Shuttle DH670 Drives Four Displays with 12th Generation User Guide

June 3, 2024
Shuttle

Shuttle DH670 Drives Four Displays with 12th Generation

More information on this product can be found at: http://bit.ly/S-DH670

Product Overview

  1. MIC-in
  2.  Headphones
  3.  Power LED
  4.  Hard disk drive LED
  5. Power Button
  6.  SD Card Reader (Option)
  7. USB 3.2 Gen1 Type-A Ports
  8.  USB 3.2 Gen2 Type-A Ports
  9.  USB 3.2 Gen1 Type-C Port
  10.  Kensington® Lock Hole
  11. HDMI 2.0 Ports
  12.  Power Jack (DC IN)
  13. DisplayPort
  14. LAN Ports
  15. COM 1 Port (RS232/RS422/RS485)
  16.  COM 2 Port (RS232 only)
  17.  Clear CMOS & Power Button & +5V

Hardware Installation

Begin Installation
For safety reasons, please ensure that the power cord is disconnected before opening the case.

  1. Unscrew the two screws of the chassis cover. Slide the cover backward and upwards.
  2. Unfasten the rack mount screw and remove the rack.

CPU and ICE Module Installation

  1. Unfasten the four ICE module attachment screws and unplug the fan connector. Remove the ICE module from the chassis and put it aside

  2. Follow the steps below to correctly install the CPU into the motherboard CPU socket This CPU socket is fragile and can easily be damaged. Always use extreme care when installing a CPU and limit the number of times you remove or change the CPU. Before installing the CPU, make sure to turn off
    the computer and unplug the power cord from the power outlet to prevent damage to the CPU. Unlock and raise the socket lever.

  3. Lift the metal load plate of the CPU socket. DO NOT touch the socket contacts. To protect the CPU socket, always use the protective socket cover
    when the CPU is not installed.

  4. Please orientate the CPU correctly and align the CPU notches with the socket alignment keys. Make sure the CPU sits perfectly horizontal, then push it gently into the socket.

  5. Tear off the protective membrane from the metal load plate. Close the metal load plate, lower the CPU socket lever, and lock it in place.

  6. Spread the thermal paste evenly on the CPU surface. Please do not apply an excessive amount of thermal paste.

  7. Screw the ICE module to the motherboard. Note to press down on the opposite diagonal corner while tightening each screw.

  8.  Connect the fan.

Memory Module Installation

This motherboard does only support 1.2 V DDR4 SO-DIMM memory modules

  1. Locate the SO-DIMM slots on the motherboard.
  2.  Align the notch of the memory module with one of the relevant memory slots.
  3. Gently insert the module into the slot in a 45-degree angle.
  4.  Carefully push down the memory module until it snaps into the locking mechanism.
  5. Repeat the above steps to install an additional memory module, if required.

Device Installation

  1. Locate the M.2 key slots on the motherboard
  2. Install the M.2 device into the M.2 slot and secure with the screw M.2 2242/2260/2280 M key slot

Pasting the supplied thermal pad on the M.2 SSD can effectively reduce its temperature

When installing M.2 2242 M-key and M.2 2230 E-key at the same time, please use “M.2 shared nut” (see picture) to lock M.2 2230 E-key card on the socket, then install M.2 2242 M-key card by M2*3 screw as the next step

HDD or SSD Installation

  1. Place an HDD or SSD in the rack and secure it with the four screws from the sides.
  2. Slide the rack back into the chassis and refasten the screw. Connect the Serial ATA and power cable to the HDD or SSD.

Complete

  1. Please replace and affix the case cover with two screws, then connect the power cord.
  2. Complete.

Please press the “Del” key while booting to enter BIOS. Here, please load the optimized BIOS settings.

Safety Information

Incorrectly replacing the battery may damage this computer. Replace only with the same or equivalent as recommended by Shuttle. Dispose of used batteries according to the manufacturer’s instructions All bundled parts, power cord included, shall not be used without this product This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions this device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation.

Product Overview

  1. MIC-in
  2. Headphones
  3. Power LED
  4. Hard disk drive LED
  5. Power Button
  6. SD Card Reader (Option)
  7. USB 3.2 Gen1 Type-A Ports
  8. USB 3.2 Gen2 Type-A Ports
  9. USB 3.2 Gen1 Type-C Port
  10. Kensington® Lock Hole
  11. HDMI 2.0 Ports
  12. Power Jack (DC IN)
  13. DisplayPort
  14. LAN Ports
  15. COM 1 Port
  16. COM 2 Port (RS232 only)
  17. Clear CMOS & Power Button & +5V

Memory Module Installation

This motherboard does only support 1.2 V DDR4 SO-DIMM memory modules.

  1. Locate the SO-DIMM slots on the motherboard
  2. Align the notch of the memory module with one of the relevant memory slot
  3. Gently insert the module into the slot in a 45-degree angle.
  4. Carefully push down the memory module until it snaps into the locking mechanism. Please be aware of the CPU orientation, DO NOT force the CPU into the socket to avoid the bending of pins on the socket and damage to the CPU!
  5. Tear off the protective membrane from the metal load plate. Close the metal load plate, lower the CPU socket lever, and lock it in place.
  6. Spread the thermal paste evenly on the CPU surface.
  7. Screw the ICE module to the motherboard. Note to press down on the opposite diagonal corner while tightening each screw

CPU and ICE Installation

  1. Unfasten the four ICE module attachment screws and unplug the fan connector. Remove the ICE module from the chassis and put it aside.
  2. Unlock and raise the socket lever
  3. Lift the metal load plate of the CPU socket.
  4. Please orientate the CPU correctly and align the CPU notches with the socket alignment keys. Make sure the CPU sits perfectly horizontal, then push it gently into the socket.

Device Installation

  1. Locate the M.2 key slots on the motherboard.
  2. Install the M.2 device into the M.2 slot and secure it with the screw

HDD or SSD Installation

  1. Place an HDD or SSD in the rack and secure it with the four screws from the sides.
  2. Slide the rack back into the chassis and refasten the screw. Connect the Serial ATA and power cable to the HDD or SSD.

Complete

  1. Please replace and affix the case cover with two screws, then connect the power cord.
  2. Complete.

Motherboard Illustration

  1. USB 3.2 Gen2 Type-A Ports
  2. USB 3.2 Gen1 Type-A Ports
  3. USB 3.2 Gen1 Type-C Port
  4. SD Card Reader (Option)
  5. Power Button
  6. Hard disk drive LED
  7. Power LED
  8. Headphones
  9. MIC-in
  10. SATA connector
  11. DDR4 SO-DIMM slots
  12. Processor socket LGA1700
  13. Intel® H670 Chipset
  14. M.2 2242/2260/2280 M key slot
  15. M.2 2230 E key slot (supports CNVi)
  16. Power Jack (DC IN) \ DC
  17. HDMI 2.0 Ports
  18. DisplayPort
  19. LAN Ports
  20. Battery connector

Jumper Settings

Fan connector

VGA connector

COM 1 & COM 2 power switch
COM PORT Pin 9 “Ring Indicator” (RI) configuration

Configure COM 1 with the first jumper

  •  Short Pin 1-2: Pin 9 = RI1 (default)
  •  Short Pin 5-7: Pin 9 = +5V
  •  Short Pin 7-9: Pin 9 = +12V

Configure COM 2 with the second jumper

  • Short Pin 3-4: Pin 9 = RI2 (default)
  •  Short Pin 6-8: Pin 9 = +5V
  •  Short Pin 8-10: Pin 9 = +12V

COM port \ COM

COM port

AC auto power-on

USB 2.0 cable connector

Clear CMOS & power button & +5V

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals