UNICOL PZX0 Pozimount Non Tilting Wall Mount Instruction Manual

July 4, 2024
UNICOL

PZX0 / PZX1 / PZX3 / PZX5 / PZX9 / PPZX2
PPZX9 / PZW0 / PZW1 / PZW3 / PZW8UNICOL PZX0 Pozimount Non Tilting Wall
Mount

Please check model specific details before installing
Screen Size: 33 – 110” Guide Max. Weight: 60-120kg
Revised 14/12/20

WARNING

Please carefully inspect the product before assembling. If you notice any apparent damage, call your carrier claims agent and do not continue the installation until it has been reviewed. Please watch for pinch points. Do not put your fingers between moveable parts. Do not tamper with or disassemble any spring loaded parts. Before installing, make sure that the supporting surface will support five times the combined load of the solution and the hardware. Never exceed the maximum load capacity. Please also layout all components to ensure that you have all of the required parts before proceeding (see BOM list on following page). Use of this product for anything other than its specified use may result in failure or personal injury. This product is intended for indoor use only. We recommend using a qualified trades person for installation. Use an assistant or lifting equipment to lift and position products. For support, please call: +44 (0)1865 767676 or email: sales@unicol.com

| TOOLS REQUIRED

---|---
1| Pozi Head Screwdriver

| OPTIONAL

1| 13mm Spanner (adjusting tension in tilting arms)

INSTALLERS REQUIRED
1-2

COMPONENTS

UNICOL PZX0 Pozimount Non Tilting Wall Mount -
COMPONENTS

WALL FIXING

STEP 1
Using the 4 – 8 wall mounting slots cut out on the back plate, determine where you want to install your mount, mark it and fix into position. Please consider cabling and wall fixings prior to installation. Please check surface is capable of supporting 5x the combined solutions weight.

UNICOL PZX0 Pozimount Non Tilting Wall Mount - fixing
pack

STEP 2
Utilising the tag locks and fixing pack provided with your mount, attach the arms to the back of your screen.
Ensure the arms are the correct way up before tightening – the ‘hook’ part of the arm should be at the top.

STEP 3
Using another team member, lift the screen up and gradually offer it up to the back plate. Gently tilting the screen forward, hook the arms over the lip of the back plate and lower once in position.
Centre the screen horizontally by sliding from side to side until you are happy with the position.

UNICOL PZX0 Pozimount Non Tilting Wall Mount - fixing pack
2 STEP 4
Once centered, ensure the bottom screws are not screwed tight and screw down the top screws to level the screen. Once level tighten bottom screws to secure the mount. ALT: If using tilting arms, this is when you can adjust them to suit.
Note that you won’t be able to adjust the screens position after the screws have been tightened.

STAND / TROLLEY

UNICOL PZX0 Pozimount Non Tilting Wall Mount -TROLLEY STEP 1
Line the back plate up with the mount adapter, as shown above. Fix 4 screws from behind the mount adapter and into the 4 rivet nuts located on the back plate. Ensure back plate is secure and screws are tightened.

UNICOL PZX0 Pozimount Non Tilting Wall Mount -TROLLEY
1

STEP 2
Utilising the tag locks and fixing pack provided with your mount, attach the arms to the back of your screen. Ensure the arms are the correct way up before tightening – the ‘hook’ part of the arm should be at the top.

STEP 3
Using another team member, lift the screen up and gradually offer it up to the back plate. Gently tilting the screen forward, hook the arms over the lip of the back plate and lower once in position.
Centre the screen horizontally by sliding from side to side until you are happy with the position.

UNICOL PZX0 Pozimount Non Tilting Wall Mount -screws STEP 4
Once centered, ensure the bottom screws are not screwed tight and screw down the top screws to level the screen. Once level tighten bottom screws to secure the mount. ALT: If using tilting arms, this is when you can adjust them to suit.
Note that you won’t be able to adjust the screens position after the screws have been tightened.

01865 767676
sales@unicol.com
www.unicol.com

Documents / Resources

| UNICOL PZX0 Pozimount Non Tilting Wall Mount [pdf] Instruction Manual
PZX0, PZX1, PZX3, PZX5, PZX9, PPZX2, PPZX9, PZW0, PZW1, PZW3, PZW8, PZX0 Pozimount Non Tilting Wall Mount, PZX0, Pozimount Non Tilting Wall Mount, Non Tilting Wall Mount, Tilting Wall Mount, Wall Mount
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals