maono WM600 C2 Wireless Microphone System User Guide

: June 12, 2024
: maono

Table of Contents

maono WM600 C2 Wireless Microphone System
Product Information
Product Usage Instructions
FCC Statement
Measures
Key operation and LED lighting instructions
Technical Specification
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

maono WM600 C2 Wireless Microphone System

Product Information

Product Name: WM600 C2 Wireless Microphone system
Model Number: WM600 C2
Weight: 120g
Version: V1.1-20221012
Manufacturer: CET PRODUCT SERVICE LTD.
Manufacturer Address: Chase Business Centre, 39-41 Chase Side, London N14 5BP United Kingdom
Email: info.cetservice@gmail.com
Technical Support: support@maono.com
Website: www.maono.com
FCC ID: 2AJJBWM600

Product Usage Instructions

Transmitter (TX1 & TX2)
On/Off Button: Press and hold for three seconds to switch the machine. Short press to turn mute on and off. Double-click to turn noise reduction on or off.

RESET Button: Use a pin to press the reset button for 3 seconds.

USB C Charging Port: Use a DC 5V charger to connect to the USB C charging port.

LED Indicator: There is a light hole on the front, which is displayed by RGB monochrome lights (red, green, blue). After fully charged, the red indicator light will be off. Green light indicates connection is always on, search flashes slowly, clear pairing flashes quickly. The side indicator displays the mute state, with red light indicating muted and light off in normal use.

Receiver (RX)
RESET Button: Use a pin to press the reset button for 3 seconds.

USB-C Male Plug: Connect the receiver to a
USB-C port.

3.5mm Headphone Jack: Use the 3.5mm headphone jack for real-time transmitter sound monitoring and playing back the sound on the phone.

LED Indicator: The connection indicator is always on green when there is a normal connection. It flashes slowly when disconnected from the transmitter and flashes quickly when the pairing is cleared. When noise reduction is turned on, the blue light is always on.

Note: The information and data contained in this manual are subject to change without notice in advance.

maono-WM600-C2-Wireless-Microphone-System-1

maono-WM600-C2-Wireless-Microphone-System-2

maono-WM600-C2-Wireless-Microphone-System-3

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment oﬀ and on, the user is encouraged to try to correct the interference by one or more of the following.

Measures

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit diﬀerent from that to which the.
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Key operation and LED lighting instructions

Buttons (Transmitter TX1 & TX2)
On/Off button – Press and hold for three seconds to switch the machine;
Short press to turn mute on and off;
Double-click to turn noise reduction on or off.
RESET – use a pin to press the reset button for 3 seconds.

Connector (Transmitter TX1 & TX2)
USB C charging port – DC 5V.

LED Indicator (Transmitter TX1 & TX2)
There is a light hole on the front, which is displayed by RGB monochrome lights (red, green, blue);
After fully charged, the red indicator light will be off;
Green light: connection is always on, search flashes slowly, clear pairing flashes quickly.
The side indicator is used to display the mute state, and the red light is on when it is muted, and the light is off in normal use.

Buttons (Receiver RX)
RESET – use a pin to press the reset button for 3 seconds.

Connector (Receiver RX)
USB-C male plug.
3.5mm headphone jack for real-time transmitter sound monitoring and playing back the sound on the phone.

LED Indicator (Receiver RX)
Connection indicator:
Normal connection is always on green;
Disconnected from the transmitter, the green light flashes slowly; The green light flashes quickly when the pairing is cleared; When noise reduction is turned on, the blue light is always on.