UNICOL KP320DB Ceiling Suspension Trade Pack Instruction Manual
- June 25, 2024
- UNICOL
Table of Contents
KP KITS
Screen Size: 33-70” Guide Max. Weight: 45-60kg
Please check model specific details before installing
Revised 15/12/20
WARNING
Please carefully inspect the product before assembling. If you notice any
apparent damage, call your carrier claims agent and do not continue the
installation until it has been reviewed. Please watch for pinch points. Do not
put your fingers between moveable parts. Do not tamper with or disassemble any
spring loaded parts. Before installing, make sure that the supporting surface
will support five times the combined load of the solution and the hardware.
Never exceed the maximum load capacity. Please also layout all components to
ensure that you have all of the required parts before proceeding (see BOM list
on following page). Use of this product for anything other than its specified
use may result in failure or personal injury. This product is intended for
indoor use only. We recommend using a qualified trades person for
installation. Use an assistant or lifting equipment to lift and position
products.
For support, please call: +44 (0)1865 767676 or email:
sales@unicol.com
# | TOOLS REQUIRED |
---|---|
1 | Pozi Head Screwdriver |
2 | 3/16th Allen Key |
3 | 13mm Spanner |
INSTALLERS REQUIRED
1-2
COMPONENTS
# | DESCRIPTION | QTY |
---|---|---|
1 | Length of Column (1m, 2m or 3m) | 1 |
2 | CP1 Standard Ceiling Plate | 1 |
3 | Single Sided Suspension Mount | 1 |
4 | Universal Tilting Mount Arms | 2 |
5 | Alternative Suspension Mount | – |
6 | Alternative Ceiling Plate | – |
STEP 1
Using the 4 ceiling mounting slots, as shown above, determine where you want
to install your mount, mark it and fix into position.
Please consider cabling and ceiling fixings prior to installation. Please
check surface is capable of supporting 5x the combined solutions weight.
STEP 2
Slide all cabling through the column and through the gap in the ceiling
plate socket. Being mindful of the cables, slide the column into the socket,
ensuring that the two holes either side align with those on the mount. Using
the through bolt, secure the column into place and tighten the two grub screws
at the rear. STEP 3
Slot cabling through the suspension mount socket and slide the mount over the
column, ensuring that the two holes either side align with those on the
column. Like in Step 2, slide the through bolt through the holes and secure.
Tighten the two grub screws at the rear. STEP 4
Utilising the tag locks and fixing pack provided with your mount, attach
the arms to the back of your screen.
Ensure the arms are the correct way up before tightening – the ‘hook’ part of
the arm should be at the top. STEP 3
Using another team member, lift the screen up and gradually offer it up to the
back plate. Gently tilting the screen forward, hook the arms over the lip of
the back plate and lower once in position.
Centre the screen horizontally by sliding from side to side until you are
happy with the position. If double sided, repeat this step on the reverse
side. STEP 4
Once centered, ensure the bottom screws are not screwed tight and screw
down the top screws to level the screen. Once level tighten bottom screws to
secure the mount. This is when you can adjust the tilitng arms to suit.
Note that you won’t be able to adjust the screens position after the screws
have been tightened.
WALL ARM STEP 1
Using the wall mounting holes in the back plate, determine where you want to
install your mount, mark it and fix into position.
Please consider cabling and wall fixings prior to installation. Please check
surface is capable of supporting 5x the combined solutions weight. STEP 2
Slide all cabling through the column and through the gap in the wall plate
socket. Being mindful of the cables, slide the column into the socket,
ensuring that the two holes either side align with those on the mount. Using
the through bolt, secure the column into place and tighten the grub screws at
the front of the socket. Continue from Step 3.
01865 767676
sales@unicol.com
www.unicol.com
Revised 15/12/20