CASA FIXTURES CSF-4004 Pressure Balanced 3 Function Wall Mount Shower System Installation Guide

CSF-4004 Pressure Balanced 3 Function Wall Mount Shower System

“`html

Specifications

• Dimensions: Various critical dimensions detailed in mm
• Parts List: Detailed list of components included

Product Usage Instructions

Before Installation

Make sure to read the installation guide thoroughly to prevent
personal injury or product failure. Contact customer service for
assistance.

Installation

1. It is recommended to have a licensed plumber install the
   unit.

2. Read the instructions carefully and gather all necessary tools
   and supplies.

3. Flush the water system before installation.

Cleaning and Care

Regularly clean the faucet with a soft cloth. For heavy
cleaning, mild liquid detergents can be used. Avoid abrasive
cleaners as they may damage the finish.

Tools Needed

• Plumbers Tape
• Safety Glasses
• Phillips Screwdriver
• Wrench
• Silicone Sealant

Installation Schematics

Detailed placement instructions for shower and tub components
are provided. Follow the specified measurements for proper
installation.

Frequently Asked Questions (FAQ)

Q: Can I install the Halo CSF-4004 unit myself?

A: It is recommended to have a licensed plumber install the unit
to ensure proper installation and to avoid any issues.

Q: What should I do if I encounter missing parts during

installation?

A: Contact customer service at CASA FIXTURE VOLUME-C for
assistance with any missing parts or assembly questions.

Q: How should I clean the faucet to maintain its

appearance?

A: Use a soft cloth for regular cleaning and mild liquid
detergents for heavier cleaning. Avoid abrasive cleaners that may
damage the finish.

“`

Installation Guide
Halo CSF-4004

Before Installation
CAUTION
Failure to read these instructions prior to installation may result in personal injury, property damage, or product failure. Manufacturer assumes no responsibility for product failure due to improper installation.
DO NOT RETURN TO STORE
If you have any trouble, contact us before reaching out to the retailer. we’ll make it right. Our customer service team will be glad to assist you with any assembly, missing part or questions that you may have about your products.
Contact CASA FIXTURE VOLUME-C 833-888-8223
PRIOR TO INSTALLATION
1- For best results, we recommends that this unit be installed by a licensed, professional plumber. 2- Please read over these instructions thoroughly before beginning installation. Make sure that you have all
tools and supplies needed to complete the installation. 3- Please flush the water system to ensure that no metal swarf, solder, and other impurities can enter the
faucet that might damage the cartirdge. (Most of the leakages and water flow issues are from avoilding this very necessary step). 4- Turn off the hot and cold water lines at the angle valve and turn on the old faucet to release any built-up pressure. 5- Keep this booklet and the receipt (or other proof of date and place of purchase) for this product in a safe place. The receipt is required should it be necessary to request warranty parts. 6- Please keep the box and packaging materials until your product is completely installed and functional.
Cleaning and Care
Clean the faucet often with a soft cloth to keep it looking like new. For heavy cleaning you can use mild liquid detergents or non-abrasive liquid polisher. Rinse with water and dry with a soft cloth. Avoid abrasive cleaners, steel wool and harsh chemicals as these will dull the finish and void your warranty.
Tools you may need

Plumbers Tape

Safety Glasses

Phillips Screwdriver

Wrench

Silicone sealant

Installation Schematics

Min. 78″(1981mm) Max. 94″(2387mm)
Min. 48″(1219mm) Max. 59″(1498mm)
Shower Only: Min. 45″(1143mm) Max. 48″(1219mm)
With Tub: Min. 32″(813mm) Max. 42″(1067mm)
Min. 23″(584mm) Max. 26″(661mm)

Installation Schematics ­ Measuring for Ideal Tub/Shower Performance Installation of this product at non-recommended measurements may lead to issues such as water discharge from the showerhead during tub fill mode.
Tub/Shower Position the valve body 32-42 inches from the floor of the tub basin. (Follow valve instruction for proper valve body installation).
Shower Only Position the valve body 45-48 inches from the floor of the tub basin. (Follow valve instruction for proper valve body installation).

The shower arm should be placed 78-94 inches above the floor of the tub basin. (Follow shower arm instruction for proper threaded adapter installation).
The hand shower should be placed 48-59 inches above the floor. (Follow hand shower holder instruction for proper threaded adapter installation).
The tub spout should be placed 23-26 inches above the floor. (Follow tub spout instruction for proper threaded adapter installation).

Dimensions
Critical dimensions show in mm
Five 1/2 in. MNPT

4 1/4″ (107 mm)

2 11/16 ” (68 mm) 1 3/4 ” (45 mm)

6 1/8″ (155 mm) 1 1/2 ” (38 mm)

2 13/16 ” (72 mm)
5 3/8 ” (136 mm)

5/8 ” (16 mm)

1 9/16 ” (40 mm)
3 1/16 ” (78 mm)
4 3/16 ” (106 mm)

1/2 MNPT

2 3/8″ (60 mm)

7 1/16″ (180 mm)

2 3/16″ (55 mm)

2 3/8″ (60 mm)

15 3/4″ (400 mm)

1 3/4″ – 3″ (45-75 mm)
1/2 MNPT

9 13/16″ (250 mm)

3 1/8″ (80 mm)
7 7/8″ (200 mm)

1/2 MNPT 1/2 FNPT

Parts List

Shower Head

Escutcheon

Shower Arm

Hand Shower

Trim Plate

Decorative Tub Assembly

Escutcheon

Decorative Tub

Gear Cipher Adapter
Diverter Handle

Cover

Handle

Quick Connect for Supply Elbow
Supply Elbow with HandShower Holder
Set Screws for Supply Elbow
Mounting Screws for Shower Valve

Shower Hose Escutcheon

Bath Spout

Diverter Cartridge Retaining Nut

Rough-in Box and Screws Mudguards

Check Valves

Pressure Balaning Cartridge

Retaining Nut

Valve Installation Instructions
1
Finished wall

SHUT OFF WATER SUPPLIES. Consider the type and thickness of your finished wall before placing your stringer back plate.

Flush with the finished wall

2

Install the body so the surface of the finished wall is flush with the front of the rough-in box. Make

sure the word “UP” are on top of the valve body

when installing.

3A
Hot

Connect the valve body to water supplies using

proper fittings (copper tubing, iron pipe or PEX).

Note: For PEX, be sure to use the right fitting

for crimping and the right tool for cold

expansion.

If any of the three outlet ports is to be unused,

seal the port with a pipe plug.

Note: Left is the hot inlet port and right is the

cold inlet port.

If you are making a back-to-back or reverse

installation (hot on the right and the cold on left)

install the valve body as described, but the water

supply lines will be reversed.

Note: Right is the hot inlet port and left is the

Cold

cold inlet port.

Valve Installation Instructions
3B For 1/2″ Copper Tube Soldering

Solder water supply tube to the valve body. Note: Prior to soldering remove check stops, pressure balancing cartridge and diverter cartridge. Remove check stops by loosening hex nut counterclockwise. Remove the pressure balancing cartridge and diverter cartridge by unscrewing retaining nut with an adjustable wrench. Avoid soldering excessively at high temperature.

4 Flushing

Remove two round mudguards by turning counterclosewise. Remove the rough-in box.

5 Flushing

Remove pressure balancing cartridge by unscrewing retaining nut with an adjustable wrench. Slowly turn on both hot and cold supplies and flush out the valve body and lines. Close the check stops and reinstall the cartridge.

Valve Installation Instructions
6 Pressure Testing

With both check stops in the fully OPEN position, turn on cold and hot water supplies and conduct a system water pressure leak test. Note: To protect the valve, keep mudguards and rough-in box on during installation. Remove only when you are ready to install trims.

Open Close

Open Close

7

Use the rough-in box as a template to cut the wall properly.

8

Reinstall rough-in box , two round mudguards by turning clockwise and complete the wall finish

installation.

Note: In keeping with standard plumbing

practices it is essential that all tub/shower

systems be tested extensively for leaks before

the finishing wall, (tile, etc.) is completed.

Also ensure that the check stops are exposed,

(not covered by tile, boarding etc.) under the

removable trim plate. The trim plate should

completely cover the rough-in opening when

attached. (Having access to these stops allow

you to stop the water flow to your shower

system without turning off the water to the

rest of the bathroom or home.)

Trim Installation Instructions
1

Remove two round mud guards by turning counter-closewise and discard. Remove the rough-in box and discard.

2

Screw small decorative tube(1) over the diverter valve and slide large decorative tube(2) and

cartridge cover(3) onto the pressure balancing

valve.

1

4 5

Use water to wet the round rubber gaskets on

the cover plate(4) and slide cover plate over(4)

6

two decorative tubes. Gently press cover plate(4)

against the finished wall.

Screw the Gear Cipher Adapter(5) on the diverter

cartridge.

2

3

Install cartridge handle(6) and diverter handle(7). Secure by tightening set screw by using the

supplied Allen Wrench. Cover the hole with the

7

supplied plug.

3

When firmly securing the trim plate onto the wall, apply a thin layer of silicone sealant around its

perimeter to prevent water splashes from entering

the wall.

Make sure not to apply it to the back of the trim

plate, in order to avoid potential issues during

future disassembly.

Cleaning and Maintenace Instructions

1

Remove cartridge handle(7), diverter handle(6) and Gear Cipher Adapter(5).

Remove the trim panel(4).

Remove the decorative ring(1) and decorative

1

4 5

sleeve tube(2).

6

2

3

7

2

Using light force only, turn 2 check stops clockwise to close the check stops with the flat head

screwdriver, until you feel resistance, the check

stops are in the closed position.

Close

Close

3

Remove the retaining nut using an adjustable wrench.

Use two fingers to grasp the stem of the cartridge

and wiggle, then pull out.

Shake cartridge and ensure that a clicking sound

is heard, which means the pressure balancing

spool moves freely and works properly.

You may soak the cartridge in 50-50 vinegar/water

mix to remove any calcium and mineral build-up.

Replace the cartridge if it is damaged.

Shower Head and Shower Arm Instructions

1

SHUT OFF WATER SUPPLIES. Consider the type and the thickness of your

finished wall before placing your stringer back

plate.

Finished wall

Install the threaded adapter (Not supplied) so the

surface of the finished wall is flush with the front

of the threaded adapter.

Flush with the finished wall

Make sure that 1/2″ threaded adapter is installed securely inside the wall.

2

Slide escutcheon over shower arm, and apply Teflon tape onto male threads.

3

Screw the shower arm into threaded adapter. Screw the shower head onto the shower arm and

tighten with an adjustable wrench.

Hand Shower Holder Instructions

1

SHUT OFF WATER SUPPLIES. Please note the wall type and thickness before

positioning the stringer back plate. Attach the 1/2″

NPT nipple (Not supplied) in a manner that allows

1/2″(13mm)

it to extend 1/2″ (13 mm) beyond the finished wall

surface.

1/2″-14 NPT Finished wall

2
1/2″(13mm)
3

Wrap plumber’s tape around the threaded ends of the 1/2″ (13 mm) pipe nipple (not provided), then proceed to attach the Quick Connect onto the pipe nipple’s threaded end.
Place the escutcheon over the hand shower holder, then attach the hand shower holder to the quick connect. Secure it in place using the provided Allen key.

Tub Spout Instructions
1
Finished wall Flush with the finished wall

SHUT OFF WATER SUPPLIES. Consider the type and the thickness of your finished wall before placing your stringer back plate. Install the threaded adapter (Not supplied) so the surface of the finished wall is flush with the front of the threaded adapter. Make sure that 1/2″ threaded adapter is installed securely inside the wall.

2

Slide escutcheon over tub spout, and apply Teflon tape onto male threads.

3

Screw tub spout into the threaded adapter.

Limited Lifetime Warranty
Thank you for choosing our faucets and accessories. We are dedicated to providing you with exceptional products that are built to last. CASA FIXTURES is proud to offer a comprehensive limited lifetime warranty on our kitchen and bathroom faucets and accessories. Here are the details of our warranty policy:
CASA FIXTURES warrants the structure and finish of the faucets and accessories to be free from defects in material and workmanship under normal usage for as long as the original purchaser resides in the residence in which the product was first installed. Additionally, the following warranty periods apply to specific components:
· Sprayhead Assembly: CASA FIXTURES warrants the sprayhead assembly, including the engine, aerators, structure, restrictors, backflow preventers, sprayer hoses, and braided supply line hoses (nylon, silicon, and stainless steel), to be free from defects in material and workmanship under normal usage for a period of one (1) year from the date of purchase.
· Cartridge: CASA FIXTURES warrants the faucet’s cartridge to be free from defects in material and workmanship under normal usage for a period of five (5) years from the date of purchase.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>