Banggood ET8508 Multifunctional Network Cable Tester Instruction Manual

: September 23, 2024
: banggood

Table of Contents

Banggood ET8508 Multifunctional Network Cable Tester
Product Usage Instructions
Safety Tips
Characteristic
Introduction
Product Introduction
Product Operation
SPECIFICATIONS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Banggood ET8508 Multifunctional Network Cable Tester

Specifications

Compliance: IEC1010
Voltage Range: 36V
AC/DC Voltage Measurement: Up to 1000V
Current Measurement: Up to 10A
Distance Measurement: Up to 10KM
Power Source: USB, 5V/2A
Dimensions: 1878634mm (Main Unit), 1974736mm (Receiver)

Product Usage Instructions

Safety Tips

This product is designed according to IEC1010 safety standards.
Please read the safety precautions and technical indicators before use.
Read the product technical specifications carefully before measuring any voltage greater than 36V.
Products with multimeter functions can measure AC/DC voltage and current greater than 36V under safety operation requirements.
Products without multimeter function must not measure voltages greater than 36V (except for POE devices) to avoid electric shock.
Avoid inputting a current exceeding 10A.
When changing the function and range, keep the test lead away from the test point to prevent misoperation.
Choose the correct function and range to ensure accurate measurements.
Avoid exposing the red laser emitted by the product to eyes for safety reasons.

Product Operation
The product features various functions such as cable testing network scanning, and voltage measurements.
Ensure proper connections between the tester and the cables or devices being tested.

FAQ
Q: Can this tester measure both AC and DC voltages?
A: Yes, the tester can measure both AC and DC voltages up to 1000V.

Safety Tips

This product is designed according to IEC1010 (safety standard issued by the International Electrotechnical Commission). Please read the safety precautions and technical indicators before use. Please read the product technical specifications carefully before measuring any voltage greater than 36V. Only products with multimeter functions can measure AC/DC voltage and current greater than 36V under the premise of complying with safety operation requirements. Products without multimeter function must not measure voltages greater than 36V (except for POE devices), otherwise there will be a risk of electric shock;

Voltages below 36V are safe voltages. When measuring voltages higher than 36V DC or 25V AC, check whether the test leads are in reliable contact, correctly connected, and well insulated to avoid electric shock.
When measuring the product length, the other end of the network cable cannot be connected to the device, otherwise the device may be damaged. Other network interfaces support a maximum of 60V for normal operation
When measuring voltage, do not input a voltage exceeding the effective value of 1000V DC or 750V AC; when measuring current, do not input a current exceeding 10A;
When changing the function and range, the test lead should be away from the test point;
Choose the correct function and range, and be careful to avoid misoperation. Although this series of instruments has full-range protection function, for the sake of safety, please still pay more attention;
This product emits red laser, please do not expose it to eyes;

Characteristic

With up to 11 professional functions, you can enjoy worry-free engineering with this machine;
Network cable length measurement, up to 600 meters
Powerful network cable analysis function: open circuit, short circuit, crossover and crystal head crimping test
Professional multifunctional multimeter, display up to 60. 000 digits (only available in upgraded models )
Design of 6dBm to -70dBm optical power meter
Red laser emission function, optical fiber transmission distance is about 10KM
Digital line-finding function design is noise-free
Innovative engineering accounting function, which can keep up to 100 length records and calculate network costs
The default 4-language design better meets user needs
The host and line finder can be powered by rechargeable lithium batteries, which is more environmentally friendly

Introduction

This product is a practical tool for network, communication line installation, and engineering maintenance personnel. Its main functions include a multi- function network cable tester (cable tracing, length measurement, POE test, port flashing, crystal head crimping QC test) , multimeter, optical power meter, and VFL. It is a comprehensive test instrument innovatively developed based on long-term engineering practice experience.
The product has the characteristics of long transmission distance, clear sound, fast and accurate length measurement and high precision of multimeter function. The product consists of a signal transmitter, a cable finder and corresponding adapter cables. It is an essential tool for finding cables during construction projects and daily maintenance of various metal lines such as computer network cables, telecommunication network cables, and video network cables.

Product Introduction

Product Operation

Function selection Function

After the product is turned on, this window will appear, and the window will list all the functions of the product; Single-click or long-press the key to selec a function, and click the OK key to enter the function;

Function operation window
Each function of the product has a specific operation window, which will prompt the connection location and operation of the test cable;| In the function operation window, click the return key to return to the main function selection window (Function)

Length measurement (LENGTH)
This function can measure various cables (more than two cores), including network cables, telephone cables, and coaxial video cables. When measuring, the other end of the line must be suspended and cannot be connected to any device; otherwise, the product may be burned directly. Click the V button to select different types of connections: 8 -core Ethernet \4-core Ethernet\telephone linelvideo line; The length measurement accuracy is 2% 1M. When measuring non-standard lines, user calibration is required to ensure accuracy.

Length calibration (CAL)
Different cables have different conductivity, which is different from the national standard cables, so the measurement results will also be biased. In order to accurately measure various cables, this product is designed with a user self-calibration function. Here’s how to do it:

Enter the length measurement function and press A to select the corresponding cable type, connect the cable of known length to the interface, press OK for 2 seconds, the product enters the user self- calibration function mode, the screen displays CAL and flashes the display data, the user can click a or to adjust the measurement result to be consistent with the actual length; after confirming that it is correct, press OK for 2 seconds, the product saves the calibration value, press other keys to exit the calibration mode, and do not save the calibration data. Calibration of subsequent measurements will get more accurate results;
Turn on the machine and select the length function. Press the OK button for 2 seconds without making any adjustments. Press the OK button again for 2 seconds to clear the user calibration data and restore the product to factory settings.
During calibration, the reference line used must be at least 5 meters long;

CABLE WIREMAP (WIREMAP)
This function can test the open circuit, line sequence, short circuit, cross and other connection characteristics of the cable. Plug the network cable into the host and the other end into the “RJ45” socket of the receiver. (After about 5 seconds) the host will display the test results as shown below to determine the connection status of the line. Open (1.2)/Cross (3. 4) Short (5. 8) /Normal (6. 7. G

WIRE TRACKER (SCAN)
This function can quickly find the target line among many line pairs. Connect one end of the line (such as network line, telephone line and video signal line that can be transferred by alligator clip) to the host, the receiver select the SCAN function, and listen to the “beep” sound emitted by the receiver speaker around the other end of the line to be tested (such as line terminal telephone system distribution frame, junction box, computer network hub end). Compare the size of the “beep” sound, and the line with the loudest sound is the target line.

The found line can be connected to the RJ45 interface of the interface device, and the STATE light will light up to further confirm that the target cable is correct.

Crystal plug crimping (QC)
This function may test the quality of cable crimping. You need to turn on the machine and select the function first, and wait for the CAL SETUP self- calibration on the screen to complete; Insert the cable into the host according to the interface instructions. Do not connect any device to the other end of the cable. Insert or unplug the test cable, and the results will be automatically updated. / indicates that the crimping of the crystal connector is normal, and X indicates failure.

*Note: This function tests whether the network cable crystal head is crimped normally, and cannot test the line sequence. To test the line sequence, please use the line alignment function; For the crystal head crimping test, the network cable length must be greater than 20cm, otherwise it may be misjudged.

Optical Power (OPM)

Optical power meter can test the optical signal power and attenuation value. Click▲ to select wavelength; Click ▼A to turn on/off the REF function for testing the attenuation value. Click OK, and the product will hold the current measurement result. Input a standard signal (known power value, press the OK button for 2 seconds, the user can calibrate the optical power meter, the display will show “CAL”, Click or press 2s ▼A/▲ button to adjust (or reset factory value without adjustment), and then press the OK button for 2 seconds to save the calibration result.

Red light pen (VFL)

This function can emit a red laser By connecting the laser to the optical fiber the user can observe the luminous point at the other end of the optical fiber to locate the target among many optical fibers Click the key to switch between different

Port flash (FLASH)
This function can drive the network switch LED to flash, so as to determine the specific port of the target cable; Insert both ends of the network cable into the host and switch ports respectively. Driven by the signal of this product, the corresponding LED lights of the switch ports will flash at intervals of about 3 seconds. Users can determine the target by observing the LED on the switch.

Remote ID (ID)
Select the remote line (ID) identification function; connect one end of the network cable to the ID identifier (optional accessory) and the other end to the host. The host will test and display the corresponding ID number in a timely manner, so as to accurately determine the serial number of the remote network cable; * Remote ID is an optional function;

PoE Measurement (PoE)
The PoE voltage measurement function of the product can measure and analyze the power supply of Poe power supply equipment and test the basic conditions of POE equipment, including the power supply voltage and the positive and negative of the power supply line. Plug the network cable into the host socket and connect the other end to the PoE power supply device. The product will detect the device and enter the corresponding communication as needed and then display the test results; for non- standard PoE, it will directly measure and display the power supply voltage.
Note: connecting a PoE device, the result will be displayed. If the result is not display after 30 seconds, the connected device may not be a PoE device. The actual output voltage of POE will be different from the nominal voltage, which is normal.

Multimeter (DMM)
The product multimeter has multi- functions and 60, 000-digit readings, and its functions and accuracy are comparable to professional multimeters. The product has AC voltage, DCV, ACV, A, on-off buzzer, diode, resistance, capacitance, and frequency functions; The product will automatically detect DC current and AC current, and the user does not need to select. The NCV voltage sensing function is achieved through the line finder; *This feature is only available on upgraded models

Accounting (ACCOUNT)
The product accounting function is innovatively developed for cost accounting of network cabling functions; The product can record the length of up to 100 network cables and calculate the corresponding total cost based on the unit price; Click OK to save data, press ▲ or ▼ to select data; press the up and down keys simultaneously for 2 seconds to clear data; Click the power button to select the unit price and unit adjustment. After selecting the adjustment position, use the ▲/▼ keys to adjust the corresponding parameters.

SETUP SETUP
Product SETUP function, users can select language, screen brightness, automatic shutdown time, turn on/off sound and bright characters on the front of the product; Use the A/Y keys to select the setting item, and the OK key to switch the setting content;