Shuttle XH610G Slim Mini PC 1L Barebone User Guide

: September 20, 2024
: Shuttle

Table of Contents

Shuttle XH610G Slim Mini PC 1L Barebone
Product Overview
Hardware Installation
Safety Information
Motherboard Illustration
Jumper Settings
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Shuttle XH610G Slim Mini PC 1L Barebone

Specifications :

Memory Support: 1.1 V DDR5 SO-DIMM
Storage Support: HDD or SSD
M.2 Support: M.2 2280 (NVMe+SATA, SATA only), M.2 2230 E key slot
Expansion Card Support: PCIe x16 (max size: 208.5 mm x 120 mm x 30 mm)

Product Overview:
The XH610G is a versatile motherboard with support for various components including memory modules, storage devices, M.2 devices, and expansion cards. It features multiple ports for connectivity and is designed for easy installation of components.

Memory Module Installation:

Locate the SO-DIMM and paste the thermal pad on the motherboard to reduce temperature.
Align the notch of the memory module with the relevant memory slot.
Insert the module into the slot at a 45-degree angle and push down until it snaps into place.

HDD or SSD Installation:

Disconnect the power cord before opening the case.
Unscrew and remove the HDD/SSD cover.
Install the memory module if required.
Insert the HDD or SSD in the chassis using its bracket and connect with an HDD/SSD cable.

M.2 Device Installation :

Locate the M.2 key slots on the motherboard.
Install the M.2 device into the slot and secure with a screw.

How to Change the Battery:

Gently pry the metal tab to disengage the battery from the holder.
Install the new battery with the positive side facing up.

Installation of Expansion Card:

Unfasten the expansion slot bracket screw and remove the back panel bracket.
Install the PCIe x16 card into the slot and secure the bracket.

Note :

The product’s color and specifications may vary from the actually shipped product.

FAQ :

Q: Can I use DDR4 memory modules instead of DDR5 on this motherboard?
A: No, this motherboard only supports 1.1 V DDR5 SO-DIMM memory modules.
Q: What is the maximum size of display cards supported?
A: The maximum permitted size for display cards is 208.5 mm x 120 mm x 30 mm. They must be installed on the riser card, not on the motherboard.

Guide rapid
More information on this product can be found at: https://bit.ly/S-XH610G

Product Overview

USB 2.0 Ports
USB 3.2 Gen1 Type-A Ports
MIC-in
Headphones
Power switch / Power LED
Hard disk drive LED
COM port (optional)
HDMI 2.0 Ports
DisplayPort
2.5Giga LAN Port
Giga LAN Port
. Power Jack (DC IN)
Clear CMOS & Power Button & +5V
Wireless LAN perforation (optional)
PCIe x16 slot
Kensington® Lock hole

Hardware Installation

A. HDD or SSD Installation
For safety reasons, please ensure that the power cord is disconnected before opening the case.

Turn your XH610G upside down, then unscrew three screws of the HDD/SSD cover and remove it. Install the memory module (thermal pad 50 x 15 x 2.25 mm for DIMMB2 slot), if required (refer step C).
Mount the HDD/SSD into the bracket with three screws
Tear off the adhesive tape of the HDD cable. Install the HDD or SSD in the chassis using its bracket. Affix with three screws and connect the HDD or SSD with an HDD/SSD cable
Replace the HDD/SSD cover and refasten three screws

B. CPU and ICE Module Installation

Unscrew the two thumbscrews of the chassis cover. Slide the cover backwards and upwards.
Unfasten the four ICE module attachment screws and unplug the fan connector. Remove the ICE module from the chassis and put it aside.
- Follow the steps below to correctly install the CPU into the motherboard CPU socket
- This CPU socket is fragile and can easily be damaged. Always use extreme care when installing a CPU and limit the number of times you remove or change the CPU. Before installing the CPU, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage of the CPU.
Unlock and raise the socket lever
Lift the metal load plate off the CPU socket
DO NOT touch the socket contacts. To protect the CPU socket, always use the protective socket covver when the CPU is not installed.
Please orientate the CPU correctly and align the CPU notches with the socket alignment keys. Make sure the CPU sits perfectly horizontal, then push it gently into the socket
Please be aware of the CPU orientation, DO NOT force the CPU into the socket to avoid bending of pins on the socket and damage of CPU!
Tear off the protective membrane from the metal load plate. Close the metal load plate, lower the CPU socket lever and lock in place.
Spread the thermal paste evenly on the CPU surface
Please do not apply excess amount of thermal paste.
Screw the ICE module to the motherboard. Note to press down on the opposite diagonal corner while tightening each screw.
Connect the fan.

C Memory Module Installation

This motherboard does only support 1.1 V DDR5 SO-DIMM ! memory modules.

Locate the SO-DIMM and paste the thermal pad on the motherboard, which can effectively reduce its temperature
Align the notch of the memory module with the one of the relevant memory slot
Gently insert the module into the slot in a 45-degree angle
Carefully push down the memory module until it snaps into the locking mechanism

D. M.2 Device Installation

Locate the M.2 key slots on the motherboard.
Install the M.2 device into the M.2 slot and secure with the screw.

E. How to change the battery

Use a flat-blade screwdriver to gently pry the metal tab to disengage the battery from the battery holder.
Install the new battery, press it on the battery holder keeping the positive side facing top.

F. Installation of Expansion Card

Unfasten the expansion slot bracket screw. Remove the back panel bracket and put it aside.
Install the PCIe x16 card into the PCIe x16 slot. Secure the bracket

G. Complete

Replace the cover and tighten the thumbscrews, then connect the power cord.
Complete

H. Installation of VESA Mount

Follow the steps 1-2 to install the VESA mount
Supports 75×75 mm and 100×100 mm VESA standard

Safety Information

Incorrectly replacing the battery may damage this computer. Replace only with the same or equivalent as recommended by Shuttle. Dispose of used batteries in accordance with the laws of your country.

All bundled parts, power cord included, shall not be used without this product

The equipment was evaluated for use in a maximum air ambient temperature of 40 ºC.
2000m

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.

This device meets the requirements for the EU conformity in accordance to the currently valid EU directives

WARNING THIS PRODUCT CONTAINS A BUTTON BATTERY

If swallowed, a lithium button battery can cause severe or fatal injuries within 2 hours. Keep batteries out of reach of children. If you think batteries may have been swallowed or placed inside any part of the body, seek immediate medical attention

The statement “remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. Do NOT dispose of batteries in household trash or incinerate.”
- Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. Do NOT dispose of batteries in household trash or incinerate.
- Even used batteries may cause severe injury or death.
- Call a local poison control center for treatment information.
- Indicating the compatible battery type CR2032.
- Indicating the nominal battery voltage.
- Non-rechargeable batteries are not to be recharged.
- Do not force discharge, recharge, disassemble, heat above (manufacturer’s specified temperature rating) or incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in chemical burns.
This Product contains a button Battery/coin cell batteries
- Ensure the batteries are installed correctly according to polarity (+ and -).
- Do not mix old and new batteries, different brands or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries.
- Remove and immediately recycle or dispose of batteries from equipment not used for an extended period of time according to local regulations.
- Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.

Product Overview

USB 2.0 ports
USB 3.2 Gen1 Type-A Ports
MIC-in
Headphones
Power switch / Power LED
Hard disk drive LED
COM port (optional)
HDMI 2.0 Ports
DisplayPort
Giga LAN Port
Clear CMOS & Power button & +5V
Perforation for optional WLAN (optional)
2.5Giga LAN Port
Power Jack (DC IN)
PCIe x16 slot
Kensington® Lock hole

HDD or SSD Installation

For safety reasons, please ensure that the power cord is disconnected before opening the case.

Turn your XH610G upside down, then unscrew three screws of the HDD/SSD cover and remove it. Install the memory module (thermal pad 50 x 15 x 2.25 mm for DIMMB2 slot), if required (refer step C).
Mount the HDD/SSD into the bracket with three screws.
Tear off the adhesive tape of the HDD cable. Install the HDD or SSD in the chassis using its bracket. Affix with three screws and connect the HDD or SSD with an HDD/SSD cable
The product’s colour and specifications may vary from the actually shipped product.
Replace the HDD/SSD cover and refasten three screws

CPU and ICE Installation

Unscrew the two thumbscrews of the chassis cover. Slide the cover backwards and upwards.
Unfasten the four ICE module attachment screws and unplug the fan connector. Remove the ICE module from the chassis and put it aside
Follow the steps below to correctly install the CPU into the motherboard
This CPU socket is fragile and can easily be damaged. Always use extreme care when installing a CPU and limit the number of times you remove or change the CPU. Before installing the CPU, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage of the CPU.CPU socket
Unlock and raise the socket lever.
Lift the metal load plate off the CPU socket
DO NOT touch the socket contacts. To protect the CPU socket, always use the protective socket cover when the CPU is not installed.
Please orientate the CPU correctly and align the CPU notches with the socket alignment keys. Make sure the CPU sits perfectly horizontal, then push it gently into the socket.
Please be aware of the CPU orientation, DO NOT force the CPU into the socket to avoid bending of pins on the socket and damage of CPU!

Install the M.2 device into the M.2 slot and secure with the screw

E. How to change the battery

Use a flat-blade screwdriver to gently pry the metal tab to disengage the battery from the battery holder.
Install the new battery by pressing it on to the battery holder keeping the positive pole facing up.

F. Installation of Expansion Card

Unfasten the expansion slot bracket screws.
Remove the back panel bracket and put it aside
The maximum permitted size for display cards is 208.5 mm x 120 mm x 30 mm.
The display cards must be installed on the riser card, not on the motherboard
Install the PCIe x16 card into the PCIe x16 slot. Secure the bracket.

G. Complete