UNICOL PFT1 Series LED and TFD Monitors Plasma and Projectors Instruction Manual

September 20, 2024
UNICOL

PFT1 Series LED and TFD Monitors Plasma and Projectors

“`html

Product Information:

Specifications:

  • Product Models: PFT1, PFT3, PFT4, PFT9, PFT21
  • Screen Size: 33-110 inches
  • Maximum Weight Capacity: 120kg

Product Usage Instructions:

Tools Required:

  1. 5mm Allen Key
  2. Pozidrive Screwdriver
  3. 17mm Spanner / Socket

Installers Required:

1-2 installers

Components:

  1. Base
  2. Mast
  3. Screen Mount Backplate
  4. Screen Mount Arms

Installation Steps:

  1. Step 1: Identify the base and place it on a
    solid surface.

  2. Step 2: Attach the mast to the base using the
    provided screws.

  3. Step 3: Mount the screen backplate to the mast
    and adjust the height position of the screen.

  4. Step 4: Attach the screen mount arms to the
    back of your screen.

  5. Step 5: Lift the screen with help and place
    the arms onto the backplate, adjusting the position.

  6. Step 6: Secure the bottom of the screen by
    tightening screws and level the screen.

  7. Step 7: Cable up and carry out a functional
    test to complete installation.

Frequently Asked Questions (FAQ):

Q: How much weight can the product support?

A: The product has a maximum weight capacity of
120kg. Please check model-specific details before installation.

Q: What tools are required for
installation?

A: You will need a 5mm Allen Key, Pozidrive
Screwdriver, and a 17mm Spanner or Socket.

“`

01865 767676 sales@unicol.com
www.unicol.com
PFT1 / PFT3 / PFT4 / PFT9 / PFT21

Screen Size: 33-110″

Guide Max. Weight: 120kg

Please check model specific details before installing

Revised 22/03/23

WARNING
Please carefully inspect the product before assembling. If you notice any apparent damage, call your carrier claims agent and do not continue the installation until it has been reviewed. Please watch for pinch points. Do not put your fingers between moveable parts. Do not tamper with or disassemble any spring loaded parts. Before installing, make sure that the supporting surface will support five times the combined load of the solution and the hardware. Never exceed the maximum load capacity. Please also layout all components to ensure that you have all of the required parts before proceeding (see BOM list on following page). Use of this product for anything other than its specified use may result in failure or personal injury. This product is intended for indoor use only. We recommend using a qualified trades person for installation. Use an assistant or lifting equipment to lift and position products.
For support, please call: +44 (0)1865 767676 or email: sales@unicol.com

01865 767676 sales@unicol.com
www.unicol.com

TOOLS REQUIRED

1 5mm Allen Key

2 Pozidrive Screwdriver

3 17mm Spanner / Socket

INSTALLERS REQUIRED
1-2

COMPONENTS

3 2

4 1

DESCRIPTION

1 Base 2 Mast 3 Screen Mount Backplate 4 Screen Mount Arms

QTY
1 1 1 2

2

Revised 22/03/23

01865 767676 sales@unicol.com
www.unicol.com

STEP 1 Identify base and place on a solid surface.

STEP 2
Fit mast to base using the 4 x M8 x 20 dome head allen screws provided. Screw into mast from under the base.

Griplocks

Taglocks

STEP 3
Fit the screen mount backplate to the mast using the 4 x M10 x 25 hex screws provided.
The height position of the screen is dependent on which holes are used in the mast. Remember to leave enough room for the screen to fit above the base. There is also height adjustment on the screen mount arms if further adjustment is required.

STEP 4
Utilising the grip locks (top), tag locks (bottom) and fixing pack provided with your mount, attach the arms to the back of your screen.
Ensure the arms are the correct way up before tightening – the `hook’ part of the arm should be at the top.

Revised 22/03/23

3

01865 767676 sales@unicol.com
www.unicol.com

STEP 5
Dependent on screen size and weight, with the help of another, lift the screen with top tilted forward and place the hook part of the arms onto the top rail of the backplate. Allow the screen arms to rest on the backplate vertically. While still holding the screen position it centrally on the top rail by sliding it side to side.

STEP 6
The bottom of the screen is secured by screwing the bottom arm pozidrive screws so they impinge on the bottom rail of the backplate (do not fully tighten yet).
There is a small amount of adjustment to level the screen by tightening or loosening one or both top arm screws. Once level tighten all arm screws.

STEP 7 Cable up and carry out functional test to complete installation.
4

Revised 22/03/23

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals