM function by pressing the TIMER button again. The alarm icon “ ” will disappear from the LCD display.

WAKE TO RADIO, CD/USB OR BUZzER ALARM

When the alarm time is reached, the CD/USB, radio or beeping alarm will sound for 60 minutes, then shut off and reset itself for the following day (without pressing the snooze button).
To stop the alarm immediately after it sounds, press the POWER button on remote control or on main unit once. It resets itself for the following day.
To cancel the following day alarm, tap the TIMER button once, the alarm icon “ ” will disappear from the LCD display.

RADIO OPERATION

Tap the POWER/STANDBY button on main unit or remote control to turn on the unit.
Tap the SOURCE button on main unit or remote control to select FM mode.
To manually tune to a specific radio station, tap the TUNE Kor>>lbutton on either main unit or remote control repeatedly. Use this manual tuning method to tune in to weaker stations that are bypassed by Automatic Tuning method.
To automatically tune to the next available radio station, press and hold the Korlbuttons on main unit or remote control for 1-2 seconds until “SCA” readout appears on the display, then release the button. The tuner will stop scanning when it receives the next broadcasting station of adequate signal strength.

5. Turn the volume control on main unit or press the volume buttons on remote control to adjust to the desired volume
level

FM/FM STEREO RECEPTION

When listening to the FM radio, press the ST./MONO button on remote control to switch between stereo mode and mono mode. The FM stereo icon “ST appears on the display when unit is set in stereo mode. It is preferable to receive the program in mono when you are receiving a weak station.
HINTS FOR BEST RECEPTION:
For best FM reception, the FM wire antenna located on the back of the unit should be fully unwrapped and extended.

NOTE: Automatic tuning depends on the signal strength of the broadcasting station, so weak stations may be skipped. You can manually tune to find the weak stations if a station gets skipped. With strong signals, the tuner may stop before it reaches the actual broadcast frequency, so you may need to manually tune for the best reception.

PRESET RADIO STATIONS

Press the POwER button on main unit or remote control to turn on the unit.
Press the SOURCE Button on main unit or remote control to select FM radio mode.
Press and hold the TUNE K4or TUNE or button on the main unit or remote control until “SCA” readout appears on the display. Release the button for auto search & program preset channels. Auto searching and program will stop at P01 af scan finished.
Note: If the channels stored during the auto search & program preset are not the ones you want to save, use the method below for manually saving radio presets.
Tune to the desired radio station either by “manually” or “automatically” tuning method.
Press the PROG. button on the remote control, the next available preset memory numb on the LCD display (Note: “P01” will show in the display if you are programming a preset for the first time).
Tap the CHANNEL -l+ buttons on main unit or remote control to select the preset number you want to assign the statior to.
Tap the PROG. button on the remote control to confirm the setting.
Repeat above steps 4-8 to preset up to 30 FM stations. nd a flashing number will sh RECALLING PRESET MEMORY CHANNELS In radio mode, recall the pre-set channels by pressing the CHANNEL -/+ buttons on main unit or the numbers on remote control.

RECALLING PRESET MEMORY CHANNELS

In radio mode, recall the pre-set channels by pressing the CHANNEL -/+ buttons on main unit or the numbers on remote control

IMPORTANT:
It may take up to 10 seconds for the actual playback to begin. If playback does not start at all, it is possibly due to the quality of the CD-R/RW, MP3 disc and/or the compatibility of the CD compilation software. The manufacturer is not responsible for the playback quality of CD-R/RW, MP3 discs. Do not stick a label to either side of the disc. lt may cause a serious malfunction.

PLAYING CD

Press the POWER/STANDBY button on main unit or remote control to turn the unit on.
Press the SOURCE button on remote control or main unit to select CD mode and press “Open/close disc compartment” (on top of the compartment lid).
Place a CD on the center spindle with its label side facing out towards the CD lid. Close the disc compartment.
The unit starts to read the disc, “.-” flashes on the display. After a few seconds, the total number of tracks show on the LCD display.
Press the PLAY/PAUSE button on main unit or remote control, PLAY indicator shows on the display, the CD will start playing the first track.
Turn the volume control on main unit or press the volume control buttons on the remote control to adjust to the desired volume level
To pause playback, press the PLAY/PAUSE button on main unit or remote control. The track time will be paused and the play indicatorwill blink on the display. To resume playing , press the PLAY/PAUSE button again.
You can choose to play your favorite track by pressing the SKIP NEXT Ibutton or SKIP PREViOUS 4 button. The LCDdisplay will indicate the current track number.
To locate a particular section within a track, press and hold the Mor lbutton until the section is found. Release the button to continue playing your selection.
To stoP playing, press the STOP button.

PLAYING CD-R/RW, MP3 WITH FOLDER

Press the SOURCE button on the remote control, and load an MP3 disc.
Press the FOLDER -/+ button to select desired playback folder.
Select the desired file to be played by pressing the SKIP NEXT lor SKIP PREVIOUS button.
Press the PLAY/PAUSE button. Playback will start and the file name will be displayed.

In case of playback with the folder mode on, press the FOLDER -/+ buttons, and the folder can be selected even though it is in playback/pause mode. It will continue playback/pause mode in the 1st track of the selected folder.

TO PLAY BACK USB/MP3 PLAYER WITH FOLDER

Press the SoURCE button on the remote control or on the main unit to select the USB function. Connect the USB memory device that contains playable MP3 format files. When the USB memory is connected to the main unit, the device information will be displayed.
Press the FOLDER -/+ button to select desired playback folder.
Select desired file to be played back by pressing the K4orblbutton.
Press the PAUSE/PLAY button. Playback will start and the file name willbe displayed,

NOTE
This product is not compatible with MTP and AAC file systems from USB mass storage devices or MP3 players This unit supports FAT16 and FAT32, but some USB storage media may not supPport both file systems. For details, refer to the operation manual of the USB storage device in question or contact the manufacturer.

SKIP AND SEARCH MODE

During playback or pause mode, press the SKIP NEXT lor SKlP PREVIOUS button to go to the next track or go back to the beginning of the current track.
During playback, press and hold the>lorH4button to search within the current track with audible high speed playback.

PLAY MODE SETTINGS

NOTE: The following is only functional by using the remote control.

Press the REPEAT button on the remote control to select different repeat play modes when a CD is playing:

REPEAT 1- the track currently playing will repeat continuously. “REPEAT 1” appears on the display.
REPEAT ALL – all tracks will repeat continuously. “REPEAT ALL” appears on the display.

RANDOM PLAY

When the RANDOM/INTRO button is pressed, the “RAND” indicator will appear on the LCD display. The tracks on the disc willV be played in random order automatically. Cancel Random Play: Press RANDOM/INTRO Uuntil the “RAND” indicator disappears.
NOTE:
Pressing the button during random play will initiate a skip to the track selected next by random operation. On the other hand, the button does not allow you to select the previous track.

INTRO PLAYBACK

Press RANDOM/INTRO on the remote control. The “INTRO” indicator will appear on the display. The unit will play only the first 10 seconds of each track (intro).
Press RANDOM/INTRO on the remote control again to resume normal playback.

PLAY TRACH SEQUENCE PROGRAMMING
NOTE : The following is only functional by using the remote control This function allows the tracks to be played in a programmed sequence. The user can program up to 32 tracks in CD mode or 99 tracks in MP3 mode. This program can only be set in STOP mode.

Press the PROG. button on the remote control, “P01” and “PROG appear on the display (“PO1” will be shown if you are programming for the first time).
Use the>lork button on the main unit or the remote control to select the desired track. The track number will appear on the display.
Press the PROG. button on the remote control to store the selected track in the memory, the program number will advance one (i.e.”P02″) on the display.
Repeat steps 2 to 3 to store more tracks. You can store up to 32 CD tracks or 99 MP3 tracks. Display will show “FUL” after tracks have been programmed and memory is full.
Press PAUSE/PLAY on the main unit or the remote control to start playing the CD in the programmed sequence
Press the REPEAT button on remote control to select Repeat 1/A if desired.
To stop play, press the STOP button on the main unit or on the remote control.
To cancel the program altogether, press the STOP button on main unit or remote control twice. The “PROG” icon will disappear from the display.

BT OPERATION

Press the POWER/STANDBY button to turn ON the unit, follow the instructions below to connect with BT. Pairing a BT streaming capable smartphone (or other BT capable device) to the Audizio Toulon:

Press the POWER/STANDBY button on the main unit or the remote control to turn on the unit.
Press the SOURCE button on the main unit or remote control to select BT mode, “bt” blinks on the display.
Turn on the BT streaming function of your BT capable device and enable the search or scan function to find the Audizio Toulon. Select “Audizio Toulon” from the device list when it appears on your devices’ screen. If required, enter the pass code 0000″ to pair.
After successfully pairing device and Toulon, the display will show “bt” continuously (the blinking has stopped). You can begin playing music from your device wirelessly.
After selecting your favorite song, press the PLAY/PAUSE button on the main unit or on the remote control to play or pause the song.
Turn the volume control on the main unit or press the volume buttons on the remote control to adjust to the desired volume level.
Press the K4or>lbutton on the main unit or on the remote control to skip to previous or next song.
If you want to pair the Audizio Toulon with another BT enabled device, press and hold the PAIR Button for 3 seconds or turn off thee BT function of device currently paired with Audizio Toulon then repeat the steps above.

PRESET EQ

NOTE: The following is only functional by using the remote control. This unit provides 4 different EQ modes to enhance your listening experience. You can select the desired effect by pressing the EQ Button on remote control at the following sequence

MUTE

NOTE: The following is only functional by using the remote control. Press the MUTE button on the remote control to mute the sound output from the speaker. “V 00” will appear on the display. Press the MUTE button again to resume to speaker playback.

SLEEP

NOTE: The following is only functional by using the remote control. The sleep timer allows you to turn the unit off automatically after a preset time is reached.

To activate the sleep timer, turn the unit on and press the SOURCE button to select FM radio, CD, USB, BT or AUX IN.
Press the SLEEP button on the remote control, “SLEEP” appears on the display.
Repeatedly press the SLEEP button to select a sleep time. The unit will turn off after 10, 20, 30, 40, 50, 60, 70, 80 or 90 minutes. Wait for 3 seconds after your selection for the unit to confirm the selection, the unit will play for the selected length of time then automatically shut down.
To cancel the sleep timer, press the SLEEP button repeatedly until the timer on the display shows “OFF”, the sleep time icon “SLEEP” disappears from the display. To turn the unit off before the selected length of time, press the POWER/STANDBY button at any time. NOTE: To check the remaining sleep time, press the SLEEP button once. If you are falling asleep to music from an external device connected to the AUX input, the sleep timer will shut off the power to this system but it will not turn off the external device.

NOTE: To check the remaining sleep time, press the SLEEP button once. If you are falling asleep to music from an external device connected to the AUX input, the sleep timer will shut off the power to this system but it will not turn off the external device.

USING THE AUXILIARY INPUT

NOTE: AUX cable is not supplied. You can use the auxiliary input jack to connect an external playback device (for example a CD player or MP3 player). Press the SOURCE button until you see “AUX” appearing on the display. Plug the end of a 3.5 mm jack- 3.5 mm jack cable into the AUX IN socket on the front panel. Connect the other end of the cable to your external device. Switch on your external device and choose your favorite soundfile.