BOSCH NETP669SUC 36 Inch Electric Smoothtop Cooktop Instruction Manual

: June 3, 2024
: Bosch

BOSCH NETP669SUC 36 Inch Electric Smoothtop Cooktop

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

Read all instructions carefully before use. These precautions will reduce the risk of electrical shock, fire and injury to persons. When using kitchen appliances, basic safety precautions must be followed including those in the follow-ing pages.

Safety definitions

Here you can find explanations of the safety signal words used in this manual.
WARNING
This indicates that death or serious injuries may occur as a result of non- observance of this warning.
CAUTION
This indicates that minor or moderate injuries may occur as a result of non- observance of this warning.
NOTICE:
This indicates that damage to the appliance or property may occur as a result of non-compliance with this advi-sory.
Note: This alerts you to important information and/or tips.

General information

Read this manual carefully.
Keep the instructions, the appliance pass and the prod-
uct information safe for future reference or for the next owner.
Do not connect the appliance if it has been damaged in

General safety instructions

IMPORTANT: SAVE THESE INSTRUCTIONS FOR THE LOCAL ELECTRICAL INSPECTOR’S USE.
OWNER: PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
INSTALLER: LEAVE THESE INSTRUCTIONS WITH THE APPLIANCE AFTER INSTALLATION IS COM-PLETE.
WARNING
If the information in this manual is not followed exactly, fire or shock may result causing property damage or personal injury. Do not repair, replace or remove any part of the appliance unless specifically recommended in the manuals. Im-proper installation, service or maintenance can cause in-jury or property damage.

▶ Refer to this manual for guidance.
▶ All other servicing should be done by an authorized ser-vice provider.

When installing a cooktop over a single oven, be sure to follow the instructions in both the oven’s and the cooktop’s installation manuals.

You can find a list of approved combinations of cooktop and oven in the Approved Combination Matrix of your cooktop, or you can contact Customer Service for the latest list of approved combinations. Do not try to install your cooktop over any oven that is not stated in that list.

DO NOT install any refrigerators, dishwashers, ovens
(without ventilation), or washing machines below the cook-top. Refer to the Approved Combination Matrix.
Never modify or alter the construction of the appliance. The appliance should only be used if installed by a quali-fied technician in accordance with these installation in-structions. The manufacturer is not responsible for any damage resulting from incorrect installation.
To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space located above the surface units should be avoided.

If cabinet storage is to be provided, the risk can be reduced by installing a hood that projects horizontally a minimum of 5″ (127 mm) beyond the bottom of the cabinet.
Verify that cabinets above the cooktop are a maximum of 13″ (330 mm) deep.

NOTICE:
We strongly recommend the installation of a ventilation system with this appliance.
WARNING
Remove all tape and packaging before using the appli-ance.

Destroy the packaging after unpacking the appliance.
Dispose of packaging in an environmentally responsible manner.
Never allow children to play with packaging material.

Appliance handling safety

WARNING

Hidden surfaces may have sharp edges.
Use caution when reaching behind or under appliance.

Safety codes and standards

This appliance complies with the latest version of one or more of the following standards:

UL 858 – Household Electric Ranges
CAN/CSA-C22.2 No. 60335-1 – Safety of Household and Similar Electrical Appliances – General
CAN/CSA-E60335-2-6, The Standard for the Safety of
Household and similar electrical appliances.
It is the responsibility of the owner and the installer to de-termine if additional requirements and/or standards apply to specific installations.

Electrical safety

Installer – show the owner the location of the circuit breaker or fuse. Mark it for easy reference.
If required by the National Electrical Code (or Canadian Electrical Code), this appliance must be installed on a separate branch circuit.
Local codes vary. The installer is responsible for ensuring that the installation, connections, and grounding comply with all applicable codes. The manufacturer is not responsible for any issues associated with the improper installation of this product.
The circuit breaker must be in accordance with the National Electrical Code (or Canadian Electrical Code). ¡ Be sure your appliance is properly installed and grounded by a qualified technician. Installation, electrical connections and grounding must comply with all ap-plicable codes.
Refer to the rating plate for more information. “Rating plate location”, Page 8

WARNING
Before installing, turn power OFF at the service panel.

Lock service panel to prevent power from being turned ON accidentally.

To be able to disconnect the appliance from the power supply, there must be a means of contact separation, e.g. a circuit breaker, on all poles, in accordance to local wiring codes.
GROUNDING INSTRUCTIONS

This appliance must be grounded.
Grounding reduces the risk of electric shock by providing a safe pathway for electric current in the event of a short circuit.
Be sure your appliance is properly installed and grounded by a qualified technician.
Installation, electrical connections and grounding must comply with all applicable codes.

Before you turn on power supply, make sure all controls are in the OFF position.

State of California Proposition 65

This product may contain a chemical known to the State of California, which can cause cancer or reproductive harm. Therefore, the packaging of your product may bear the following label as required by California:

Before you begin

friRead these instructions before you begin to install your appliance.

Parts included

After unpacking all the parts, check for any damage in transit and for completeness of delivery.

Tools and parts needed

Prepare these tools and accessories before you start to in-stall your appliance.

Pencil
Measuring tape
Cross head screwdriver
Drill with bit 1/4″ (6 mm)
Jigsaw
Note: Additional materials may be necessary for installation in solid surface countertops. Contact the countertop manufacturer.

Cabinet requirements

Ensure that the cabinetry at the installation location meets the requirements for a safe installation.

The distance from the top of the cooktop to the bottom of cabinets above must be a minimum of A=30″ (762 mm).
This distance can be reduced to A=24″ (610 mm) when the bottom of the wood or metal cabinet is protected by not less than ¼” (6.35 mm) flame-retardant millboard covered with not less than no. 28 gauge sheet metal, 0.015″ (0.4 mm) stainless steel, 0.024″ (0.6 mm) alu-minum or 0.020″ (0.5 mm) copper.
Verify that unprotected cabinets above the cooktop are a maximum of B=13″ (330 mm) deep.

Installation of a cooktop over ovens and microwaves
Only certain models may be installed over an oven or a microwave. Verify the Approved Combination Guide sup-plied with these instructions for approved installation combinations. Both products will have a label stating Approved Combination Guide.
Installation of a range hood or a microwave hood above the cooktop
Follow the range hood or microwave hood installation instructions for dimensional clearance above the cooktop surface.

Countertop requirements

Ensure that the countertop into which the cooktop is to be installed meets these requirements for a safe installation.
WARNING

To reduce the risk of ignition of surrounding combustible materials, install at least 3″ (76 mm) from both sidewalls and at least 2″ (51 mm) from the rear wall.
The countertop must be level and horizontal.
The stability of the countertop must be maintained after the cut-out has been made.
Solid surface countertops often require special installations. For example, heat-reflective tape and rounded corners may be necessary.
Contact the countertop manufacturer for instructions

Prepare installation space
Create the cutout in the countertop according to the instructions.
General countertop requirements:
¡ The angle of the cut surface to the countertop must be
90°.
¡ With multi-layered countertops, secure strips laterally in
the cutout if necessary.
¡ After creating the cutout, remove all shavings.
¡ Seal the cut surfaces in a heat- and water-resistant
manner.
¡ Observe the minimum distance between device under

Cutout dimensions for 30″ cooktops

Refer to these measurements for the models stated here. ¡ NET8069SUC

NET8069UC
NETP069SUC
NEM5066UC

Cutout dimensions for 36″ cooktops

Refer to these measurements for the models stated here. ¡ NET8669SUC

NET8669UC
NETP669SUC
NEM5666UC

Installation procedure

Follow these instructions to install the cooktop into the countertop.
CAUTION Sharp edges.
CAUTION
The appliance is heavy.
It is recommended that two people install this appliance.

Securing the cooktop in the countertop

The cooktop should be secured to the countertop using the brackets provided.

Attach the brackets to the corresponding slots on the underside of the cooktop.
Place the cooktop into the countertop cutout.
Insert the clamping screws into the bracket and secure the cooktop to the countertop. Protect delicate counter-tops by placing a wooden disk underneath.

Electical connection

Read these instructions to safely connect your appliance to the electrical supply.
5.1 Electrical requirements
Ensure that the following general requirements are met. ¡ You can find the rating plate with the electrical specificooktop connection. It should be easily accessible for service purposes.

Power supply

Model 240 V AC, 60 Hz system: circuit breaker
208 V AC, 60 Hz system: circuit breaker
NET8069SUC 40 Amp 30 Amp
NET8069UC 40 Amp 30 Amp
NET8669SUC 50 Amp 40 Amp
NET8669UC 50 Amp 40 Amp
NETP069SUC 40 Amp 40 Amp
NETP669SUC 40 Amp 40 Amp
NEM5066UC 30 Amp 30 Amp
NEM5666UC 40 Amp 40 Amp

Connecting electrical supply

WARNING
Before installing, turn power OFF at the service panel.
To reduce the risk of electrical shock and fire, do not use a flexible power- supply cord with this appliance. Connect only to a 3-wire, 120/240-Volt power supply; the neutral conductor is not required for the operation of the appli- ance. The voltage at the power supply electrical connec-tions shall be 150 -volts-to-ground or less.
Requirement: The electrical power supply system should be a 1-phase, 3-wire system with ground connection.

Install a suitable junction box (not furnished).
An appropriately-sized, UL-listed conduit connector must be used to correctly attach the conduit to the junction box.
The branch-circuit breakers ampacity, the wire sizes and the connections must conform to the require-ments of the National Electrical Code or Canadian Electrical Code and all local codes and ordinances.
Attach the flexible conduit to the junction box. Metal conduit and leads are factory installed.
Connect the cooktop lead wires to the junction box supply wires in proper phase.

black (L1) to black
red (L2) to red
green or blank copper wire to ground

Checking the installation

Check if your unit is working properly after you have com-pleted the installation steps.
WARNING
Before you turn on power supply, make sure all controls are in the OFF position.

Remove everything from the cooktop surface including stickers.
Clean the cooktop surface with cooktop cleaning cream.
Switch on the circuit breaker.
Verify that all cooking zones function properly.

Customer Service

If you have any questions on use, are unable to eliminate an issue in the appliance yourself, or the appliance needs to be repaired, please contact our Customer Service. With any warranty repair, we will make sure your appli-ance is repaired by an authorized service provider using genuine replacement parts. We use only genuine replace-ment parts for all repairs.
Detailed information on the warranty period and terms of warranty can be found in the Statement of Limited Product Warranty, from your retailer, or on our website.
If you contact the Customer Service, you will need the model number (E-Nr.) and the production number (FD) of your appliance.
USA:
1-800-944-2904
www.bosch-home.com/us/owner-support/get-support
www.bosch-home.com/us/shop
CA:
1-800-944-2904
www.bosch-home.ca/en/service/get-support
www.bosch-home.ca/en/service/cleaners-and-accessories

Model number (E-Nr.) and production

You can find the model number (E-Nr.) and the production number (FD) on the appliance’s rating plate.
Making a note of your appliance’s details and the Cus-tomer Service telephone number will enable you to find them again quickly.
7.2â€€Rating plate location
You can find the rating plate of your appliance:
Â¡ on the underside of the appliance
Â¡ in the appliance pass