gofanco HDsplit8K-2P 2 Port HDMI Splitter User Guide

gofanco HDsplit8K-2P 2 Port HDMI Splitter

Thank you

Thank you for purchasing from gofanco. Our products aim to meet all your connectivity needs wherever you go. For optimum performance and safety, please read the instructions carefully and keep this User’s Guide for future reference. If you need more information about our products, please visit www.gofanco.com. For technical support, please email us at support@gofanco.com. For drivers and manuals download, please go to www.gofanco.com/downloads.

Important Safety Notices

Please read safety instructions carefully before installation and operation.

• Please pay close attention to all warnings and hints for this device
• Do not expose this unit to rain, heavy moisture, or liquid
• Do not repair the device or open the enclosure without professional guidance to avoid electric shocks. Doing so may void your warranty
• Keep the product in a well-ventilated location to avoid damage from overheating
• Shut off power and make sure environment is safe before installation
• Do not plug the HDMI cables in/out when the device is in use to avoid cable damage. Make sure they are plugged into the correct ports

Package Contents

• 2-Port 8K60Hz HDMI Splitter
• USB-C to USB-A power cable
• User’s guide

Introduction

The 2-Port 8K60Hz HDMI Splitter distributes HDMI video and audio from a single source to 2 HDMI displays simultaneously.

Features

• Supports 8K @60Hz YUV 4:4:4, 4K @120Hz, 4K @144Hz (via EDID copy), 1080p @240Hz

• HDCP 2.3/2.2/1.4 compliant

• Audio: Uncompressed LPCM and compressed DTS and Dolby Digital audio (including DTS-HD Master and Dolby True HD)

• EDID modes: Auto, copy, downscale. With an 8K input, downscaling allows mixed 8K and 4K (or 1080p) displays to operate in their native resolutions

• Supports HDR10, HDR 10+, Dolby Vision via video pass-through (EDID copy)

• Supports CEC (output 1 only), VRR, and ALLM.
  Note: For VRR/ALLM support, we recommend that both output monitors/TVs are of the same make/model and they support VRR/ALLM

• USB bus-powered

Installation Requirements

• HDMI source device (computer, DVD player, XBOX, PS3, etc)
• HDMI display devices (SDTV/Monitor, HDTV/ Monitor, projector, etc.)

Product Layout

Figure 1: Front and Rear Panel Layout

1. Power LED: On when the splitter is powered on
2. Output (1-2) LED: On when displays are detected
3. Auto EDID Mode LED: When on, the EDID of the display with the lowest capabilities is transmitted to both displays – see EDID Management on page 7 for more information
4. Copy EDID Mode LED: When on, the EDID of the display connected to Output 1 is the default for both outputs – see EDID Management on page 7 for more information
5. Downscale EDID Mode LED: When on, the splitter will automatically downscale an 8K source signal to 4K or 1080p displays – see EDID Management on page 7 for more information
6. EDID Mode Selection Button: Press to select Auto, Copy, Downscale EDID mode in sequence
7. Power Jack (USB-C): Connects to the included USB Type-C to Type-A power cable
8. HDMI In: Connect to your HDMI source device
9. Outputs (1-2): Connect to your HDMI displays

Hardware Installation

1. Power off all devices including your HDMI source and HDMI displays.
2. Connect your HDMI source device to the HDMI In connector with an HDMI cable (HDMI cable not included).
3. Connect your HDMI displays to the Output (1-2) connectors with HDMI cables (HDMI cables not included).
4. Plug the included USB power cable into the splitter’s power jack then plug the other end into a USB 3.0 port or 5V/1A wall charger.
5. Power on all connected devices.
6. The 8K HDMI splitter is ready for use.

Note: Please use the latest HDMI 2.1 or later cables for best performance.

Connection Diagram

Figure 2: Connection Diagram

EDID Management

Press the EDID button on the front panel to switch between the three EDID modes.

Auto EDID

• Reads the EDID of each display and uses lowest resolution and audio format for both displays
• This is the default EDID mode
• When the splitter is powered Off/On it returns to Auto EDID mode

Copy EDID

• Copies EDID of the monitor connected to Output 1
• Supports downscaling from 8K to 4K or 1080p on HDMI Output 2

Note:

• Supports 4K @120Hz and 4K @144Hz outputs

Downscale EDID

• Maximum resolution: 8K @60Hz YUV 4:2:0
• EDID of monitor on Output 1 is sent to Output 2, and downscaled accordingly
• Supports downscaling from 8K to 4K or 1080p on HDMI Output 2

Note:

• ONLY supports 2ch audio with Downscale EDID mode

Specifications

1080i@50/60Hz

Resolution (Proiv0e)

| 480p@50 /60Hz, 576p@50/60Hz,
7l0p@50/60Hz, l(B)p@50/60Hz,
4K@’24/30/50 I ro I 120Hz,
8K@24/30/50/60Hz
Operating Temperature| 32 to 158 F (0 to 7q0
Storage Humidity| 5%1to 90°/o RH, non-condensing
Power| USB Power Cable, 5V/IA
Power Consumption (Max)| 5W
Dimensions (LxWxH)| 3.6″xl.7”:x0.14″ (90x44x14 mm)
Weight| 0.21b (87g)

Disclaimer

The product name and brand name may be registered trademarks of related manufacturers. TM and ® may be omitted on the user’s guide. The pictures on the user’s guide are just for reference, and there may be some slight differences with the actual products.
We reserve the rights to make changes without prior notice to a product or system described herein to improve reliability, function, or design.

Customer Support

Thank you for choosing gofanco
www.gofanco.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>