UNICOL PSU Bespoke Projector Bracket Instruction Manual
- September 20, 2024
- UNICOL
Table of Contents
PSU Bespoke Projector Bracket
“`html
Specifications
- Max. Projector Weight: 60kg
- Please check model specific details before installing
Product Usage Instructions
PSU Installation
STEP 1 (Inverted Installation)
Loosen the 2 x Hex M8 or M10 hex screws and disconnect the upper
and lower parts of the PSU.
The upper part of a PSU (T-Bar) generally fits to a column or
peg connected to a ceiling plate or wall arm. The lower part fixes
to an inverted projector. Cables run through column or peg and
sockets to projector.
STEP 2
Using the fixing screws provided, fit the lower part of the PSU
to the fixing holes of the inverted projector.
PSC Installation
STEP 1 (Cradle Installation)
Loosen the 2 x Hex M8 or M10 hex screws and disconnect the upper
and lower parts of the PSC.
The upper part of a PSC (T-Bar) generally fits to a column or
peg connected to a ceiling plate or wall arm. The lower part acts
as a cradle to house the projector. Cables run through column or
peg and sockets to projector.
Rest the projector on its feet in the base of the cradle.
PPSU Installation
STEP 1 (Portrait Installation)
Loosen the 2 x Hex M8 or M10 hex screws and disconnect the upper
and lower parts of the PPSU.
The upper part of a PPSU generally fits to a column or peg
connected to a ceiling plate or wall arm. The lower part fixes to a
projector on its side. Cables run through column or peg and sockets
to projector.
STEP 2
Using the fixing screws provided, fit the lower part of the PPSU
to the fixing holes of the projector, on its side, lens pointing
horizontally.
VSU Installation
STEP 1 (Vertical Installation)
Loosen the 2 x Hex M8 or M10 hex screws and disconnect the upper
and lower parts of the VSU.
The upper part of a VSU generally fits to a column or peg
connected to a ceiling plate or wall arm. The lower part fixes to a
projector on its side. Cables run through column or peg and sockets
to projector.
STEP 2
Using the fixing screws provided, fit the lower part of the VSU
to the fixing holes of the projector, on its side, lens pointing
downward.
FAQ
Q: Do I need any special tools for installation?
A: Yes, you will need a 3/16th Allen Key, 13mm Spanner (for M8),
17mm Spanner (for M10), and a Pozidrive Screwdriver.
“`
01865 767676 sales@unicol.com
www.unicol.com
PSU / PSC / PPSU / VSU
PSU
PPSU
PSC
VSU
Guide Max. Projector Weight: 60kg Please check model specific details before installing
Revised 15/05/23
WARNING
Please carefully inspect the product before assembling. If you notice any
apparent damage, call your carrier claims agent and do not continue the
installation until it has been reviewed. Please watch for pinch points. Do not
put your fingers between moveable parts. Do not tamper with or disassemble any
spring loaded parts. Before installing, make sure that the supporting surface
will support five times the combined load of the solution and the hardware.
Never exceed the maximum load capacity. Please also layout all components to
ensure that you have all of the required parts before proceeding (see BOM list
on following page). Use of this product for anything other than its specified
use may result in failure or personal injury. This product is intended for
indoor use only. We recommend using a qualified trades person for
installation. Use an assistant or lifting equipment to lift and position
products. For support, please call: +44 (0)1865 767676 or email:
sales@unicol.com
01865 767676 sales@unicol.com
www.unicol.com
TOOLS REQUIRED
1 3/16th Allen Key
2 13mm Spanner (for M8)
3 17mm Spanner (for M10)
4 Pozidrive Screwdriver
COMPONENTS
9 10
1 11
INSTALLERS REQUIRED
1-2
5
7
6
8
12 2
2 3
4
DESCRIPTION
1 PSU – Socket & Bar Assembly
2 PSU – Dedicated Projector Fixing Plate
3 PSC – Socket & Bar Assembly
4 PSC – Dedicated Projector Cradle
5 PPSU – Socket & Bar Assembly
6 PPSU – Dedicated Projector Fixing Plate
7 VSU – Socket & Bar Assembly
8 VSU – Dedicated Projector Fixing Plate
9 Heavy duty T-Bar
Dedicated Projector Fixing Screws
10 Ceiling Plate
11 Adapter
12 Column
QTY 1 1 1 1 1 1 1 1 1 # 1 1 1
Revised 15/05/23
01865 767676 sales@unicol.com
www.unicol.com
PSU
STEP 1 (inverted installation)
Loosen the 2 x Hex M8 or M10 hex screws and disconnect the upper and lower
parts of the PSU.
The upper part of a PSU (T-Bar) generally fits to a column or peg connected to
a ceiling plate or wall arm. The lower part fixes to an inverted projector.
Cables run through column or peg and sockets to projector. (Alternative T-Bar
shown for heavier projectors)
STEP 2
Using the fixing screws provided fit the lower part of the PSU to the fixing
holes of the inverted projector.
The plate fixing to the projector is designed specifically for the projector
ordered so may look differently to the one shown.
PSC
STEP 1 (cradle installation)
STEP 2
Loosen the 2 x Hex M8 or M10 hex screws and disconnect the upper and lower
parts of the PSC.
The upper part of a PSC (T-Bar) generally fits to a column or peg connected to
a ceiling plate or wall arm. The lower part acts as a cradle to house the
projector. Cables run through column or peg and sockets to projector.
Rest the projector on its feet in the base of the cradle.
Each cradle is manufactured to suit the projector you have ordered the mount
for. Balance and ventilation is taken into account within the design.
Revised 15/05/23
3
PPSU
01865 767676 sales@unicol.com
www.unicol.com
STEP 1 (portrait installation)
STEP 2
Loosen the 2 x Hex M8 or M10 hex screws and disconnect the upper and lower
parts of the PPSU.
The upper part of a PPSU generally fits to a column or peg connected to a
ceiling plate or wall arm. The lower part fixes to a projector on its side.
Cables run through column or peg and sockets to projector.
Using the fixing screws provided fit the lower part of the PPSU to the fixing
holes of the projector, on its side, lens pointing horizontally.
The plate fixing to the projector is designed specifically for the projector
ordered so may look differently to the one shown.
VSU
STEP 1 (vertical installation)
STEP 2
Loosen the 2 x Hex M8 or M10 hex screws and disconnect the upper and lower
parts of the VSU.
The upper part of a VSU generally fits to a column or peg connected to a
ceiling plate or wall arm. The lower part fixes to a projector on its side.
Cables run through column or peg and sockets to projector.
Using the fixing screws provided fit the lower part of the VSU to the fixing
holes of the projector, on its side, lens pointing downward.
The plate fixing to the projector is designed specifically for the projector
ordered so may look differently to the one shown.
4
Revised 15/05/23
CEILING SUSPENSION
01865 767676 sales@unicol.com
www.unicol.com
STEP 1 (typical installation shown)
Remove through-bolt in upper part of bar assembly socket and loosen grub
screws. Align socket with column or peg. Thread cables through socket. Insert
through-bolt and tighten. Tighten grub screws.
Safety through-bolts must be used to secure the unit. Grub screws are used to
remove slack in the joint.
STEP 2 (PSU shown)
Hook lower part with projector over the 2 x M8/M10 hex screws. Cable up
projector and set tilt angles then tighten M8/M10 hex screws. Set rotation
angle by turning projector either way to finish installation.
Beware of stretching cables when adjusting angles.
STEP 3 (PSC shown)
Hook lower part with projector over the 2 x M8/M10 hex screws. Cable up
projector and set tilt angles then tighten M8/M10 hex screws. Set rotation
angle by turning projector either way to finish installation.
Beware of stretching cables when adjusting angles.
STEP 4 (PPSU & VSU shown)
Hook lower part with projector over the 2 x M8/M10 hex screws. Cable up
projector and set tilt angles then tighten M8/M10 hex screws. Set rotation
angle by turning projector either way to finish installation.
Beware of stretching cables when adjusting angles.
Revised 15/05/23
5
01865 767676 sales@unicol.com
www.unicol.com
6
Revised 15/05/23
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>