ELECCTV BW6-N Wire Free Camera Instruction Manual
- May 15, 2024
- ELECCTV
Table of Contents
Wire-Free Camera
Operation Instruction
(BW6)
BW6-N Wire Free Camera
Customer Service
Claim
1-year
warranty for your device
Please email us:
Phone:
+1 2027384449
(Sun. – Thur. 8pm – 12pm)| Facebook
Rraycomz@gmail.com
---|---
Packing List
- Camera *1
- Bracket *1
- USB Cable *1
- Instruction*1
- Mounting Kit *1
Appearance
BW6
At the bottom
Indicator light definition
Reset| Green light flashes
Charging| Red light
Fully Charged| Off
No network| Blue light flashes
Wifi connected| Blue (when it wakes up)
Sleep| Off
Quick start
Power-on
Press and hold the power button until you hear the prompt,
Reset
Press and hold the reset button for about 3 seconds,
Step-1 >>> Download the APP
Scan the QR code to download the APP. Or search for “O-KAM” to download
through the app store (Google play/ APP Store).
https://www.veepai.com/veecam_download.html
Step-2 >>> APP account registration
1. Click “Register now” at the login interface
— Select the address
— Enter your phone number
— Get the verification code.
2. After entering the verification code you need to set the password and
click Finish. Step-3 >>> Add cameras
1. Log in and click “Add” button found at the “Home” interfaceor click the
” ” in the upper right corner. Step-4 >>> Add cameras
At the QR code scanning interface, scan the QR code on the camera.
3. Switch the camera “On”.
(No need for “Long press”)
Click “Next” when the indicator light flashes in blue slowly.
4. Confirm that the camera is ready for WiFi configuration when the indicator
light flashes in blue slowly. And click “Next” 5. Enable the location service
of your phone, and allow the O-KAM APP to access the location. Confirm the
WiFi and enter the
- Make sure the Wi-Fi is 2.4Ghz. WiFi 6. The APP will automatically generate a QR code. Point the camera lens at the QR code and keep it at a distance of 6-8 inches. You’ ll hear a beep and voice prompt when it’s scanned successfully. 7. When the device is connected to the WiFi, name the camera and click “Bind Now”.8. Please take the camera and phone to the location where you’re going to install the camera, and then click “Next” to test the signal strength. Make sure there is strong WiFi signal strength at the location. Step-5 >>> APP function introduction Step-6 >>> Monitoring settings
Enter system settings ” ” -monitoring function
Tap on the “Device Health”- “Firmware”to update (Suggested) Step-7 >>> Share the device
Enter the system settings ” “- Share
Sharing method: Share the QR code to a user. The other user adds the camera by scanning the QR code;The QR code is valid for 30 minutes, and one QR code can only be shared with one user. Generate more QR codes for more members. Maximum of 4 people can live view at the same time. Tutorial Videos
Please scan the QR code below
https://www.rraycom.com/blogs/news/user-guide-for-bw4-and-bw5
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception,which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>