CASA FIXTURES CFF-502 2 in 1 Pull Out Kitchen Filtration Faucet Installation Guide

CFF-502 2 in 1 Pull Out Kitchen Filtration Faucet

“`html

Product Information

Specifications

• Dimensions:
  • Height: 10-9/16″ (268 mm)
  • Width: 6-3/8″ (163 mm)
  • Depth: 14″ (355 mm)
  • Spout Height: 12-5/8″ (321 mm) Max-1-3/4″ (Max-45mm)
  • Spout Reach: 7-1/2″ (190 mm)
  • Weight: 8.11 lbs (3.68 kg)
• Filtration System: Yes

Product Usage Instructions

Installation

1. Shut off water suppliers and remove the old faucet. Clean the
   mounting surface.

2. Flush the pipes by opening the angle valve for 60 seconds if
   it’s a first-time installation.

3. Insert the pull-out hose into the connector and tighten using a
   hex wrench. Test if securely locked.

4. Put the rubber O-ring into the bottom gap of the faucet and
   insert it into the faucet hole.

5. Slide rubber washer, metal washer, and mounting bracket onto
   the thread shank from underneath the countertop.

6. Adjust the position of the faucet body if necessary and tighten
   the mounting nuts with a Phillips screwdriver.

7. Screw the flexible hoses into the mixer body from underneath
   the counter and hand-tighten fully.

8. Connect and tighten the supply hoses using two adjustable
   wrenches, avoiding twisting or kinking.

9. If using 1/4 tubing, directly connect it to the pre-installed
   1/4 quick connector. For 3/8 tubing, follow step 9B.

Cleaning and Care

Clean the faucet often with a soft cloth. For heavy cleaning,
use mild liquid detergents or non-abrasive polisher. Avoid abrasive
cleaners and harsh chemicals to maintain the finish and
warranty.

Tools Needed

• Plumbers Tape
• Safety Glasses
• Phillips Screwdriver
• Wrench
• Silicone Sealant

FAQ

Q: Can I install the product myself without professional

help?

A: While it’s recommended to have a licensed plumber install the
unit for best results, you can follow the detailed installation
instructions provided.

Q: What should I do if I encounter missing parts during

installation?

A: Contact our customer service team at CASA FIXTURE VOLUME-C at
833-888-8223 for assistance with any missing parts or assembly
questions.

“`

Installation Guide
Halo CFF-502

Before Installation
CAUTION
Failure to read these instructions prior to installation may result in personal injury, property damage, or product failure. Manufacturer assumes no responsibility for product failure due to improper installation.
DO NOT RETURN TO STORE
If you have any trouble, contact us before reaching out to the retailer. we’ll make it right. Our customer service team will be glad to assist you with any assembly, missing part or questions that you may have about your products.
Contact CASA FIXTURE VOLUME-C 833-888-8223
PRIOR TO INSTALLATION
1- For best results, we recommends that this unit be installed by a licensed, professional plumber. 2- Please read over these instructions thoroughly before beginning installation. Make sure that you have all
tools and supplies needed to complete the installation. 3- Please flush the water system to ensure that no metal swarf, solder, and other impurities can enter the
faucet that might damage the cartirdge. (Most of the leakages and water flow issues are from avoilding this very necessary step). 4- Turn off the hot and cold water lines at the angle valve and turn on the old faucet to release any built-up pressure. 5- Keep this booklet and the receipt (or other proof of date and place of purchase) for this product in a safe place. The receipt is required should it be necessary to request warranty parts. 6- Please keep the box and packaging materials until your product is completely installed and functional.
Cleaning and Care
Clean the faucet often with a soft cloth to keep it looking like new. For heavy cleaning you can use mild liquid detergents or non-abrasive liquid polisher. Rinse with water and dry with a soft cloth. Avoid abrasive cleaners, steel wool and harsh chemicals as these will dull the finish and void your warranty.
Tools you may need

Plumbers Tape

Safety Glasses

Phillips Screwdriver

Wrench

Silicone sealant

Dimensions
Critical dimensions show in mm
10-9/16 ” (268 mm)

6-3/8 ” (163 mm)

14 ” (355 mm) 12-5/8 ” (321 mm) Max-1-3/4″ (Max-45mm)

7-1/2 ” (190 mm)
8-11/16 ” (220 mm)

1-5/16 ” (34 mm)

2-3/16 ” (55 mm)

Filtration-System

Parts List

Spout
This facing outward
Drink Water Cartridge Assembly
Friction Ring Drink Water
Handle Screw M5x6
Mounting Part

Sprayer Retainer

Hose Assembly

Magnet Bonnet Nut

013351000 Drink Water Aerator
Mixed Handle Assembly

Cover CT35TF061 Mixed Cartridge Gasket
Quick Connect 1/4″ to M11 2 in 1 Connector
Check Valve

Internal Hex Screw M5x3
Water Line M10_3/8″_27-1/2″
Service Key for Drink water Aerator
Quick Connect 3/8″ to M11 Allen Key 2.5mm
Weight Balance

Sprayer Head
443030000 Mixed Aerator

Faucet Installation
1

2
1 2

Shut off water suppliers. Remove the old faucet, clean the mounting surface. Note: For first time install, flush the pipes first by open the angel valve to run 60s.

Remove the mounting hardware from the mounting pipe.

3

4

Insert the pull-out hose into the connector and tighten it using a hex wrench from the side of the connector. Then, pull the hose gently to test if it is securely locked in place.

Put the rubber O-ring into the bottom gap of faucets then Insert faucet into faucet hole.

5

6

From underneath the countertop, Slide rubber washer, metal washer and mounting bracket onto the thread shank.

Adjust position of faucet body if necessary, Then tighten the mounting nuts with phillips screwdriver until snug.

Faucet Installation

7

8

From the under-side of counter, screw the flexible hoses into the mixer body and fully hand tighten.

Connect and tighten the supply hoses by using two adjustable wrenches (avoid twisting or kinking).

9A

9B

1/4″ (6.35mm)
Filtration-System
For 1/4″ Tubing: We have already pre-installed a 1/4″ quick connector. Please directly connect the 1/4″ tubing from your water filtration system to this connector. Please follow step 9B if you are using 3/8″ tubing.

1
2
3/8″ (9.53mm)
Filtration-System
For 3/8″ Tubing: From the underside of the counter, replace the 1/4″ quick connector on the faucet with the 3/8″ quick connector from the spare parts kit, and then use your 3/8″ tubing to connect to the 3/8″ quick connector. Please follow step 9A if you are using 1/4″ tubing.

10

11

Install the hose weight on the outlet side of the hose, near the loop.

Turn on the water suppliers, Shut off the faucet and check for leaks.

Trouble-Shooting

If you’ve followed the instructions carefully and your faucet still does not work properly, take these corrective steps.

Problem

Cause

Action

Low flow

Aerator or Filter may be clogged

Unscrew aerator to check rubber packing or replace aerator. (Note: some models require wrench to remove aerator.)

Faucet leaks from under Bonnet nut has come loose or

handle

cartridge needs to be reseated

Remove handle and cap. Using a wrench, ensure bonnet nut is tight.

If leak persists, faucet leaks from spout outlet, water does not shut off completely

Cartridge may need to be adjusted or replaced

SHUT OFF WATER SUPPLIES. Replace cartridge. When reinstalling parts, make sure bonnet nut is tightened securely with a wrench. WARNING: Failure to securely tighten bonnet nut with a wrench could result in water damage.

Leaking between spray head and the hose

Spray head may be loose or washer is not seated correctly in the hose connection

Tighten spray head by hand until snug. Make sure washer is seated correctly

Hose does not retract Weight may be installed incorrectly Readjust weight on hose

LIMITED LIFETIME WARRANTY
Thank you for choosing our faucets and accessories. We are dedicated to providing you with exceptional products that are built to last. CASA FIXTURES is proud to offer a comprehensive limited lifetime warranty on our kitchen and bathroom faucets and accessories. Here are the details of our warranty policy:
CASA FIXTURES warrants the structure and finish of the faucets and accessories to be free from defects in material and workmanship under normal usage for as long as the original purchaser resides in the residence in which the product was first installed. Additionally, the following warranty periods apply to specific components:
· Sprayhead Assembly: CASA FIXTURES warrants the sprayhead assembly, including the engine, aerators, structure, restrictors, backflow preventers, sprayer hoses, and braided supply line hoses (nylon, silicon, and stainless steel), to be free from defects in material and workmanship under normal usage for a period of one (1) year from the date of purchase.
· Cartridge: CASA FIXTURES warrants the faucet’s cartridge to be free from defects in material and workmanship under normal usage for a period of five (5) years from the date of purchase.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>