CASA FIXTURES CSF-4010 Halo 2 Function Thermostatic Wall Mount Shower System Installation Guide

CSF-4010 Halo 2 Function Thermostatic Wall Mount Shower System

“`html

Specifications

• Min. Dimensions: 78 in. (1981 mm)
• Max. Dimensions: 94 in. (2387 mm)
• Critical Dimensions: Refer to mm measurements provided

Product Usage Instructions

Before Installation

Prior to installation, it is recommended to have a licensed
plumber install the unit for best results. Ensure you have read the
instructions thoroughly and have all the necessary tools and
supplies ready. Flush the water system to remove any impurities
before installation.

Cleaning and Care

Clean the faucet regularly with a soft cloth. For heavy
cleaning, use mild liquid detergents or non-abrasive polisher.
Avoid abrasive cleaners and harsh chemicals to maintain the finish
and warranty.

Tools You May Need

• Drill
• Level
• Safety Glasses
• Phillips Screwdriver
• Wrench
• Silicone Sealant
• Pencil
• Plumbers Tape
• Tape Measure
• Angle Grinder

Installation Schematics

Follow the provided schematics for correct installation. Ensure
proper distances are maintained as per the dimensions
specified.

Parts List

• Escutcheon Shower Arm
• Shower Head Hand Shower
• Trim Plate

Valve Installation Instructions

1. Finished Wall: Shut off water supplies before
   installing the valve. Position the valve so the finished wall fits
   between the MIN and MAX marks on the mudguard.

2. Wall Mounting: Use a spirit level for
   reference, mark the position for fixing lugs, drill holes, and
   securely fix the valve to the wall.

3. Connect Water Supplies: Open water supplies,
   flush pipes, and then connect the valve body to water supplies
   using proper fittings. Cold (C) and hot (H) inlet ports should be
   connected accordingly.

FAQ

Q: Can I install the product myself without a professional

plumber?

A: While it is recommended to have a licensed plumber install
the unit for best results, if you have experience with plumbing
installations and follow the instructions carefully, you may
install it yourself.

Q: What should I do if I encounter missing parts during

installation?

A: In case of missing parts, please contact our customer service
team at CASA FIXTURE VOLUME-C at 833-888-8223 for assistance.

“`

Installation Guide
Halo CSF-4010

Before Installation
CAUTION
Failure to read these instructions prior to installation may result in personal injury, property damage, or product failure. Manufacturer assumes no responsibility for product failure due to improper installation.
DO NOT RETURN TO STORE
If you have any trouble, contact us before reaching out to the retailer. we’ll make it right. Our customer service team will be glad to assist you with any assembly, missing part or questions that you may have about your products.
Contact CASA FIXTURE VOLUME-C 833-888-8223
PRIOR TO INSTALLATION
1- For best results, we recommends that this unit be installed by a licensed, professional plumber. 2- Please read over these instructions thoroughly before beginning installation. Make sure that you have all
tools and supplies needed to complete the installation. 3- Please flush the water system to ensure that no metal swarf, solder, and other impurities can enter the
faucet that might damage the cartirdge. (Most of the leakages and water flow issues are from avoilding this very necessary step). 4- Turn off the hot and cold water lines at the angle valve and turn on the old faucet to release any built-up pressure. 5- Keep this booklet and the receipt (or other proof of date and place of purchase) for this product in a safe place. The receipt is required should it be necessary to request warranty parts. 6- Please keep the box and packaging materials until your product is completely installed and functional.
Cleaning and Care
Clean the faucet often with a soft cloth to keep it looking like new. For heavy cleaning you can use mild liquid detergents or non-abrasive liquid polisher. Rinse with water and dry with a soft cloth. Avoid abrasive cleaners, steel wool and harsh chemicals as these will dull the finish and void your warranty.
Tools you may need

Drill Level

Safety Glasses

Phillips Screwdriver

Wrench

Silicone sealant

Pencil

Plumbers Tape

Tape Measure

Angle Grinder

Installation Schematics
Min. 78″(1981mm) Max. 94″(2387mm)
Min. 45″(1143mm) Max. 48″(1219mm)
Installation Schematics ­ Measuring for Ideal Shower Performance. Position the valve body 45-48 inches from the floor of the tub basin. (Follow valve instruction for proper valve body installation). The shower arm should be placed 78-94 inches above the floor of the tub basin. (Follow shower arm instruction for proper threaded adapter installation).

Dimensions
Critical dimensions show in mm

3/4 in. FNPT
1-3/4″ (44 mm)

2-1/8″ (54.5 mm)

3-1/8″ (79.5 mm)
Cold

3/4 in. FNPT

3-7/8″ (100 mm)

Hot
4-3/4″ (120 mm)

3/4 in. FNPT

3-1/8″ – 3-7/8″ (80-97 mm) 2-3/4″ (69.5 mm)

8 1/4 ” (210 mm)
1/2 in. MNPT 1″ (25 mm)
1/4 ” (7 mm)

2 3/8 ” (60 mm)

15 3/4 ” (400 mm)

9 13/16 ” (250 mm)
15/16 ” (24 mm)

3 3/8 ” (85 mm)

3 3/8 ” (85 mm)

4 5/16 ” (110 mm)

3/4 in. FNPT

59″ (1500mm)
12 3/16 ” (309 mm)

3″ – 4″ (74-102 mm)

3 5/16 ” (84 mm)

Parts List
Escutcheon Shower Arm

Shower Head Hand Shower

Trim Plate

Decorative Sleeve Friction Ring

Themostatic Handle

Friction Ring

Trim Plate Decorative Sleeve

Set Screw M5x5

Serives Key for Valve

Trim Plate Quick Connect
Holder Set Screws M5x8

Set Screw M5x6

Mounting Screws for Shower Valve
Shower Hose

Plug

Check Valve

Thermostatic Cartridge

Spline Adapter

Diverter Bonnet Nut

Bonnet Nut Temperature Stop Ring

Tapeless Installation Adapter

Ring Retainer
Gear Cipher Adapter

Mudguards

Plug Mudguards

Mudguards

Valve Installation Instructions
1
Finished Wall

SHUT OFF WATER SUPPLIES. This valve is designed to fit into a wall that is 3″-4″(80 – 97mm) from the finished wall to the back of the valve. Turn off the water supplies, Install the valve so the finished wall will fit between the MIN and the MAX mark on the mud guard

3″ – 4″ 80-97

2

Using the spirit level for leveling reference, Position the valve onto the wall and mark the

position for the fixing lugs, drill the holes and

fixing the valve to the wall with the supplied

screws.

3
C
H

Open the water suppliers, flush the pipes then close the water supplied. Connect the valve body to water supplies using proper fittings, (C) is the cold inlet port and (H) is the hot inlet port, then connect the water outlet accordingly.

Valve Installation Instructions
4

Open the water suppliers and proceed the pressure and leakage tests.

5

Using the mud guard as temperate, cut the tile opening, then put on the tiles accordingly.

Once the valve has been secured to the wall, the

plastic dust cover can be temporarily attached

to the valve, This will protect the valve while

additional work is completed.

Trim Installation Instructions
1

Following the cutline on the box, cut the additional box part.

2

Remove the plug by using the supplied spanner.

3

Slide large decorative tube(1) onto the valve. Use water to wet the round rubber gaskets on

the trim plate(2) and slide trim plate over(2)

decorative tube. Gently press trim plate(2) against

the finished wall.

Thread the quick connector(3) through the trim

2

plate(4) and attach it to the valve body.

2

Please make sure you place in correct orientation

1 1

if there are etchings on the front of the cover plate.

4

3

Trim Installation Instructions
6

After adjusting water temperature, and ensuring temperature stop ring is in place, install temperature handle onto spindle so that the push button is at the top. Use Allen wrench to secure set screw and push in silicone plug.
Position diverter handle at the desired upward position, loosen screw and rotate spindle adapter and at the same time rotate diverter handle until the desired position is achieved. Secure the spindle adapter with screw and diverter handle with set screw by using Allen wrench Push in silicon plug.
Install the shower holder onto quick connector, then connect shower hose and hand shower accordingly.

Adjusting Water Temperature
G H
The thermostatic valve is preset at the factory and tested at 100 F (38 C) indicated by the red mark (#H) on the spindle aligning with the straight black line (#G) on the thermostatic cartridge body at the twelve o’clock position. To calibrate temperature according to your own operating conditions, follow the steps below: 1. Turn on the valve and check the temperature of water at any shower element with a thermometer. 2. Turn the spindle clockwise or counter-clockwise until temperature at the shower element reaches 100 °F (38 °C). 3. Ensure the temperature stop ring is fitted onto the thermostatic cartridge with the open slot pointing upward. 4. Install temperature handle (supplied in the trim package) so that the anti-scalding push button on the thermostatic cartridge is at the top.

Shower Head and Shower Arm Instructions

1

SHUT OFF WATER SUPPLIES. Consider the type and the thickness of your

finished wall before placing your stringer back

plate.

Finished wall

Install the threaded adapter (Not supplied) so

the surface of the finished wall is flush with the

front of the threaded adapter.

Flush with the finished wall

Make sure that 1/2″ threaded adapter is installed securely inside the wall.

2

Slide escutcheon over shower arm, and apply Teflon tape onto male threads.

3

Screw the shower arm into threaded adapter. Screw the shower head onto the shower arm and

tighten with an adjustable wrench.

Limited Lifetime Warranty
Thank you for choosing our faucets and accessories. We are dedicated to providing you with exceptional products that are built to last. CASA FIXTURES is proud to offer a comprehensive limited lifetime warranty on our kitchen and bathroom faucets and accessories. Here are the details of our warranty policy:
CASA FIXTURES warrants the structure and finish of the faucets and accessories to be free from defects in material and workmanship under normal usage for as long as the original purchaser resides in the residence in which the product was first installed. Additionally, the following warranty periods apply to specific components:
· Sprayhead Assembly: CASA FIXTURES warrants the sprayhead assembly, including the engine, aerators, structure, restrictors, backflow preventers, sprayer hoses, and braided supply line hoses (nylon, silicon, and stainless steel), to be free from defects in material and workmanship under normal usage for a period of one (1) year from the date of purchase.
· Cartridge: CASA FIXTURES warrants the faucet’s cartridge to be free from defects in material and workmanship under normal usage for a period of five (5) years from the date of purchase.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>