CASA FIXTURES CBA-16 Fusion 4-Piece Bathroom Hardware Set Installation Guide

July 24, 2024
CASA FIXTURES

CASA FIXTURES CBA-16 Fusion 4-Piece Bathroom Hardware Set

CASA-FIXTURES-CBA-16-Fusion-4-Piece-Bathroom-HardwareSet-
PRODCUT

Specifications

  • Series: Fusion CBA-16**
  • Warranty: 1 year from date of purchase

Product Usage Instructions

Safety Tips
Do not use the product as a grab bar. Avoid mounting in locations where it might be used as a grab bar. Exercise caution when drilling into walls to prevent damage to electrical and plumbing lines.

Cleaning Instructions
Use a soft, damp cloth to clean the product. Avoid scrub pads, detergents, or cleansers as they may harm the finish. Damage from improper care is not covered by the warranty.

Tools Needed for Installation

  • Electric drill
  • Tape measure
  • Hammer
  • Phillips screwdriver
  • Pencil
  • Lever
  • 1/4 in. drill bit
  • Silicone sealant

Installation Steps for Two-Post Installation

  1. Drill 5/16″ holes.
  2. Use the provided pin to install drywall anchors.
  3. Secure the mounting plate.

Installation Steps for Single-Post Installation

  1. Loosen the set screw and remove the mounting plate from the accessory.
  2. Position the mounting base and verify plumb.
  3. Mark the positions of the screw holes.
  4. For drywall into studs: Drill 1/8″ holes, and secure the mounting plate.
  5. For drywall between studs: Drill 5/16″ holes, use the provided pin for drywall anchors, and secure the mounting plate.
  6. For ceramic tile: Drill 1/4″ holes, insert ceramic anchors, and secure the mounting plate.
  7. Slide the accessory onto the mounting plate and tighten the set screw.

Installation Considerations

  • These products should be located and mounted to a wall stud. While it is possible to mount them to any surface, a stud-mounted product will yield the best results.
  • Keep this booklet and the receipt (or other proof of date and place of purchase) for this product in a safe place. The receipt is required to request warranty parts.
  • Please keep the box and packaging materials until your product is completely installed.

SAFETY TIPS

WARNING!
This item is not designed for use as a grab bar. Do not mount in locations where the product is likely to be used as a grab bar.

WARNING!
Use caution when drilling into walls to avoid drilling into electrical and plumbing lines hidden within the wall.

Cleaning Instructions:

  • To maintain and protect the fine luster of all bath accessories, clean them with a soft, damp cloth only. DO NOT USE scrub pads, detergents or cleansers as they may harm the protective finish of your bath accessories.
  • Damage to the product caused by improper care or the use of improper cleaning agents is not covered by the warranty.

Warranty:
Warranted to be free from manufacturing defects for one (1) year from the date of purchase.

Tools you may need

CASA-FIXTURES-CBA-16-Fusion-4-Piece-Bathroom-HardwareSet-
FIUG-1

Dimensions

CASA-FIXTURES-CBA-16-Fusion-4-Piece-Bathroom-HardwareSet-
FIUG-2 CASA-FIXTURES-
CBA-16-Fusion-4-Piece-Bathroom-HardwareSet-FIUG-3

Single-Post Installation

  • Loosen the set screw and remove the mounting plate from the accessory.
  • Position the mounting base and verify plumb. Mark the positions of the screw holes.
  • Drill 1/8” holes. Secure the mounting plate.CASA-FIXTURES-CBA-16-Fusion-4-Piece-Bathroom-HardwareSet-FIUG-4
  • Drill 5/16” holes. Use the provided pin to install the drywall anchors. Secure the mounting plate.
  • Drill 1/4” holes. Insert ceramic anchors. Secure the mounting plate.
  • Slide the accessory onto the mounting plate. Tighten the setscrew.CASA-FIXTURES-CBA-16-Fusion-4-Piece-Bathroom-HardwareSet-FIUG-5

Two-Post Installation

  1. Loosen the set screw and remove the mounting plate from the accessory.
  2. Position the mounting plate and verify plumb. Mark the positions of the screw holes.
  3. Drill 1/8″ holes. Secure the mounting plate.CASA-FIXTURES-CBA-16-Fusion-4-Piece-Bathroom-HardwareSet-FIUG-6
  4. Drill 5/16″ holes. Use the provided pin to install the drywall anchors. Secure the mounting plate.
  5. Drill 1/4″ holes. Insert ceramic anchors. Secure the mounting plate.
  6. Slide the accessory onto the mounting plate. Tighten the setscrew.CASA-FIXTURES-CBA-16-Fusion-4-Piece-Bathroom-HardwareSet-FIUG-7

Frequently Asked Questions

  • Q: Can this product be used as a grab bar?
    • A: No, this product is not designed for use as a grab bar. Avoid mounting it in locations where it might be used as one.
  • Q: What cleaning agents should be avoided?
    • A: Avoid using scrub pads, detergents, or cleansers as they may harm the protective finish of the product.

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals