UNICOL PLA1X1 Wall Arms User Manual

June 24, 2024
UNICOL

UNICOL PLA1X1 Wall Arms User Manual

UNICOL-PLA1X1-Wall-Arms-User-Manual-product

Product Specifications

  • PLA1X1:
    • Screen Size: 33-57 inches
    • Guide Max. Weight: 30kg
  • PLS1X1 SRV:
    • Screen Size: 15-32 inches
    • Guide Max. Weight: 20kg

Product Usage Instructions

PLS & PLA Installation

  1. Using the 3 mounting holes in the back plate, determine the installation position and fix using suitable anchors & screws.
  2. Ensure the wall is capable of supporting 5x the combined weight of the mount and screen.
  3. Mount the screen onto the PLS or PLA using the provided PZX Universal mount according to separate instructions.
  4. Fix the PZX backplate to the head of the PLS/PLA using the M25 hex head screws provided.
  5. Adjust the screen tilt angle using the allen key provided by rotating the knurled adjuster on the rear of the mount. Clockwise tilts upwards.
  6. Level the screen by rotating it clockwise or anticlockwise.
  7. Cable up the screen using cable ties through the holes in the arms.

SRV & SSV Installation

  1. Using the 2 mounting holes in the back plate, determine the installation position and fix using suitable anchors & screws.
  2. Ensure the wall is capable of supporting 5x the combined weight of the mount and screen.
  3. Fix your screen to the mounting plate with appropriate screws, using VESA 100×100 or 100×200 fixing holes.
  4. Adjust the screen tilt angle using the knurled adjuster on the rear of the mount. Clockwise tilts upwards.
  5. Level the screen by rotating it clockwise or anticlockwise.
  6. Cable up the screen using cable ties through the holes in the arms.

Wall Arms – PLA & PLS – SSV & SRV

WARNING

Please carefully inspect the product before assembling it. If you notice any apparent damage, call your carrier claims agent and do not continue the installation until it has been reviewed. Please watch for pinch points. Do not put your fingers between moveable parts. Do not tamper with or disassemble any spring-loaded parts. Before installing, make sure that the supporting surface will support five times the combined load of the solution and the hardware. Never exceed the maximum load capacity. Please also layout all components to ensure that you have all of the required parts before proceeding (see BOM list on following page). Use of this product for anything other than its specified use may result in failure or personal injury. This product is intended for indoor use only. We recommend using a qualified tradesperson for installation. Use an assistant lifting equipment to lift and position products.
For support, please call: +44 (0)1865 767676 or email: sales@unicol.com

TOOLS REQUIRED

UNICOL-PLA1X1-Wall-Arms-User-Manual-fig-1

COMPONENTS

UNICOL-PLA1X1-Wall-Arms-User-Manual-fig-2

PLS & PLA

STEP 1 – (PLS & PLA)
Using the 3 mounting holes in the back plate, determine where you want to install your mount, mark and fix it into position using suitable anchors & screws. Please consider cabling and wall fixings prior to installation. Please check surface is capable of supporting 5x the weight of the combined solution.

STEP 2 – (PLS & PLA)
A separate universal mount (PZX) is provided to mount your screen to the PLS or PLA. Separate instructions are provided with each screen mount. Follow these to mount your screen onto the mount backplate. Fix the PZX backplate to the head of the PLS/PLA using the M25 hex head screws provided.

UNICOL-PLA1X1-Wall-Arms-User-Manual-fig-3

STEP 3 – (PLS & PLA)
There is fine adjustment of the screen tilt angle using the allen key provided to rotate the knurled adjuster on the rear of the mount. Turn clockwise to tilt upwards. STEP 4 – (PLS & PLA)
The screen can be leveled slightly by rotating the screen clockwise or anticlockwise.
Cable up your screen using cable ties through the holes in the arms. The PLA has extra tags on the elbow of the first arm for this purpose.

SRV & SSV

STEP 1 – (SRV & SSV)
Using the 2 mounting holes in the back plate, determine where you want to install your mount, mark and fix it into position using suitable anchors & screws.
Please consider cabling and wall fixings before installation. Please check surface is capable of supporting 5x the combined solution weight.

STEP 2 – (SRV & SSV)
Fix your screen to the mounting plate shown above with the appropriate screws. There are fixing holes for VESA 100×100 and 100×200.

Contact Us

01865 767676
sales@unicol.com
www.unicol.com

Frequently Asked Questions

Q: Do I need any special tools for installation? A: Yes, you will need a 3/16th Allen Key, a Pozidrive Screwdriver, and a 17mm Spanner as mentioned in the manual.

Q: How do I know if my surface can support the weight of the mount and screen? A: Please ensure your wall is capable of supporting at least 5 times the combined weight of the mount and screen before installation.

Q: How do I adjust the tilt angle of the screen? A: Use the provided tools to adjust the tilt angle by rotating the knurled adjuster on the rear of the mount. Clockwise tilts upwards.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals