Satel SPP-110 Conventional Fire Alarm Sounder Instruction Manual
- September 28, 2024
- Satel
Table of Contents
SPP-110 Conventional Fire Alarm Sounder
“`html
Specifications:
- Product: Conventional fire alarm sounder SPP-110 EN
- Firmware version: 1.00
- Manufacturer: SATEL
- Designed for use with SATEL fire alarm control panels
(conventional: CSP-104, CSP-108, CSP-204, CSP-208; addressable:
ACSP-402)
Product Usage Instructions:
1. Installation:
-
Disconnect power before making any electrical connections.
-
The sounder is designed for installation indoors, in spaces
with normal air humidity. -
Turn the cover counter-clockwise and remove it.
-
Drill the holes for screws in the enclosure base. Use the
provided screws to fasten the base to the wall. -
Drill a hole for cables in the enclosure base.
-
Place the enclosure base against the wall and mark the mounting
hole locations. -
Drill holes for wall plugs (screw anchors) in the wall.
-
Run the cables inside the enclosure base.
-
Secure the enclosure base to the wall using wall plugs and
screws. -
Use DIP switches to configure the sounder settings (refer to
Configuring the sounder settings). -
Connect the zone circuit wires to the sounder. If it’s at the
end of a line, attach a 10k resistor to its terminals. -
Replace the cover and lock it with a screw.
2. Configuring the sounder settings:
Use the DIP switches on the electronics board to configure the
sounder settings. Follow the instructions provided in the user
manual to select the desired tone and supply voltage.
FAQ:
Q: Can I use the SPP-110 sounder outdoors?
A: No, the sounder is designed for indoor use only in spaces
with normal air humidity.
Q: How do I know which tone to select for acoustic
signaling?
A: Refer to Table 1 in the user manual that provides a list of
tones and their corresponding switch settings on the electronics
board.
“`
Conventional fire alarm sounder
SPP-110 EN
Firmware version 1.00
spp-110_en 04/24 SATEL sp. z o.o. · ul. Budowlanych 66 · 80-298 Gdask · POLAND
tel. +48 58 320 94 00
www.satel.pl
IMPORTANT
The device should be installed by qualified personnel. Prior to installation,
please read carefully this manual in order to avoid mistakes that can lead to
malfunction or even damage to the equipment. Disconnect power before making
any electrical connections. Changes, modifications or repairs not authorized
by the manufacturer shall void your rights under the warranty.
The following symbols may be used in this manual: – note, – caution.
The SPP-110 sounder is used for acoustic alarm signaling. The sounder is
designed to work with the SATEL fire alarm control panels (conventional:
CSP-104, CSP-108, CSP-204, CSP-208; addressable: ACSP-402).
1. Features
· Acoustic signaling by means of piezoelectric transducer. · 32 selectable
tones. · Selectable volume level.
2. Installation
Disconnect power before making any electrical connections. The sounder is
designed for installation indoors, in spaces with normal air humidity. 1. Turn
the cover counter-clockwise and remove it (Fig. 1). 2. Drill the holes for
screws in the enclosure base. Use the countersunk screws (Fig. 2)
or the non-countersunk screws (Fig. 3) to fasten the enclosure base to the
wall. 3. Drill the hole for cables in the enclosure base (Fig. 4).
2
SPP-110
SATEL
4. Place the enclosure base against the wall and mark the location of
mounting holes.
5. Drill the holes for wall plugs (screw anchors) in the wall.
6. Run the cables inside the enclosure base.
7. Use wall plugs and screws to secure the enclosure base to the wall. Select
wall plugs specifically intended for the mounting surface (different for
concrete or brick wall, different for plaster wall, etc.).
8. Use the DIP switches to configure the sounder settings (see: “Configuring
the sounder settings” p. 3).
9. Connect the zone circuit wires to the sounder (Fig. 5). If the sounder is
connected to the zone circuit at the end of line, screw a 10 k resistor to its
terminals. You can connect the cable shields to the E terminals (using a
shielded cable is not required).
SATEL
SPP-110
3
10. Replace the cover and turn it clockwise (Fig. 6). 11. Lock the cover with a screw (Fig. 7).
2.1 Configuring the sounder settings
Use the DIP switches on the electronics board (Fig. 8) to configure the
sounder settings.
2.1.1 Selecting the tone
To select the tone, use the switches 1-5, marked as S1-S5 on the electronics
board. The tones and their corresponding switch settings are described in
Table 1 (where: switch in ON position = 1; switch in OFF position = 0).
N DIP switch
o
12345
1 00000
2 10000
3 01000
4 11000
Acoustic signaling
Frequency Hz
Description
800 & 970
2 Hz (250 ms 250 ms)
800-970
7 Hz (7/s)
800-970
1 Hz (1/s)
2850
Continuous
4
N DIP switch
o
12345
5 00100
6 10100
7 01100
8 11100
9 00010
10 10010
11 01010
12 11010
13 00110
14 10110
15 01110
16 11110
17 00001
18 10001
19 01001
20 11001
21 00101
22 10101
23 01101
24 11101
25 00011
26 10011
27 01011
28 11011
29 00111
30 10111
31 01111
32 11111
Tone / supply voltage
1 / 18 VDC 1 / 28 VDC 2 / 18 VDC 2 / 28 VDC 3 / 18 VDC 3 / 28 VDC 4 / 18 VDC 4
/ 28 VDC 5 / 18 VDC 5 / 28 VDC 6 / 18 VDC 6 / 28 VDC 7 / 18 VDC
SPP-110
SATEL
Acoustic signaling
Frequency Hz
Description
2400-2850
7 Hz
2400-2850
1 Hz
500-1200
3 s sound, 0.5 s silence, repeated
1200-500
1 Hz
2400-2850
2 Hz (250 ms 250 ms)
970
0.5 Hz (1 s)
800 & 970
1 Hz (500 ms 500 ms)
2850
0.5 Hz (1 s)
970
0.8 Hz (250 ms / 1 s)
970
Continuous
554 & 440
100 ms 400 ms
660
3.3 Hz (150 ms)
660
0.28 Hz (1.8 s)
660
0.05 Hz (13 s / 6.5 Hz)
660
Continuous
554 & 440
0.5 Hz (1 s)
660
1 Hz (500 ms 500 ms)
2850
4 Hz (150 ms 100 ms)
800-970
50 Hz
2400-2850
50 Hz
970
3 x 500 ms sound, 1.5 s silence, repeated
800-970
3 x 500 ms sound, 1.5 s silence, repeated
970 & 800
3 x 500 ms sound, 1.5 s silence, repeated
2400
Continuous
990 & 650
2 Hz (250 ms 250 ms) (Symphoni Tones)
510 & 610
2 Hz (250 ms 250 ms) (Squashni Micro Tones)
300-1200
1 Hz
510 & 610
1 Hz (500 ms 500 ms)
Table 1.
Angle-dependent [°] minimum sound level [dBA]
15°
45°
75°
105°
135°
165°
74.3
85.7
89.9
89.4
84.2
77.0
77.0
87.2
91.4
90.9
85.8
80.0
78.0
85.7
89.1
88.8
83.5
78.0
79.6
87.5
90.7
90.4
85.4
79.9
78.9
86.1
90.0
89.7
83.9
78.2
80.9
87.8
91.3
91.0
85.8
80.3
71.0
81.0
83.5
82.0
79.7
69.6
71.3
81.4
84.04
82.6
79.7
69.7
75.3
83.4
85.6
85.0
81.1
75.0
75.2
83.4
85.5
85.0
81.0
74.5
76.6
84.7
86.7
86.4
82.6
75.1
76.4
84.6
86.4
86.1
82.6
75.1
79.8
87.2
91.8
91.5
85.8
81.5
SATEL
Tone / supply voltage
7 / 28 VDC 8 / 18 VDC 8 / 28 VDC 9 / 18 VDC 9 / 28 VDC 10 / 18 VDC 10 / 28 VDC
11 / 18 VDC 11 / 28 VDC 12 / 18 VDC 12 / 28 VDC 13 / 18 VDC 13 / 28 VDC 14 /
18 VDC 14 / 28 VDC 15 / 18 VDC 15 / 28 VDC 16 / 18 VDC 16 / 28 VDC 17 / 18 VDC
17 / 28 VDC 18 / 18 VDC 18 / 28 VDC 19 / 18 VDC 19 / 28 VDC 20 / 18 VDC 20 /
28 VDC 21 / 18 VDC 21 / 28 VDC 22 / 18 VDC 22 / 28 VDC 23 / 18 VDC 23 / 28 VDC
24 / 18 VDC 24 / 28 VDC 25 / 18 VDC 25 / 28 VDC 26 / 18 VDC 26 / 28 VDC 27 /
18 VDC 27 / 28 VDC 28 / 18 VDC 28 / 28 VDC 29 / 18 VDC 29 / 28 VDC
SPP-110
5
Angle-dependent [°] minimum sound level [dBA]
15°
45°
75°
105°
135°
165°
80.9
88.6
92.8
92.6
87.3
82.9
78.6
86.5
90.5
90.3
84.6
80.7
80.2
88.3
92.1
91.8
86.5
82.6
77.0
81.0
86.9
86.1
80.2
75.8
77.0
81.3
87.0
86.2
80.1
75.7
73.2
86.3
90.6
90.3
84.9
76.6
74.2
87.2
91.6
91.3
85.9
77.6
74.6
86.5
90.7
90.3
85.0
77.2
77.3
87.8
91.9
91.5
86.5
80.2
73.4
84.1
86.9
88.4
85.9
73.8
77.5
87.8
90.5
91.9
89.4
76.6
72.7
85.7
90.0
89.7
84.1
75.9
73.9
86.7
91.1
90.9
85.3
77.2
73.1
86.2
90.5
90.2
84.8
76.5
73.4
86.2
90.8
90.3
84.8
76.5
75.9
83.6
86.9
86.4
80.1
77.6
77.5
84.8
88.4
87.9
81.0
79.3
75.9
84.9
87.4
87.0
81.7
74.8
77.4
86.3
89.0
88.6
83.0
76.3
76.8
86.0
88.5
88.2
83.0
75.8
78.6
87.4
90.2
89.7
84.3
77.4
77.2
86.1
88.6
88.2
82.9
76.0
78.7
87.4
90.3
89.9
84.3
77.5
77.0
85.9
88.4
88.2
83.0
75.8
78.7
87.4
90.2
89.8
84.3
77.4
76.0
84.1
87.4
87.0
80.2
77.9
77.5
85.4
88.6
88.3
81.5
79.5
76.9
85.9
88.4
88.1
82.7
75.7
78.5
87.3
90.0
89.5
84.1
77.2
74.0
84.0
86.0
85.6
82.8
73.0
74.8
84.6
86.5
85.6
83.4
73.5
77.4
85.4
88.5
88.0
83.1
77.5
79.4
87.3
90.4
90.0
85.0
79.5
75.6
83.3
85.4
84.9
80.6
74.4
75.4
83.4
85.6
84.7
80.3
74.4
73.3
86.5
90.8
90.5
85.1
76.6
74.6
87.6
91.9
91.5
86.1
77.6
78.0
85.8
89.7
89.3
83.4
77.6
80.0
87.1
91.2
90.7
84.8
79.2
74.7
86.0
90.3
90.0
84.4
77.3
77.4
87.5
91.5
91.3
86.1
80.0
75.4
79.6
85.6
87.0
80.9
76.3
75.5
79.7
85.8
87.1
80.9
76.3
78.9
88.2
91.1
90.7
85.2
77.6
79.9
89.2
91.9
91.7
86.0
78.4
6
SPP-110
SATEL
Tone / supply voltage
30 / 18 VDC 30 / 28 VDC 31 / 18 VDC 31 / 28 VDC 32 / 18 VDC 32 / 28 VDC
Angle-dependent [°] minimum sound level [dBA]
15°
45°
75°
105°
135°
165°
76.4
84.9
87.6
87.3
81.8
76.1
77.9
86.3
89.0
88.8
83.1
77.7
77.8
86.0
89.8
89.5
83.9
79.4
78.4
86.6
90.4
90.1
84.6
80.1
76.4
85.1
87.6
87.4
81.9
76.2
77.9
86.5
89.2
89.0
83.0
77.8
Table 2.
2.1.2 Volume setting
Use the switch 6 (marked as V on the electronics board) to change the volume
of the following tones: 4, 5, 6, 9, 12, 14, 22 and 28. The switch in ON
position maximum volume (recommended). The switch in OFF position lower
volume. For other tones, it is recommended to set the switch to OFF position.
3. Maintenance
The fire alarm system elements require regular maintenance. The periodic
checks of the SPP-110 sounder should be carried out at least every 6 months.
In spaces where working conditions are difficult (e.g. dust, aggressive
environment that may cause corrosion, etc.), the periodic checks should be
carried out more often. As part of maintenance, start a test in the control
panel and make sure the acoustic signaling is working. Please go to the fire
alarm control panel manuals to find out how to start the test.
4. Specifications
Supply voltage …………………………………………………………………………………………. 18…28 VDC Alarm current
consumption ………………………………………………………………………………….15 mA Operating temperature
range…………………………………………………………………….-10°C…+55°C Maximum humidity
………………………………………………………………………………………………..95% Protection rating
………………………………………………………………………………………………… IP21C Operating environment
type………………………………………………………………………………………. A
SATEL
SPP-110
7
Dimensions ……………………………………………………………………………………..108 x 108 x 87 mm Weight………………………………………………………………………………………………………………. 225 g
8
SPP-110
SATEL
The SPP-110 fire alarm sounder conforms to the essential requirements of the
EU Regulations and Directives:
CPR 305/2011 Regulation of the European Parliament and of the Council of 9
March 2011 laying down harmonized conditions for the marketing of construction
products and repealing the Council Directive 89/106/EEC on construction
products;
EMC 2014/30/UE Electromagnetic Compatibility Directive;
LVD 2014/35/EU Low Voltage Directive.
The CNBOP-PIB Certification Body in Józefów issued the Certificate of
Constancy of Performance 1438-CPR-0880 for the construction product SPP-110
fire alarm sounder, confirming its compliance with the requirements of EN
54-3:2003+A1:2002+A2:2006.
The Certificate and the Declaration of Performance can be downloaded from the
www.satel.pl website.
The SPP-110 fire alarm sounder has been granted the Certificate of Admittance
No 4833/2023 by the CNBOP-PIB in Józefów. The Certificate of Admittance can be
downloaded from the www.satel.pl website.
23
SATEL Sp. z o.o. · ul. Budowlanych 66 · 80-298 Gdask · POLAND 1438
1438-CPR-0880 DOP/CPR/0880 EN 54 3:2003+A1:2002+A2:2006
Fire safety. SPP-110 fire alarm sounder (type A).
Declaration of Performance DOP/CPR/0880 Application fire safety. Technical
specifications please refer to this manual.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>