Wyze YZECFL2 Floodlight User Guide
- September 19, 2024
- Wyze
Table of Contents
YZECFL2 Floodlight
“`html
Product Specifications:
- Floodlight Screw Bracket Screws: #8
- Microphone
- Speaker
- LED Lamp Camera Status Light
- Motion Sensor
- SETUP button
- Micro SD card slot
Product Usage Instructions:
Setup:
- Download the Wyze app and sign in or create an account.
- Select Add Device > Cameras > Wyze Cam Floodlight v2 and
follow the instructions in the app.
Installation:
Wall Mount:
-
Take the Wyze Cam Floodlight v2 out of the box and rotate the
camera 180 degrees so that the Wyze logo is at the top and the
motion sensor is pointed down. -
Ensure the arrows on the joint arm behind the camera are in
alignment. -
Place the mounting bracket on the junction box and tighten it
using matching bracket screws (Bag C). -
Attach the ground wire to the middle of the mounting bracket
using the ground wire screw (Bag A). -
Connect the hot wire from your junction box to the hot wire of
the floodlight and connect the neutral wires. Cap the wires using
wire nuts. -
Hang the provided hook as shown in the picture.
-
Push the wires back into the junction box ensuring they are not
pinched. -
Screw the floodlight to the mounting bracket using the provided
Floodlight screw (Bag B). -
Adjust the angle of the motion sensor to be parallel to the
ground.
Eave Mount:
- Follow steps 1 and 2 for wall mount installation.
- Tilt the camera slightly up so it faces out and downward when
mounted under eaves.
Frequently Asked Questions (FAQ):
Q: Do I need to consult an electrician for installation?
A: If you are outside of North America, installation and wiring
must be performed by a licensed electrician. It’s recommended to
consult an electrician if you are unsure about wiring.
Q: What is the recommended height for mounting?
A: The Wyze Cam Floodlight v2 should be mounted at least 10 feet
above the ground for optimal motion detection up to 30 feet
away.
“`
Ground Wire Screw × 1 (Bag A)
Floodlight Screw Bracket Screws #8
× 1 (Bag B)
×2 (Bag C)
Microphone
Speaker
Bracket Screws #10 Bracket Screws #6 Rubber Stopper × 1
× 2 (Bag D)
× 2 (Bag E)
LED Lamp Camera Status Light
Motion Sensor
Wire Nuts × 2
Mounting Bracket × 1
SETUP button Micro SD card slot
Hook × 1
Assembled floodlight v2 Camera x 1 1
SETUP
1 Download the Wyze app and sign in or create an account.
2 Select Add Device > Cameras > Wyze Cam Floodlight v2 and follow the
instructions in the app.
overhang under eaves.
3 Check your local laws for installation. If you are outside of North America,
installation and wiring must be performed by a licensed electrician. Make sure
you follow all code standards when doing wire installation.
4 WARNING: Risk of electrical shock! 1. installation. If you need one
installed, please contact a licensed electrician. 2. Verify that the power
supply is a 120 V AC 60 Hz power source. 3. Disconnect power using the fuse or
circuit breaker before continuing. Note: Do not use a dimmer switch or timer
for this product.
WALL MOUNT (refer to pages 2-5)
EAVE MOUNT (refer to pages 5-7)
WALL MOUNT
Recommended Installation Location
Tip: When Wyze Cam Floodlight v2 is mounted 10 feet above the ground, it will
detect motion up to 30 feet away.
10 feet
30 feet
2
1 Take your Wyze Cam Floodlight v2 out of the box. and rotate the camera 180 so that the Wyze logo is at the top and the motion sensor is pointed down.
1 Starting position
2 Tilt lights down
`W’ and arrows on the joint arm behind the camera. Make sure the arrows are in
alignment. Do not rotate the camera completely around as this may twist or
break the connection line.
2 may be attached if you are replacing a previous product.
3 Place the mounting bracket on the junction box. Align the 2 screw holes and
tighten the bracket using matching bracket screws (Bag C).
Rotate the lights 180°
3 Rotate the lights and camera 180°
Junction Box
4 Tilt lights up
electrician to install one and follow local building codes. 3
4 Use the ground wire screw (Bag A) to attach the ground wire to the middle of the mounting bracket.
Use the
Ground wire is usually
ground screw. exposed copper wire
or colored green.
6 to the hot wire from your junction box. Then connect the 2 neutral wires
(usually white). Cap the wires using wire nuts and twist them 5-10 times.
Gently tug on the wire nut to make sure it’s securely attached.
IMPORTANT: If you are not sure which wire is which, please consult an
electrician for safety.
Hold the wires together.
Twist the wire nut 5-10 times.
5 the provided hook as shown in the picture.
7 Push the wires back into the junction box. Make sure the wires are not
pinched between Wyze Cam Floodlight v2 and the mounting bracket.
8 Screw your Wyze Cam Floodlight to the mounting
10 Now adjust the angle of the motion sensor so it is parallel to the ground.
9 protect the screw.
Use the Floodlight screw (Bag B).
The angle should be parallel to the ground.
30 feet
10 feet
EAVE MOUNT
Recommended Installation Location
Tip: When Wyze Cam Floodlight v2 is mounted 10 feet above the ground, it will
detect motion up to 30 feet away.
10 feet
30 feet
4
5
1 Take your Wyze Cam Floodlight v2 out of the box. Raise rotate it 180° to lower the LED lamp.
the `E’ and arrows on the joint arm behind the camera. Make sure the arrows
are in alignment. Do not rotate the camera completely around as this may twist
or break the connection line.
2 Tilt the camera slightly up so the camera is looking out and the motion
sensor is facing out and downward when mounted overhang.
Rotate the camera 180°
1 Starting position
2 Rotate the camera 180°
Motion sensor facing out
3
4 Place the mounting bracket on the junction box. Align the 2 screw holes and
tighten the bracket using matching bracket screwscBag C
.
licensed electrician to install one and follow local building codes.
5 Use the ground wire screw to attach the ground wire to the middle of the
mounting bracket (Bag A).
Use the ground screw.
Ground wire is usually exposed copper wire or colored green.
Caution: Do not force the wires on the mounting bracket
6 provided hook as shown in the picture.
Junction Box
3 Rotate lights up
4 Tilt lights up
6
7
7 Connect the hot wire (usually black) from your
connect the 2 neutral wires (usually white). Cap the wires using wire nuts and
twist them 5-10 times. Gently tug on the wire nut to make sure it’s securely
attached.
IMPORTANT: If you are not sure which wire is which, please consult an
electrician for safety.
Note: The screw and rubber plug installation steps are the same as 8 and 9 for
wall installation.
The next steps are the same for both eave and wall mounting.
Hold the wires together.
Twist the wire nut 5-10 times.
160° view 160°
270°
Motion area for triggering the lights 270°
Note: We recommend leaving the ladder in place until after you’re done pairing the camera(s) and adjusting the
8
8 want it.
9 Restore power to the junction box using the circuit
red. 10 Note: We recommend leaving the ladder in place untilafter light
position.
11 If you need to reinstall the device after removing it in Apps or reset the device please press the SETUP button on the side of the camera for 3 seconds or until a voice prompt happens.
Restore power to the junction box using the circuitbreaker
WYZE CAM FLOODLIGHT STATUS LIGHT GUIDE
Solid red light The device is powered on and initializing
Flashing red light The device is ready to connect
Flashing red & blue lights Connection is in progress
Flashing blue light Solid blue light The device is working properly
9
WARRANTY
Your Wyze product is covered by a one-vear limitedwarranty. You can view the
limited warranty terms athttps://wyze.com/return-warranty-policy or requesta
copy by contacting Wyze at +1(206)339-9646.
SPECIFICATIONS
Model: WYZECFL2 WYZECFL2BL Connectivity: 2.4GHz Wi-Fi Weather Resistance: IP65
Input: Hardwired 120V~50/60Hz 0.61A
Apple logo and App Store are trademarks of Apple Inc., registered in the U.S.
and other countries and regions. Google Assistant, Google Home, Google Play,
and the Google Play logo are trademarks of Google LLC.
Wyze and Wyze Cam Floodlight v2 are trademarks of Wyze Labs, Inc.
FCC WARNING
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including
interference that may cause undesired operation.
Caution: The user is cautioned that changes or modifications not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures: –Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver. –Connect the
equipment into an outlet on a circuit different from that to
which the receiver is connected. –Consult the dealer or an experienced
radio/TV technician for help.
10
RF RADIATION EXPOSURE STATEMENT
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator and any part of your body.
SUPPLIER’S DECLARATION OF CONFORMITY
Brand NameWZYE Model NumberWYZECFL2 Suppliers NameWyze Labs, Inc. Suppliers
Address (USA): 5808 Lake Washington Blvd NE Ste 300 Kirkland WA 98033
Suppliers Phone Number or Internet Contact Information
1-844-999-3226
ISED RSS WARNING
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions: (1)This device
may not cause interference.(2)This device must accept any interference,
including interference that may cause undesired operation of the device.
AVERTISSEMENT DE L’ISED CONCERNANT LES NORMES RSS
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences et Développement économique Canada
applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes: 1. L’appareil ne doit pas produire de
brouillage; 2. L’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
ISED RADIATION EXPOSURE STATEMENT
This equipment complies with ISED RSS-102 radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20cm between the radiator and any part of
your body.
DÉCLARATION D’EXPOSITION AUX RADIATIONS DE LA L’ISED
Pour se conformer aux exigences de conformité CNR 102 RF exposition, une
distance de séparation d’au moins 20cm doit être maintenue entre l’antenne de
cet appareil ettoutes les personnes.
11
NEED HELP?
Contact our Support Team: https://wyze.com/support Join the Community:
https://wyze.com/community
Scan the QR code to learn more
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>