navLinkz VL2-CIC-F 7 Inch Mmonitor Owner’s Manual

: September 23, 2024
: NavLinkz

Table of Contents

navLinkz VL2-CIC-F 7 Inch Mmonitor
Product Information
Product Usage Instructions
Prior to installation
Connection schema
Monitor operation
Specifications
Technical Support
Read User Manual Online (PDF format)
Download This Manual (PDF format)

navLinkz VL2-CIC-F 7 Inch Mmonitor

Product Information

Specifications:

Model: MR-700
Screen Size: 7 inches
Aspect Ratio: 16:9
Resolution: High Definition
Video Inputs: 2 with separate triggers

Product Usage Instructions

Prior to Installation
Read the manual thoroughly before installation. Ensure you have the necessary technical knowledge for proper installation. Place the monitor in a location free of moisture and away from excessive heat.

Delivery Contents
Make sure to note down the serial number of the monitor for support purposes.

Monitor Dimensions
Refer to the manual for detailed monitor dimensions.

Connection Schema

Follow these steps for proper connection:

Connect the female 8pin connector of the monitor-to-monitor cable to the male 8pin connector.
Connect the red wire ACC IN 12V/24V to a stable +12V ACC or +24V ACC.
Connect the black wire of the 8-pin monitor cable to the vehicle ground.
Connect green trigger input Trigger Input 1 12V/24V to the appropriate trigger signal of +12V or +24V.
Connect grey trigger input Trigger Input 2 12V/24V to the appropriate trigger signal of +12V or +24V.
Connect male 4pin connector of the 4pin mini-DIN cable to female 4pin connector Input 1 of the 8pin monitor cable.
Connect male yellow video RCA connector of (A)V-source 1 to female yellow video RCA connector of 4-pin mini-DIN cable.
Connect available audio output of the (A)V-source to female red audio RCA connector.
Connect power supply and ground lead(s) of connected (A)V-source(s) to the red (+12V max. 1A) and black (ground) power output leads of the 4-pin mini-DIN cable.

FAQ :

Q: Is it safe to watch videos while driving using this monitor?
A: No, it is prohibited by law to watch moving pictures while driving. The monitor should only be used to display fixed menus or rear-view camera video when the vehicle is in motion.

7inch monitor

MR-700

High-resolution digital 7 inch 16:9 HD-monitor with 2 video inputs with separate triggers

Product features

2 switchable video inputs e.g., for rear view camera and front camera
Video inputs AHD (720p, 960p, 1080p) and CVBS compatible
Video inputs NTSC and PAL compatible
Switchable via permanent- or pulse voltage
Automatic switch-on and switch-off via switching inputs
Separate audio inputs for both video inputs
Integrated mono speaker
Guide-lines activatable
Last position memory (switching on in last mode)
Inputs with system connector 4P for cameras with 4-pin mini-DIN with CV assignment
1 adapter to RCA included
Car and truck compatible (12V/24V) with 12V power supply for cameras
Adjustable picture cut-off delay for both video inputs
Mirroring and rotation of camera picture on both video inputs separately selectable
Automatic dimming of display brightness adjustable

Legal Information
By law, watching moving pictures while driving is prohibited, the driver must not be distracted. We do not accept any liability for material damage or personal injury resulting, directly or indirectly, from installation or operation of this product. Apart from using this product in an unmoved vehicle, it should only be used to display fixed menus or rear-view-camera video when the vehicle is moving (for example the MP3 menu for DVD upgrades).

Prior to installation

Read the manual prior to installation. Technical knowledge is necessary for installation. The monitor’s place of installation must be free of moisture and away from excessive heat.

Delivery contents

Monitor dimensions

Connection schema

Connection – 8pin monitor cable (Power)

Connect female 8pin connector of monitor-to-monitor cable’s male 8pin connector.
Connect red wire “ACC IN 12V/24V” to stable +12V ACC or +24V ACC.
Note: The fuse- and reducer box in the power line supplies the monitor and the 4pin mini-DIN system ports for (A)V-sources with +12V max. 2.5A, regardless of whether the connection to vehicle is to +12V or +24V.
Connect the black wire of the 8-pin monitor cable to vehicle ground.

Connection – 8pin monitor cable (trigger inputs)

Connect green trigger input “Trigger Input 1 12V/24V” to a for the (A)V source connected to the green 4pin mini-DIN system ports appropriate trigger signal of +12V or +24V (example reverse gear signal for the rear-view camera).
Note : Activation via trigger inputs also works with pulsed voltage. In this case, it is suspended again after the pulse frequency has stopped (e.g., turn signal).
Connect grey trigger input “Trigger Input 2 12V/24V” to a for the (A)V source connected to the green 4pin mini-DIN system ports appropriate trigger signal of +12V or +24V.
Note: If both inputs are triggered at the same time, (A)V-source 1 is priority.

Connection – (A)V-source with 4pin mini-DIN cable

Connect male 4pin connector of 4pin mini-DIN cable to female 4pin connector “Input 1” of 8pin monitor cable (connection of a second (A)V-source is possible with an optional 4-pin mini-DIN cable to “Input 2”).
Connect male yellow video RCA connector of (A)V-source 1 to female yellow video RCA connector of 4-pin mini-DIN cable. Connect available audio output of the (A)V-source to female red audio RCA connector.
Connect power supply and ground lead(s) of connected (A)V-source(s) to the red (+12V max. 1A) and black (ground) power output leads of the 4-pin mini-DIN cable.

Connection – camera with 4pin mini-DIN connector (without RCA)

Connect male 4pin mini-DIN connector of the optionally in desired length available CAB-RV4-xxS system extension cable to female 4pin mini-DIN connector “Input 1” of 8-pin monitor cable (connection of another camera or (A)V-source possible to “Input 2”).
Connect camera’s male 4-pin mini-DIN connector with screw cap to female 4-pin mini-DIN connector (+12V max. 1A) of optionally available CAB-RV4-xxS system extension cable and tighten screw.

Connection – Shutter camera with 4pin mini-DIN cable

Connect male 4pin connector of 4pin mini-DIN cable to female 4pin connector “Input 1” of 8pin monitor cable (connection of another camera or (A)V-source to “Input 2” is possible).
Connect yellow video and white audio male RCA connectors of adapter cable CAB-4P-RCA-SH to yellow video and white audio female RCA connectors of 4pin mini-DIN cable CAB-2RCAFPW-4PM.
Connect green (black) wire of adapter cable CAB-4P-RCA-SH to red (black) wire (+12V max. 1A) of 4pin mini-DIN cable CAB-2RCAFPW-4PM.
Connect male 4pin mini-DIN connector of optionally in desired length available CAB-RV4-xxS system extension cable to female 4pin mini-DIN connector of adapter cable CAB-4P-RCA-SH and connect the other end to male 4pin mini-DIN screw connector of shutter camera and tighten screw.

Monitor operation

Power: “POWER” key turns monitor off or on. The monitor supports “last position memory”. When the monitor is shut off (powered on) while switching off ACC, the monitor will start shut off (powered on) next time ACC is turned on. It also remembers the last selected (A)V-source.
Source selection: “MODE” key switches between V1 and V2
OSD-menu: “MENU” key opens OSD-menu

“MENU” key then changes between menu pages VIDEO, CAR, SYSTEM; AUDIO
“MENU” key in AUDIO menu closes OSD-menu
“MODE” key moves cursor down in current menu
“UP” and “DOWN” keys change values of menu item the cursor is on

Menu items in VIDEO menu page

Brightness (0 – 100)
Contrast (0 – 100)
Saturation (0 – 100) Tint (0 – 100)
Reset (factory settings)

Menu items in CAR menu page

V1 guide line for source 1 (ON/OFF)
V2 guide line for source 2 (ON/OFF)
Picture delay time for source 1 (OFF/0- 10 sec)
Picture delay time for source 2 (OFF/0- 10 sec)

Menu items in SYSTEM menu page

Choosing language (English/Deutsch)
Rotating picture both inputs (ON/OFF)
Mirroring of source 1 image (ON/OFF)
Mirroring of source 2 image (ON/OFF)
Brightness dependant dimmer (ON/OFF)
Manual dimmer (0 – 100)

Menu items in AUDIO menu page

Volume of internal speaker (0 – 100)

Specifications

Monitor type 7inch AHD/CVBS monitor
Operating voltage range 9V – 30V
Stand-by power drain (when shut off) approx. 110mA @ 12V
Operating current (monitor only) approx. 300mA @12V
Maximum camera power current V1/V2 2A @ 12V total (1A/input)
Maximum current (incl. camera power) 2.5A @12V
Video input voltage 0.7V – 1V
Video input TV-standard NTSC/PAL
Video input signal type AHD (720p, 960p, 1080p) or CVBS
Temperature range -40°C to +85°C
Dimensions (monitor without holder) 173 x 115.5 x 23 mm (W x H x D)

Technical Support

Please note that direct technical support is only available for products purchased directly from NavLinkz GmbH. For products bought from other sources, contact your vendor for technical support.

NavLinkz GmbH
Distribution/tech dealer support