BOB AND BRAD QL/DMS.T2-C Massage Gun User Manual
- September 28, 2024
- Bob AND Brad
Table of Contents
BOB AND BRAD QL/DMS.T2-C Massage Gun
Maintenance
- The battery in this device is not designed to be removed or exchanged by the user. If there is any problem with the power supply, please contact us immediately.
- DO NOT attempt to open or repair the device by taking it apart yourself. Tampering with the mechanics of the device in any way will result in an automatic voiding of the product’s warranty.
Warnings and Safety Precautions
- Before connecting the device to the power supply, please ensure that the supply voltage stated on the rating plate is compatible with the unit.
- Please charge the new batteries fully before the first use.
- DO NOT submerge the device in water or any other liquid.
- DO NOT use the device for more than 30 minutes at a time. Wait 5 minutes prior to using the device again, following a 30-minute session with the device.
- DO NOT apply directly or around your head or genitals.
- DO NOT use the device to supplement or replace any medical treatment. Please consult your physician before using the device if you are experiencing unexplained pain, receiving medical treatment, or using medical equipment.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
FCC Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause any harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Plug the equipment into the outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help with the supplied fastener. DO NOT hang the unit by the power cord.
Disclaimer
Please contact your physician before using the Bob and Brad QL/DMS.T2-C Massage Gun if you have any physical health concerns or have any of the following conditions: pregnancy, diabetes, epilepsy, migraines, herniated disks, spondylolisthesis, recent joint replacements or IUDs. Please also contact your physician before use if you have undergone recent surgery or have any metal pins or plates in your body.
Main Structure and Fittings
- Fork Head Longer muscles such as calves, forearms, biceps, and ankle / Achilles area.
- Bullet Head Trigger points are found in the glutes, hips, traps, shoulders, and other complex muscle groups.
- Ball Head Sore muscles and a great starter attachment for larger muscle groups.
- Air Cushion Head Sensitive areas such as wrists, ankles, knees, traps, and around the neck.
- Flat Head Larger surface areas such as quads, hamstrings, back, and chest.
Operation Steps
- Connect the massage head to the device when the device is powered off. Insert the massage head completely with pressure and ensure the head is correctly positioned and the buckle is inserted into the slot. (Note: The Fork Head should be positioned for installation. When the buckle is inserted into the slot, the installation is in place. If the massage head is not installed in place, there will be a risk of falling out while in use.) To remove a massage head, simply turn off the device and pull out the interchangeable massage head.
- In the shutdown state, long press the “ ” button on the panel for 2 seconds to turn on and start the first speed. Promptly press the “ ” button on the panel to switch speeds between levels 0-5. When the device is running in levels 1-5, press the “ ” button and return to the level 0 position for 2 seconds to stop the output. Long press the ” ” button for 2 seconds while the device is in level 0 to shut down the device.
- After 10 minutes of operation, the device automatically turns off.
- LED lights indicate the corresponding strike frequency level from lowest (level 1) to highest (level 5).
- When the device is on standby (level 0), it will automatically shut down after 20 seconds of inactivity.
- Apply the required pressure at each preset vibration frequency to massage target muscle groups.
Battery display
- When the first indicator light (LED1) is on: 25% of the battery remains.
- When the second indicator light (LED2) is on: 50% of the battery remains.
- When the third indicator light (LED3) is on: 75% of the battery remains.
- When the fourth indicator light (LED4) is on: 100% of the battery remains.
Note :
- When the first indicator light (LED1) flashes, the battery power is below 10% and requires recharging.
- It is not recommended that the battery power be depleted below 25%.
About Charging
- Before the first use, please fully charge the device using the USB-A to
- USB-C Cable that came with the massage gun. A full charge takes about 4.5 hours. The device will not take charge using a USB-C to USB-C Cable.
- Connect the output end of the connection line to the DC charging port at the bottom of the device. Then connect the input end of the connection line to the mobile power source or mobile adapter for outlets (5V/2A; if the charging current or voltage is less than 5V/2A, charging time will be longer. Any regular phone adapter will be able to charge the massage gun without a problem).
- The battery icon on the handle flickers regularly. The digital display on the handle shows the battery power and indicates when the battery is being charged and the level of power remaining.
- When the battery icon on the handle stops flickering and remains on, the digital display shows that 100% of the battery is full.
- The battery can be recharged at any level of battery power. When charging, please ensure that the device is shut down. When the device is in operation, the charging will be automatically protected.
- The average working time with a full charge is about 2~5 hours. However, this varies depending on vibration frequency and massage pressure during use.
How to Fix Your Massage Gun if it Stops Working
- Recharge fully using the USB-A to USB-C Cable for 3-4 hours. It will not take charge if you are using USB-C to USB-C cable. The battery lights should be flickering when taking charge.
- Press and hold the power button for 3-5 seconds.
Technical Details
- Product Name: Massage Gun
- Product Model: QL/DMS.T2-C
- Speed: 2000-3200 r/min
- Rated Power: 25W
- Dimensions: 5.4″x2.4″x7.6″
- Rated Voltage: 7.3V
- Battery Capacity: 4000mAh
- Charging Time: 270 minutes
Guarantee
This product comes with a one-year warranty from the date of purchase. Warranty will be voided due to any of the following:
- Damaged due to improper usage or storage.
- Damaged by attempting to repair or disassemble the device.
- Period of warranty exceeded.
Utilize the Bob and Brad massage gun before, during, or after your workout for maximum benefits. This massage gun can help accelerate muscle tissue responsiveness by increasing hydration, range of motion, and function to tight muscles.
Indication| Action| Speed| Pressure| Indication|
Duration| Muscle Position| Movement
---|---|---|---|---|---|---|---
Warm Up / Activation
| Activate and prime muscles prior to exercise.
Reduce risk of injury.
|
Level 3
|
Light to Moderate
|
Warm UP
/Activation
|
30 sec or less
|
Relaxed. Move along the muscle.
|
Quick, high speed over area.
| | | Heavy| | | |
Mid Workout / Myofascial Mobility| Help muscle recovery and reactivation.|
Level 4
| (especially for large muscle
groups)
|
Mid Workout / Myofascial Mobility
|
8-12 sec
| Target specific area.|
Localised
Recovery
| Relax muscles and aid recovery.
Down-regulate or turn off muscles.
|
Level 1
or 2
|
Moderate to Heavy
|
Recovery
|
90 sec or more
|
Move along the muscle.
| Slow movement along the muscle
Pain Modulation
| Reduction in pain to
increase movement.
|
Level 1
|
Light
| Pain Modulation| 10 to 30
sec
| Relaxed.
Localised spot.
| Over painful
area.
Body Awareness
|
Improve movement or mechanics of a joint. Activation of a muscle. Draw attention to a muscle
|
All Levels
|
Light to Moderate
|
Body
|
10 to 20 sec
|
Relaxed or with movement
|
Over specific target area or movement over area.
CHEST
2 Minutes
- ATTACHMENT: BALL HEAD
- PROTOCOL: Sweep from A to B on each sice for 1 minute
- DURATION: 2 minutes
ABS
2 Minutes
- ATTACHMENT: BALL HEAD
- PROTOCOL: Sweep from A to B on each sice for 1 minute
- DURATION: 2 minutes
UPPER TRAPS
1 Minute
- ATTACHMENT: BALL HEAD
- PROTOCOL: Sweep from A to B on each side for 30 seconds
- DURATION: 1 minute
UPPER BACK
4 Minutes
ATTACHMENT: BALL HEAD
STEP 1 : Upper back
- PROTOCOL: Sweep from A to B on each side for 1 minute
- DURATION: 2 minutes
STEP 2 : Lower back
- PROTOCOL: Sweep from A to B on each side for 1 minute
- DURATION: 2 minutes
SHOULDERS
2 Minutes
- ATTACHMENT: BALL HEAD
- PROTOCOL: Sweep from A to B on each side for 1 minute
- DURATION: 2 minutes
BICEPS
2 Minute
- ATTACHMENT: BALL HEAD
- PROTOCOL: Sweep from A to B on each side for 1 minute
- DURATION: 2 minutes
TRICEPS
4 Minutes
- ATTACHMENT: BALL HEAD
- PROTOCOL: Sweep from A to B on each side for 2 minutes
- DURATION: 4 minutes
FOREARM
2 Minutes
- ATTACHMENT: BALL HEAD
- PROTOCOL: Sweep from A to B on each sice for 1 minute
- DURATION: 2 minutes
HANDS
1 Minute
- ATTACHMENT: BALL HEAD
- PROTOCOL: Sweep from A to B on each side for 30 seconds
- DURATION: 1 minutes
HIP FLEXORS
2 Minutes
- ATTACHMENT: BALL HEAD
- PROTOCOL: Sweep from A to B on each sice for 1 minute
- DURATION: 2 minutes
SHINS
1 Minute
- ATTACHMENT: BALL HEAD
- PROTOCOL: Sweep from A to B on each sice for 30 seconds
- DURATION: 1 minute
GLUTES
4 Minutes
- ATTACHMENT: FLAT HEAD
- PROTOCOL: Sweep from A to B on each side for 2 minutes
- DURATION: 4 minutes
HAMSTRINGS
2 Minutes
- ATTACHMENT: BALL HEAD
- PROTOCOL: Sweep from A to B on each sice for 1 minute
- DURATION: 2 minutes
CALVES
2 Minutes
- ATTACHMENT: BALL HEAD
- PROTOCOL: Sweep from A to B on each sice for 1 minute
- DURATION: 2 minutes
FEET
4 Minutes
- ATTACHMENT: BALL HEAD
- PROTOCOL: Sweep from A to B on each sice for 2 minutes
- DURATION: 4 minutes
A Dedicated Team Just For You
Every Bob and Brad product is backed by a 1-year warranty and an award-winning customer service team. If you are in any way dissatisfied with a product you ordered, we’ll exchange it, replace it or refund your money under the warranty. Simply email us the problem, and we’ll take care of it.
-
Troubleshoot
Help you solve any issues with your device. -
Initiate Returns
Provide instructions for replacements, returns and refunds. -
Product Knowledge
Answer questions about your device and best practices. -
Place New Orders
Help with placing orders online and/or authorized resellers.
Get in Touch.
- Call: +1 612-567-3035 Mon-Fri 9:00AM-4:30PM (CST)
- Email: support@bobandbrad.com
FLIGE Products LLC 3001 Esperanza Crossing Austin, TX 78758
FREQUENTLY ASKED QUESTIONS
What is the brand and model of this massage gun?
The brand is BOB AND BRAD, and the model is QL/DMS.T2-C.
What is the price of the BOB AND BRAD QL/DMS.T2-C Massage Gun?
The BOB AND BRAD QL/DMS.T2-C Massage Gun is priced at $119.99.
What are the product dimensions of the BOB AND BRAD QL/DMS.T2-C Massage Gun?
The dimensions of the BOB AND BRAD QL/DMS.T2-C Massage Gun are 7.6 x 2.4 x 5.4 inches.
How much does the BOB AND BRAD QL/DMS.T2-C Massage Gun weigh?
The item weight of the BOB AND BRAD QL/DMS.T2-C Massage Gun is 3.4 pounds.
What type of power source does the BOB AND BRAD QL/DMS.T2-C Massage Gun use?
The BOB AND BRAD QL/DMS.T2-C operates on a rechargeable lithium battery.
What is the battery capacity of the BOB AND BRAD QL/DMS.T2-C Massage Gun?
The battery capacity is 4000 mAh.
How long does it take to charge the BOB AND BRAD QL/DMS.T2-C Massage Gun?
It takes approximately 2-3 hours to fully charge the BOB AND BRAD QL/DMS.T2-C Massage Gun.
What is the usage time for the BOB AND BRAD QL/DMS.T2-C Massage Gun?
The usage time ranges from 2 to 5 hours, depending on the settings used.
What is the motor power of the BOB AND BRAD QL/DMS.T2-C Massage Gun?
The motor power is 25W with a brushless design.
How many speed levels does the BOB AND BRAD QL/DMS.T2-C Massage Gun have?
The BOB AND BRAD QL/DMS.T2-C features 5 speed levels, ranging from 2000 to 3200 RPM.
What is the amplitude of the BOB AND BRAD QL/DMS.T2-C Massage Gun?
The amplitude is 10 mm.
What is the noise level of the BOB AND BRAD QL/DMS.T2-C Massage Gun?
The noise level is approximately 45-50 dB.
How many massage heads are included with the BOB AND BRAD QL/DMS.T2-C Massage Gun?
The BOB AND BRAD QL/DMS.T2-C comes with 5 different massage heads.
Does the BOB AND BRAD QL/DMS.T2-C Massage Gun have an auto shut-off feature?
BOB AND BRAD QL/DMS.T2-C features an auto shut-off after 10 minutes of use.
What type of batteries does the BOB AND BRAD QL/DMS.T2-C Massage Gun require?
The BOB AND BRAD QL/DMS.T2-C requires 1 lithium metal battery.
DOWNLOAD THE PDF LINK:BOB AND BRAD QL-DMS-T2-C Massage Gun User Manual
REFERENCE:BOB AND BRAD QL/DMS.T2-C Massage Gun User Manual- Device.Report
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>