SystemQ SEE705 NiteDevil 24C Camera Instruction Manual
- June 4, 2024
- SystemQ
Table of Contents
SEE705 NiteDevil 24C Camera
Instruction Manual
NiteDevil 24C Camera SEE705
5MP Eyeball 2.8mm Built In Mic
© 2022 System Q Ltd
NiteDevil.com
xSEE705
Table of Contents
Part 1 Introduction
1
1 SEE705 ……………………………………………………………………………………………………………. 1
Part 2 Tools & Handy Extras
1
Part 3 Connections
2
Part 4 4-In-1 Technology
2
Part 5 OSD Menu
3
1 5MP OSD Menu ………………………………………………………………………………………………… 4 2 Key Menu Settings ……………………………………………………………………………………………. 5
Part 6 Audio Over COAX
6
Part 7 Troubleshooting
7
1 Camera Rebooting / Turning Off …………………………………………………………………………. 7 2 Poor Quality Images …………………………………………………………………………………………. 7 3 Image is Black & White …………………………………………………………………………………….. 7 4 NCD / No Image Displayed on Recorder ………………………………………………………………. 7
Part 8 General Maintenance
8
Part 9 Specification
9
1 SEE705 ……………………………………………………………………………………………………………. 9
Part 10 Conditions
10
1 General Company Disclaimer …………………………………………………………………………… 10 2 WEEE Declaration …………………………………………………………………………………………… 10 3 Copyright ………………………………………………………………………………………………………. 10
Index
11
© 2022 System Q Ltd
I
NiteDevil.com
Introduction
Introduction
1.1 SEE705
The all new NiteDevil® 24C can stay in full colour around the clock using the
minimal amount of natural light to produce superb full colour images. It
really is a game changer in performance and should be used as a part of any
CCTV system requiring full colour images in key areas around entrances etc.
With built in dual IR and white light you can choose how the camera best works
in your install. Using white light to give visual warning or using IR
illumination to get a more discreet set up. A built in microphone means you
can see and hear what’s happening, recording the audio & video on your ZIP
SUPA-S DVR for the best possible CCTV evidence.
Tools & Handy Extras
Screwdriver Drill 12V DC PSU Drill bits BNC Crimp Tool & BNCs RG59 Coax Cable
Digital Multi-Meter LCD400K – CCTV Test monitor
© 2022 System Q Ltd
NiteDevil.com
1
xSEE705
Connections
The camera has a 2.1mm socket which requires 12V DC, use a regulated power
supply rated above the current draw of the camera. The camera is polarity
sensitive so connections must be correctly made. The camera has a standard BNC
connector for video output, the output can be changed to AHD, CVI or CVBS if
required in the menu
4-In-1 Technology
Selectable HD-TVI, HD-CVI, AHD and CVBS (Analogue) Output. As default the
camera is set to HD-TVI, however the output can be changed to AHD, CVI or CVBS
if required. This output can be changed with in the menu camera. Please note
the “Mode” in the menu of the DVR won’t change the format, as the menu
overrides the output. See OSD Menu 3 for accessing and changing the video
format.
31/03/2022
2
NiteDevil.com
OSD Menu
OSD Menu
Access to the camera menu is by Coaxitron. For the ZIP DVRs, ZIP Coaxitron is
set as default. To access the Cameras Menu via coaxitron:-
1. Click on the image in Live view 2. Click on the PTZ button at the bottom
of the screen 3. Click on the IRIS + / centre button to display the menu
Use the directional arrows to move up and down through the menu. Use the
directional arrows left and right to change the option. Use IRIS + to select &
enter that menu option.
© 2022 System Q Ltd
NiteDevil.com
3
xSEE705
5.1 5MP OSD Menu
Video Mode Format Language Exposure
Day & Night
Video Settings
Volume Reset Exit Save Exit
TVI / AHD / CVI / CVBS
5M20 / 4M25 / 4M30 / 2M25 / 2M30
English / Spanish / French / Chinese
Exposure Mode
Global
AGC
High / Middle / Low
Back
Exit
Save Exit
Mode
Ext / Color / B/W
Dim
0 3 (3 Default)
Back
Exit
Save Exit
AWB
Auto
Brightness
1 -9 (5 Default)
Contrast
1 -9 (5 Default)
Sharpness
1 -9 (5 Default)
Saturation
1 -9 (5 Default)
NR
1 -9 (5 Default)
Mirror
Default / Mirror / Flip / Rotate
Back
Exit
Save Exit
0 9 (9 Default)
31/03/2022
4
NiteDevil.com
OSD Menu
5.2 Key Menu Settings
Exposure Mode – AUTO / GLOBE / GLOBAL sets the required shutter speed for the
current light level. The shutter speed will automatically detect the required
length of time to keep the digital sensor exposed to light. FLK option sets
the shutter speed to stop synchronisation with lighting so that pulsing effect
is minimised.
White Balance – Colour adjustment of the camera to be set up so objects appear
a natural colour. ATW / PRO (Automatic tracking white balance) continually
tracks and adjusts the white balance, making it suitable for use in cameras in
which the image content and lighting are subject to changes.
Day & Night – The camera can be set to colour or B&W mode or have it
automatically switch External is set as default, the switch between colour and
black & white is controlled by an external trigger In this a light dependent
resistor.
DNR (Noice Reduction) – Noise Reduction is the process of removing noise from
the video signal by applying a digital filter. 2D noise reduction reduces
noise in the foreground of the image where as 3D noise reduction reduces noise
in both the foreground and the background of the image.
D-WDR – Digitally adjusts the exposure in areas of the frame to maintain
optimum levels in both the dark and bright areas of an image. NOTE – Some
models may not have D-WDR function.
Reset – Defaults the camera to factory settings. This setting helps when fault
finding issues with the camera to ensure all settings are defaulted.
© 2022 System Q Ltd
NiteDevil.com
5
xSEE705
Audio Over COAX
As of writing this (March 2022), the Audio over COAX (Coaxial Audio) is
compatible with the ZIP SUPA-S range of recorders. *Note the standard SUPA
recorders are not compatible with Audio over COAX. To enable, in the menu on
the SUPA-S go to System > General > Audio Input Type Select Coaxial Audio
Select Apply
31/03/2022
6
NiteDevil.com
Troubleshooting
Troubleshooting
7.1 Camera Rebooting / Turning Off
A. Check the voltage to the camera (under load) using a digital multi-meter,
if below 10.8V then move the power supply closer to the camera.
B. For 12V DC cameras, only use regulated power supply rated above the current
consumption, so that the camera is always receiving the correct supply which
is rated above the current consumption.
C. Use thicker gauge copper cabling to reduce the voltage drop to the camera,
using thicker cable will reduce the resistance between the camera and the
power supply and therefore reduce the voltage dropped along the cable.
7.2 Poor Quality Images
A. Check the video format the DVR (digital video recorder), then set the
camera to the relevant video format see the 4-In-1 Technology 2
B. If set to CVBS, then this is a low quality video output for legacy systems
(analogue – CVBS), when using a 2 MegaPixel DVR or above then use another
video format, like HD-TVI.
C. Reset the camera menu via Zip Coaxitron OSD Menu 3
D. Check if the DVR (digital video recorder) supports the resolution of the
camera.
7.3 Image is Black & White
A. Check the video format your DVR supports, then set the camera to the
relevant video format see the 4-In-1 Technology 2
B. Reset the camera menu via Zip Coaxitron OSD Menu 3
D. Check if the DVR (digital video recorder) supports the resolution of the
camera.
7.4 NCD / No Image Displayed on Recorder
A. Check the voltage to the camera (under load) using a digital multi-meter,
if below 10.8V then move the power supply closer to the camera.
B. For 12V DC cameras, only use regulated power supply rated above the current
consumption, so that the camera is always receiving the correct supply which
is rated above the current consumption.
© 2022 System Q Ltd
NiteDevil.com
7
xSEE705
C. Use thicker gauge copper cabling to reduce the voltage drop to the camera,
using thicker cable will reduce the resistance between the camera and the
power supply and therefore reduce the voltage dropped along the cable. D.
Ensure that the BNC BNC lead that is connected between the camera and DVR
has no shorts between the ground and the centre core (positive) or open
circuits along the centre core (positive) or open circuits along the ground.
General Maintenance
Routinely clean the camera to prevent dust build up as this can effect the
performance of the camera. It is recommended to use a damp non-abrasive
microfibre cloth. Routinely check the connections for power and data to ensure
no water ingress and corrosion. Check that the cameras are firmly attached to
the wall or mounting bracket. Check playback in the recorder to ensure the
camera is recording and triggering properly.
31/03/2022
8
NiteDevil.com
Specification
9.1 SEE705
Resolution Lens Type Image Output Min.Illumination Day/Night InfraRed LEDs IR
Range Audio Input Voltage Current Consumption IP Rating Video Connection Power
Connection Finish Build Dimensions
Specification
5MP 2.8mm Fixed Lens 1 Volt Peak-Peak 75 ohm
0 Lux IR On 24C / Mechanical IR (True Day-Night)
2 White LEDs / 2 IR LEDs 20M
Built In Mic (Audio over COAX) 12V DC
300mA (IR On) IP66
BNC Socket 2.1mm DC Socket
White/ Black Metal
100mm (Diameter) x 90 mm (Height)
© 2022 System Q Ltd
NiteDevil.com
9
xSEE705
Conditions
10.1 General Company Disclaimer
All specifications are approximate. System Q Ltd reserves the right to change
any product specifications or features without notice. Whilst every effort is
made to ensure that these instructions are complete and accurate, System Q Ltd
cannot be held responsible in any way for any losses, no matter how they
arise, from errors or omissions in these instructions, or the performance or
non-performance of the equipment that these instructions refer to.
10.2 WEEE Declaration
This symbol on the products and/or accompanying documents means that used
electronic equipment must not be mixed with general household waste. For
treatment, recovery and recycling please return this unit to your trade
supplier or local designated WEE/CG0783SS collection point as defined by your
local council.
10.3 Copyright
© Copyright 2022 Zip is a registered trademark of System Q Ltd, Chesterfield.
Derbyshire. S40 2WB
31/03/2022
10
NiteDevil.com
Index
– A –
Adjustment 3
– C –
Cleaning 8 Connections 8 Copyright 10
– D –
Declaration 10 Dimensions 9 Disclamer 10
– G –
General Disclaimer 10
– H –
Handy Extras 1
– M –
Maintenance 8
– O –
OSD Menu 3
– S –
Settings 3 Specification 9
– T –
Tools 1 Troubleshooting 7
© 2022 System Q Ltd
– V –
Video Loss 7 Voltage drop 7
– W –
WEEE Declaration 10
NiteDevil.com
Index 11
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>