Kruger Matz KMP-AD1 Wireless earphones Owner’s Manual

Kruger Matz KMP-AD1 Wireless earphones

SAFETY INFORMATION

• Minimize the volume on your audio device before connecting the earphones in order to avoid hearing damage from sudden exposure to excessive volume. Keep the volume at a reasonable level throughout entire time of using the earphones. To prevent damage to your hearing, do not raise the volume too high.
• Do not use the earphones in places where the inability to hear ambient sound presents a serious risk (such as at railroad crossings, train stations, construction sites or on roads where vehicles and bicycles are traveling). Never use the earphones while driving a car, riding a motorcycle or bicycle or operating any other vehicle, as it may cause potential risk to your safety.
• Wireless devices can cause interference in aircraft. Please make sure that your earphones are powered off in flight.
• Follow any special regulations in force in any area such as hospitals and always switch off your earphones whenever it is forbidden to use it or, when it may cause interference or danger.
• Follow basic safety precautions while using the earphones.
• Stop using the earphones if you feel a tinnitus, hearing discomfort, irritation or have other adverse reactions.
• Do not subject the earphones to strong impact.
• Keep this product away from children.
• Protect this product from moisture, humidity, water and any other liquid. Avoid using/ storing it in extreme temperatures. Do not expose it to direct sunlight and sources of heat.
• Never use this device if it is damaged.
• Use only authorized accessories.
• Do not use fast charger to charge the case.
• Do not attempt to repair this device yourself. In case of damage, contact with an authorized service point for checkup/ repair.
• Turn off the earphones before cleaning.
• Clean this device with soft, slightly damp cloth. Do not use any abrasives or chemical agents to clean this product.

PRODUCT DESCRIPTION

1. micro USB charging port
2. Earphone charging indicator
3. Charging case indicator
4. Button (manually start charging)
5. LED indicator
6. MFB button

PAIRING

1. Remove the earphones from the charging case. The earphones should turn on automatically. The earphones should automatically pair with each other. LED should flash red and blue.
   • If the battery in the charging case is empty or if the earphones will not turn on automatically, it is required to turn on the earphones manually by pressing the MFB for 3 seconds on both earphones.
2. After the earphones pair with each other, they will enter Bluetooth pairing mode (blue LED on the right (master) earphone flashes every 2 seconds).
3. Enable the Bluetooth function on the external device and search for new Bluetooth devices.
4. Select and connect with this device (KMP-AD1). Voice prompt indicates successful pairing. LED on right earphone goes off.

Notes:

• Every time the earphones are switched on, they will connect to last connected device automatically. Please note, your device must be on with Bluetooth function turned on.
• If the earphones are not connected to any device, they will automatically power off after about 3 minutes.

OPERATION

CHARGING

EARPHONES
The charging case has a built-in battery. When it is fully charged, it is possible to charge earphones maximally 3 times.

1. Place both earphones in the charging case. Make sure to align the charging contacts correctly on the earphones and the charging case. Charging should start automatically.*
2. During charging red LED on the earphones is on. When the battery is fully charged, red LED goes off.
3. During charging blue LED on the charging case is on. When charging is finished, blue LED goes off.
   If charging does not start automatically, you can press the button on the charging case to start manually.

CHARGING CASE
Use charging case to store and charge your earphones.

1. Insert one plug of the USB cable to the micro USB port of the charging case. Insert the other plug to the compatible PC USB port or AC adapter.

2. During charging red LED on the charging case flashes.
   When the battery is fully charged, red LED is on.

3. It takes about 2 hours to fully charge the battery.*
   When earphones with not fully charged battery are placed inside the case during charging, charging time may increase.

SPECIFICATION

• Speaker size: 6 mm
• Magnet: neodymium
• Frequency response: 20 Hz – 20 kHz
• Impedance: 32 Ohm
• S/N ratio: >=92 dB
• THD: <1% (1 kHz)
• Bluetooth version: 5.0
• Bluetooth range: up to 10 m
• Bluetooth profiles: A2DP, AVCTP, AVRCP, HFP, HSP, SPP, GAP,SDP, L2CAP
• Built in microphone
• Microphone sensitivity: -38 dB +/-3 dB
• Voice call management
• Music playback
• Playback time: up to 4 h
• Talk time: up to 4 h
• Standby time: up to 150 h
• Battery capacity: 35 mAh (earbuds); 300 mAh (charging case)
• Charging voltage: 5 V/1 A
• In set: charging case, USB cable, user’s manual

LEARN MORE
For more information on this product, go to www.krugermatz.com.
Visit www.krugermatz.com website for more products and accessories.
In case of any doubts or questions reach out to our Frequently Asked Questions section.

Lechpol Electronics Sp. z o.o. Sp.k. hereby declares that Wireless Earphones KMP-AD1 is consistent with directive 2014/53/UE.
Full text of the EU Declaration of Conformity is available at following Internet address: www.lechpol.eu.

Correct Disposal of This Product
(Waste Electrical & Electronic Equipment) (Applicablein the European Unionan do ther European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.
Made in China for LECHPOL ELECTRONICS Sp.

www.krugermatz.com
is a registered trademark

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>