FriFri 670137 Super Easy Built In Fryer Instruction Manual
- June 3, 2024
- FriFri
Table of Contents
FriFri 670137 Super Easy Built In Fryer Instruction Manual
THE MIDDLEBY CORPORATION
Lincat Ltd
Whisby Road
Lincoln
United Kingdom
Tel: +44 (0) 1522 875555
For all fryers of the Super Easy Built-In line per
2. Models and dimensions
2.1 Weights and capacities
2.2 Identification of the appliance
Every deep fryer is provided with a technical identification plate.
Always have this identification plate available when making enquiries to our
customer services department.
2.3 Ambient conditions
2.4 Voltages, types of connection and versions
2.5 Mains fuses
2.6. Electrical connection
This appliance must be installed, commisioned and serviced by a qualified
person in accordance with national and
local regulations in force in the country of installation.
a) Check that the specifications of the electrical mains correspond to those
given on the rating plate. This plate is located on the power box beneath the
tank.
b) Means of isolation with at least 3mm contact separation in all poles must
be incorporated into the fixed wiring
of this appliance. The fixed wiring insulation must be protected by insulated
sleeving having a temperature
range of at least 60 Deg C. Supply cords should be oil resistant, sheathed
flexible cable not lighter than ordinary polychloroprene or equivalent
elastomer sheathed cord (code 6024-IEC 57).
If fitting a mains plug to the supply cable, it should correspond to the rated
input of the appliance and should be
accessible after installing the appliance.
c) An equipotential bonding terminal is provided to allow cross bonding with
other equipment.
d) If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified
persons.
3. Safety regulations
The following warning symbols are fitted to the deep fryer as appropriate:
High voltage
Electric shock
Warning of dangerous electrical voltage
Only authorized specialist personnel may carry out work on electrical
installations.
Follow the specific technical safety instructions.
Always disconnect the appliance from the mains power before carrying out work
on electrical installations,
servicing or cleaning.
Hot surfaces / hot internal components
During operation parts may become hot. Avoid accidental contact.
Hot frying oil
Warning of hot frying oil which can lead to injuries. Always allow the hot
frying oil to cool down before carrying out cleaning or service work.
Advice
The manufacturer has mounted warning symbols (stickers) at all the relevant positions on the appliance before delivery. If during operation or within the scope of cleaning work any of these warning symbols become detached the operator of the appliance is obliged to apply these warning symbols again immediately.
3.1 Specified use of the deep fryer
The appliance is exclusively intended for the frying of fresh and deep-frozen
foods and whilst operating should not be left unsupervised. Any other use of
the appliance is regarded as non-specified. The observance of the operating
manual and the following of the maintenance and repair instructions from the
manufacturer are also part of the specified use.
3.2 Specific warnings and instructions
WARNING
Do not attempt to move the appliance when the tank contains hot oil.
Do not use a water jet or steam cleaner and do not immerse this appliance.
Do not operate without first filling it with fat or frying oil to the maximum
oil level mark.
During operation, maintain the oil level between the maximum and minimum oil
level marks. Too little oil will
result in the safety cut-out operating or the risk of ignition. Overfilling
will cause surging or frothing over.
Used, contaminated frying oil is increasingly likely to ignite and also tends
to froth over. If the frying oil ignites,
do not attempt to extinguish it with water but use a fire extinguisher with a
special filling (Halon) or a fire
blanket.
CAUTION
If too much deep-frozen or wet frying product is put into the hot frying oil,
frothing over may occur.
Overfilling the basket will also reduce the quality of the fried food. For
safe draining or transferring the frying
oil it must have cooled down to a temperature below 50 Deg C.
Never clean the elements with a steel brush or by burning off (dry operation).
Improper cleaning of the
elements will lead to the exclusion of the guarantee.
3.3 Personnel safety
WARNING
The personnel who operate and maintain the appliance must be trained in the correct operation and handling procedures, and must have read and understood the safety regulations in this operating manual before starting work on or with it.
Do not modify or remove safety devices. Do not remove warning symbols which
may have been fitted to the
appliance.
Replace missing or defective warning symbols.
Do not operate the appliance in a damaged condition. Report any
irregulatities, especially those which affect
safety, to your managers.
When servicing components, ensure that the appliance is disconnected from the
mains power supply.
Always check all safety functions after completing service work.
3.4 Safety equipment
Apart from the warning symbols applied to the appliance it is also fitted with
the following safety equipment:
Main switch
Safety contactor
Safety thermostat
3.5 Authorized personnel
Only those personnel who have been authorized for the respective work may work
on and with this appliance.
Personnel are seen as authorized if they fulfil the minimum training and
knowledge requirements as listed in this
section and have been assigned a fixed area of responsibility.
3.6 Area of responsibility of personnel
3.6.1 Owner/operator
The owner/operator is the person who is responsible for the specified use of
the appliance and for the training as
well as the tasks of the authorized personnel, including issuing directives to
all personnel with respect to appliance
operations.
3.6.2 Operator of the appliance
Operator responsibilities include:
Maintaining oil level in the appliance.
Loading the product and monitoring frying quality. Cleaning and filtering.
Identifying and reporting problems.
3.6.3 Maintenance personnel
Carry out maintenance and repair of the appliance according to the work
described in Sections ‘Cleaning and
Maintenance’
Are responsible for the dismantling, storing and disposal of the appliance.
3.7 Minimum training and qualifications of the authorized personnel
3.7.1 Owner/operator
Should have relevant experience in assessing safety and in personnel
management.
Must understand the section “Safety regulations”.
3.7.2 Operator of the appliance
Must be instructed in the operation of the appliance and be aware of safety
regulations.
3.7.3 Service personnel
Must have successfully completed the relevant training and be familiar with
the servicing of the appliance.
Servicing work on the electrical equipment of the appliance must only be
carried out by suitably qualified personnel.
3.8 Duty of maintenance
The appliance must only be used when in an undamaged condition. Use original
consumables and original spare
parts as replacements whenever necessary. Always check the equipment for
safety after maintenance and repair
work.
3.9 Availability of operating manual
A copy of this operating manual must be available at all times to the
personnel at the installation location.
4. Installation and starting up
4.1 Installation of the appliance
Read this part of the brochure carefully and get familiar with the necessary
installation procedure. Check against the delivery documents that the
appliance you have complies with the order.
Before you begin the installation, check against the enclosed packing list that you have all the necessary components.
Unpack the components and lay them out ready to use in the order you will need them.
If the fryer is built-in near another thermal element, make sure that the
control box is ventilated.
( Max. Temperature inside the control box 60ºC )
There are two possible solutions to building-in the frying tank:
Installation of the frying tank with a frame directly integrated into the worktop
The cut out will be reduced by 10mm + the material thickness of the worktop.
You will find the necessary cut out
dimensions at a later stage in these instructions.
Installation of the frying vat with the supplied frame (See drawing at end for
cutout information)
The frame supplied serves to fix the appliance as well as providing protection
against penetration of humidity.
Installation of the controls
Warning: Make sure that the controls are well ventilated. ( Max. Temperature
inside the controls 60ºC )
Warning: If installing from the rear, access for after sales service must be
provided.
4.2 Operation
Remove any remains of packaging and strip plastic coating. Remove the lid of
the tank. Take the basket out of
the tank. Clean the appliance and the accessories with a non caustic cleaning
agent, suitable for use in a food
area. CLOSE THE DRAIN VALVE. Fill the tank with oil to the MAX. level or place
the fat for frying on the heating elements. The MIN/MAX level is visible
inside of the tank.
WARNING
The appliance is not equipped with a device to melt fat. When using fat for
the first time, melt it beforehand
in a separate saucepan.
The next time you use the fryer, proceed as follows:
Make a few holes in the solidified fat down to the level of the heating
elements. Turn the thermostat knob to a
maximum of 100°C. Heat for one minute, then turn the knob back to 0. Repeat
this operation until the fat has
become liquid.
5 Use of the fryer
5.1 Control panel
Use of the control panel
To turn the appliance on, rotate the temperature control clockwise so that the
green neon illuminates.
To select the required frying temperature, continue to turn the knob in a
clockwise direction. Tthe amber neon will illuminate to show that the heating
elements are working. Once the set temperature is reached, the amber neon will
extinguish.
Turning off the appliance
Turn the temperature control to the “0” position;
6.1 Cleaning and maintenance
6.2 Cleaning intervals
NOTE
Only use non-caustic, non-abrasive cleaner.
Only use non-abrasive cleaning cloths.
Only use cleaners which are permitted in the food area.
Always carry out cleaning work only after the oil and the appliance have
cooled down to a temperature level at
which no scalding can occur.
6.1 Frying oil change
6.2 Periodic checks
6.3 Maintenance
We recommend a regular maintenance service by an after sales service company,
according to the intensity of use
of the equipment.
7. After sales service
In the case of a breakdown, contact your local dealer or the nearest repair centre. However, firstly check:
- that the fuses have not gone
- if the electric plug is pushed right in
- if the appliance has been started correctly
- if the oil level is correct
Important
If you call the repair centre, give the type and number of your appliance. You
will find these on the small plate on
the panel behind the door.
S11 Main Control
S21 Switch sécurité Safety
K11
Contactor
K21 Contactor
F11 Safety thermostat
F21 Control thermostat
R1-3 Heating elements
H12 Amber neon
Electrical Diagram
S11 Main Control
S21 switch Interruttore di
K11 Contactor
K21 Contactor
F11 Safety thermostat
Control thermostat
R1-3 Heating elements
H12 Amber neon
Electrical Diagram
S11 Main Control
S21 switch Interruttore di
K11 Contactor
K21 Contactor
F11 Safety thermostat
F21 Control thermostat
R1-3 Heating elements
H12 Amber neon
Electrical Diagram
Cooking Systems with Oil
LINCAT LTD
Whisby Road, Lincoln. United Kingdom
Tel. +44 (0) 1522 875555
www.lincat.co.uk
USE OF SOLID FATS
This unit is designed to be used with oils and fats in a liquid form.
Oils and fats that become solid at lower temperatures must be liquefied prior
to dispensing into the fryer tank.
This instruction applies to both filling from empty and topping up during use.
On units with filtration the oil or fat used must also be liquid prior to
operating the pump.
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>