Studebaker SB3706 Personal Bluetooth CD/MP3 Player Owner’s Manual
- September 19, 2024
- Studebaker
Table of Contents
- SB3706 Personal Bluetooth CD/MP3 Player
- Specifications:
- Product Usage Instructions:
- Compliance with FCC Regulations:
- On Protection Against Laser Energy Exposure:
- Power Source:
- Q: How can I charge the device?
- Q: What should I do if interference occurs during
- Q: How do I protect against laser energy exposure?
SB3706 Personal Bluetooth CD/MP3 Player
“`html
Specifications:
- FCC ID: 2A38HSB3706
- Model Number: SB3706
- Power Source: Built-in Lithium Battery
- Charging Input: DC 5V 1A USB charger or AC adaptor with DC 5V,
1000mA output
Product Usage Instructions:
Compliance with FCC Regulations:
This device complies with Part 15 of the FCC Rules. To ensure
proper operation, follow these guidelines:
-
Avoid causing harmful interference.
-
Accept any interference received.
-
Take necessary steps if interference occurs:
-
Reorient or relocate the receiving antenna.
-
Increase separation between equipment and receiver.
-
Connect equipment to a different circuit than the
receiver. -
Consult a professional for assistance if needed.
-
On Protection Against Laser Energy Exposure:
Follow these precautions for safe operation:
-
Avoid disassembling the casing due to the harmful laser
beam. -
Stop operation if any foreign objects enter the cabinet.
-
Avoid touching or poking the lens to prevent damage.
-
Avoid placing objects in the safety slot to prevent laser diode
activation. -
Disconnect all power sources and remove batteries if not in use
for an extended period.
Power Source:
The unit operates on a built-in Li-ion battery. Charge using a
DC 5V 1A USB charger or a compatible AC adaptor with DC 5V, 1000mA
output. Charge for at least 5 hours before initial use, even if the
charging LED turns off.
FAQ:
Q: How can I charge the device?
A: You can charge the device using a DC 5V 1A USB charger (not
included) or an AC adaptor (not included) with a rated output of DC
5V, 1000mA. Ensure to charge for at least 5 hours before first
use.
Q: What should I do if interference occurs during
operation?
A: If interference is experienced, try reorienting or relocating
the antenna, increasing separation between equipment and receiver,
connecting to a different circuit, or seek assistance from a
professional technician if needed.
Q: How do I protect against laser energy exposure?
A: Avoid disassembling the casing, touching the lens, placing
objects in the safety slot, or leaving the unit unused for an
extended period without disconnecting power sources and removing
batteries.
“`
COMPLIANCE WITH FCC REGULATIONS
FCC ID: 2A38HSB3706
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may
cause undesired operation. This equipment has been tested and found to comply
with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna. – Increase the separation
between the equipment and receiver. – Connect the equipment into an outlet on
a circuit different from that to which the receiver is
connected. – Consult the dealer or an experienced radio/TV technician for
help.
WARNING Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to operate
the equipment.
CAUTION
Follow the advice below for safe operations. ON PROTECTION AGAINST LASER
ENERGY EXPOSURE As the laser beam used in this compact disc player is harmful
to the eyes, do not attempt to
disassemble the casing. Stop operation immediately if any liquid or solid
object should fall into the cabinet. Do not touch the lens or poke at it. If
you do, you may damage the lens and the player may
not operate properly. Do not put anything in the safety slot. If you do, the
laser diode will be ON when the CD door
E-1
is still open. If the unit is not to be used for a long period of time, make
sure that all power sources are
disconnected from the unit. Remove all batteries from the battery compartment.
This unit employs a laser. The use of controls or adjustment or performance of
procedures
other than those specified here may result in exposure to hazardous radiation.
Should any trouble occur, remove the power source and refer servicing to
qualified personnel.
PROTECT YOUR FURNITURE
This system is equipped with non-skid rubber feet’ to prevent the product from moving when you operate the controls. These
feet’ are made from non-
migrating rubber material specially formulated to avoid leaving any marks or
stains on your furniture. However certain types of oil based furniture
polishes, wood preservatives, or cleaning sprays may cause the rubber feet’ to soften, and leave marks or a rubber residue on the furniture. To prevent any damage to your furniture we strongly recommend that you purchase small self-adhesive felt pads, available at hardware stores and home improvement centers everywhere and apply these pads to the bottom of the rubber
feet’
before you place the product on fine wooden furniture.
E-2
DEAR STUDEBAKER ® CUSTOMER
Selecting fine audio equipment such as the unit you’ve just purchased is only
the start of your musical enjoyment. Now it’s time to consider how you can
maximize the fun and excitement your equipment offers. This manufacturer and
the Electronic Industries Association’s Consumer Electronics Group want you to
get the most out of your equipment by playing it at a safe level. One that
lets the sound come through loud and clear without annoying blaring or
distortion and, most importantly, without affecting your sensitive hearing.
Sound can be deceiving. Over time your hearing “comfort level” adapts to
higher volumes of sound. So what sounds “normal” can actually be loud and
harmful to your hearing. Guard against this by setting your equipment at a
safe level BEFORE your hearing adapts.
To establish a safe level: · Start your volume control at a low setting. ·
Slowly increase the sound until you can hear it comfortably and clearly, and
without distortion. · Once you have established a comfortable sound level: Set
the dial and leave it there. Taking a minute to do this now will help to
prevent hearing damage or loss in the future. After all, we want you listening
for a lifetime.
We Want You Listening For a Lifetime Used wisely, your new sound equipment
will provide a lifetime of fun and enjoyment. Since hearing damage from loud
noise is often undetectable until it is too late, this manufacturer and the
Electronic Industries Association’s Consumer Electronics Group recommend you
avoid prolonged exposure to excessive noise.
Customer’s Record: The serial number of this product is found on its back
cover. You should note the serial number of this unit in the space provided as
a permanent record of your purchase to aid in identification in the event of
theft of loss.
Model Number: SB3706
Serial Number:
E-3
LOCATION OF CONTROLS
1 LCD DISPLAY
12 PROGRAM BUTTON
2 MODE BUTTON
13 A-B BUTTON
3 BATTERY CHARGING INDICATOR 14 PRESET+ / FOLDER+ BUTTON
4 BLUETOOTH/FM TX BUTTON
15 HEADPHONE JACK
5
/ TUNER- BUTTON
16 EQ/BBS ON/OFF BUTTON
6 REPEAT BUTTON
17 VOLUME + BUTTON
7 FM SCAN BUTTON
18 VOLUME – BUTTON
8 PRESET- / FOLDER- BUTTON
19. CD DOOR OPEN SWITCH
9. POWER ON / CD BUTTON
20. USB-C JACK
10. POWER OFF / CD BUTTON
21 HOLD SWITCH
11
/ TUNER + BUTTON
E-4
POWER SOURCE
Built-in Lithium Battery This unit operates on a built-in Li-ion battery that
can be recharged either by using DC 5V 1A USB charger (not included) or from
an AC adaptor (not included) with a rated output of DC 5V, 1000mA. The
internal battery may not be fully charged out of the box, even if the RED
charging LED turns off. We recommend that you charge the SB3706 for at least 5
hours before first use.
Note: The Type-C USB and DC IN jack are located on the righthand side of the
unit. They are designed for charging the internal Li-ion battery. The unit
will still operate while charging, but doing this may reduce the battery life
and increase the charging time.
LOW BATTERY INDICATOR When using battery power to operate this unit and the
battery power becomes weak, the “BATTERY LOW” will show on display for few
seconds and repeat. You are recommended to charge the rechargeable battery.
Note: 1. After prolonged use, the battery voltage will discharge, and
operation might become intermittent. When this happens, please recharge the
internal battery. 2. Charging time will vary if you are listening to music
while charging the unit battery. We recommend you turn off the unit power
during the charging process or until the unit battery is fully charged. 3. To
prolong the life of a rechargeable battery, it is recommended to completely
discharge it before fully charging it again. 4. Rechargeable batteries need to
be cycled for maximum performance and longer battery life. If you don’t use
the player that often, be sure to recharge the battery at least once a month
in order to keep the internal battery working properly.
BATTERY NOTE AND CARE
Do not burn or bury batteries. Do not puncture or crush. Do not disassemble.
Recycle Li-ion batteries. Do not dispose of in the trash. Use only chargers
rated for Li-ion cells. Be sure the charger’s voltage and current
settings are correct for the battery pack being charged. Charge batteries on a
fireproof surface away from flammable items or liquids. Batteries should NEVER
be left unattended while charging. Only adults should charge
the batteries. Follow the manufacturer’s instructions for charging the product
and do not charge longer
than recommended. Unplug the charger when the battery is charged or not in
use.
CHARGING THE BATTERY USING THE TYPE C USB PORT 1. Charge the built-in Lithium
battery a minimum of 5 hours prior to first use. 2. Use the included charging
cord and plug the SB3706 into a USB power adaptor (not
included). 3. The BATTERY CHARGING INDICATOR (#3) will light solid Red showing
that the internal
battery is being charged. 4. After the battery is fully charged, the BATTERY
CHARGING INDICATOR (#3) will turn off. 5. Unplug the USB to Type-C cable from
the power source once the battery is fully charged.
E-5
NOTE 1. You can use an USB AC adaptor with an output current of 500 mA or
computer USB port as well, but it may take a very long time (10 hours or more)
before the SB3706 has a full charge. When using such a USB AC adaptor, it’s
recommended that you turn off the SB3706 power before charging the battery. 2.
Use of a USB AC adaptor with an output current of less than 500 mA is not
guaranteed to charge the unit’s battery.
CHARGING THE BATTERY USING THE AC Adaptor (Not included) Use an AC adaptor
with output DC 5V 1000mA. 1. Plug the AC adaptor (not included) into normal AC
power outlet socket. 2. Insert the DC plug of the AC adaptor cord into the DC
IN JACK. 3. The BATTERY CHARGING INDICATOR (#3) will light solid Red showing
that the internal
battery is being charged. 4. After the battery is fully charged, the BATTERY
CHARGING INDICATOR (#3) will turn
off. 5. Unplug the AC adaptor once the battery is fully charged. WARNING:
Before connecting to the power supply, ensure that the supply corresponds to
the information on the rating label at the back of the apparatus. AC/DC
Adaptor
EARPHONES CONNECTION (PLUG-IN TYPE)
Connect the plug of the stereo earphone (included) into the EARPHONES JACK
(#15). CAUTION · Avoid excessive volume levels for long period of time when
using the earphones.
Prolonged use at high levels may impair your hearing. · Do not use earphones
while operating a motorized vehicle, as it may create a traffic
hazard and is illegal in many areas.
E-6
CD/MP3 CD OPERATION
PLEASE READ THIS IMPORTANT INFORMATION: CD mechanisms used in devices like
this are designed to fully read all commercial CDs. They will also read self-
compiled CD-R/CD-RW discs, however it may take up to 10 seconds for playback
to start. If playback does not start, it is likely due to the quality of the
CD-R/RW disc and/or the compatibility of the CD compilation software. The
manufacturer is not responsible for the playback quality of CD-R/RW discs. Do
not attach a label or seal to either side of the CD-R/RW disc as this may
cause a malfunction.
FOR WINDOWS USERS: When using the “Burn a CD” feature to create an MP3 CD in
Windows, you must select the “With a CD/DVD player” option when it asks, “How
do you want to use the disc?”. The MP3 CD will not play on this unit if you
select the “Like a USB flash drive” option or if the MP3 CD is not finalized.
PLAYING A COMMERCIAL CD 1. Make sure the HOLD SWITCH (#21) located on the
bottom of the unit is set to OFF
position. Press the POWER ON BUTTON (#9) to turn on the unit. 2. Press the
MODE BUTTON (#2) to enter CD mode if necessary. 3. Slide the CD DOOR OPEN
SWITCH (#19) to open the CD door. Carefully place an audio
CD with its label side upward in the CD compartment and close the CD door. 4.
The player will start reading TOC of the disc and LCD DISPLAY (#1) showing
“READ”
during CD loading. 5. The total number of tracks and time on the CD will show
on the LCD DISPLAY (#1) after a
few seconds. 6. Press the BUTTON (#9) to start to play the CD. 7. Press the
VOLUME +/- BUTTONS (#17/18) to obtain the desired volume level. 8. While
playing, press the BUTTON (#9) to pause playback. The current track number
will be flashing on the LCD DISPLAY (#1). Press the BUTTON (#9) again to
resume playing. 9. You can choose to play your favorite track directly by
pressing either the or BUTTONS (#5 or #11) repeatedly. The LCD Display (#1)
will indicate the correct track number selected. 10. To locate a particular
passage within a track, press and hold the or buttons (#5 or #11) until it is
found.
Note: Low level audio will be heard during the search process to assist in
locating the desired point of the track.
11. To stop playing, press the STOP BUTTON (#10). 12. Press and hold the
POWER OFF BUTTON (# 10) to turn off the unit.
REPEAT MODE PLAYING A COMMERCIAL CD
REPEAT 1: When you first start playing a CD, press the REPEAT BUTTON (#6) once
and “REP 1” will show on the LCD DISPLAY (#1). The current track that is
playing will now repeat continuously
E-7
until you stop playback or change the mode.
REPEAT ALL: Press the REPEAT BUTTON (#6) again and “REP ALL” will show on the
LCD DISPLAY (#1). All tracks on the CD will play in order and will repeat
continuously until you stop playback or change the mode.
RANDOM PLAY: Press the REPEAT BUTTON (#6) again and “RND” will show on the LCD
DISPLAY (#1). All tracks on the CD will play in random order until you stop
playback or change the mode.
INTRODUCTION PLAY: Press the REPEAT BUTTON (#6) again and “INTRO” will show on
the LCD DISPLAY (#1). All tracks on the CD will play the first 10 seconds in
order until you stop playback or change the mode.
CANCELLING THE REPEAT MODES: Press the REPEAT BUTTON (#6) again or until all
the symbols on the LCD DISPLAY (#1) turn off.
PLAYING A MP3 CD 1. Make sure the HOLD SWITCH (#21) located on the bottom of
the unit is set to OFF
position. Press the POWER ON BUTTON (#9) to turn on the unit. 2. Press the
MODE BUTTON (#2) to enter CD mode if necessary. 3. Slide the CD DOOR OPEN
SWITCH (#19) to open the CD door. Carefully place an MP3
CD with its label side upward in the CD compartment and close the CD door. 4.
The CD will spin and start reading the disc information. When finished, the
LCD
DISPLAY (#1) will show the total number of folders followed by the total
number of tracks on the MP3 CD. 5. Press the BUTTON (#9) to start playing the
MP3 CD. 6. Press the VOLUME +/- BUTTONS (#17/#18) to obtain the desired volume
level. 7. While playing, press the BUTTON (#9) to pause playback. The current
track number will be flashing on the LCD DISPLAY (#1). Press the BUTTON (#9)
again to resume playing. 8. Pressing the FOLDER / BUTTONS (#8/#14) allows you
to switch folders (if available on your MP3 CD). Repeatedly press the FOLDER /
BUTTON (#8/#14) to step through all the available folders on the MP3 CD. The
LCD DISPLAY (#1) will show F01 is folder #1, F02 is folder #2 and so on. 9.
You can choose to play your favorite track directly by pressing either the or
BUTTONS (#5 or #11) repeatedly. The LCD Display (#1) will indicate the correct
track number selected. 10. To locate a particular passage within a track,
press and hold the or BUTTONS (#5 or #11) until it is found. Note: Low level
audio will be heard during the search process to assist in locating the
desired point in the track. 11. To stop playing, press the STOP BUTTON (#10).
12. Press and hold the POWER OFF BUTTON (#10) to turn off the unit.
E-8
REPEAT MODE PLAYING AN MP3 CD
REPEAT 1: When you first start playing an MP3 CD, press the REPEAT BUTTON (#6)
once and “REP 1” will show on the LCD DISPLAY (#1). The current track that is
playing will now repeat continuously until you stop playback or change the
mode.
REPEAT FOLDER (ALBUM): Press the REPEAT BUTTON (#6) again and “REP
DIR(FOLDER)” appears on the LCD DISPLAY (#1). Repeatedly press the FOLDER /
BUTTONS (#8/#14) to step through all the available folders and select the
folder you want to reply. All tracks in that folder will play in order and
will repeat continuously until you stop playback or change the mode.
REPEAT ALL: Press the REPEAT BUTTON (#6) again and “REP ALL” will show on the
LCD DISPLAY (#1). All tracks on the MP3 CD will play in order and will repeat
continuously until you stop playback or change the mode.
RANDOM PLAY: Press the REPEAT BUTTON (#6) again and “RND” will show on the LCD
DISPLAY (#1). All tracks on the MP3 CD will play in random order until you
stop playback or change the mode.
INTRODUCTION PLAY: Press the REPEAT BUTTON (#6) again and “INTRO” will show on
the LCD DISPLAY (#1). All tracks on the MP3 CD will play the first 10 seconds
in order until you stop playback or change the mode.
CANCELLING THE REPEAT MODES: Press the REPEAT BUTTON (#6) again or until all
the symbols on the LCD DISPLAY (#1) turn off.
NOTE: The unit will automatically go into power saver mode and turn off if the
CD player is stopped for longer than 2 minutes.
PROGRAM PLAY MODE (COMMERCIAL CD and MP3 CD) This function allows the tracks
to be played in a programmed sequence. Programs can be set in STOP mode. 1.
Press the PROGRAM BUTTON (#12) once. The track number “001” and Program
Channel Number “P01” will appear on display. “001” of the track number will
blink on the LCD DISPLAY (#1) to prompt for input. 2. Press the or BUTTONS
repeatedly (#5 or #11) to select the track to be programmed. Note: Press the
FOLDER+/- BUTTON (#8/14) button to select the next/previous MP3 folder if you
are programming tracks of an MP3 CD. Press the FOLDER+/- BUTTON (#8/14) button
repeatedly to cycle the folder selection. 3. Press the PROGRAM BUTTON (#12)
again to store selection. The Program Channel Number will change to “P02” and
the track number will continue to blink, prompting for input the next track to
be programmed.
E-9
4. You may repeat steps #2 – #3 to program up to 24 tracks for CD or 99
tracks for MP3 CD. 5. Press PLAY/PAUSE BUTTON (#9) to start the programmed
play, “PROG” icon appears
on the LCD DISPLAY (#1). 6. You may repeat the current programmed track or all
programmed tracks by pressing the
REPEAT BUTTON (#2) once or twice at programmed play mode. 7. Press STOP BUTTON
(#10) once to stop playback. 8. Press PLAY/PAUSE BUTTON (#9) to resume
programmed play. 9. To cancel programmed play, press the STOP BUTTON (#10)
twice.
A_B REPEAT PLAYBACK
1. During CD or MP3 CD playback, press A-B BUTTON (#13) at the desired point
where you would like to set the starting time of A-B playback. “SET A” is
displayed on the LCD display (#1) and will show the track time after 3
seconds.
2. Press REPEAT A-B BUTTON (#13) at the point where you want to set the end
time of the A-B playback. “Ab ON” is displayed on the LCD DIAPLAY (#1) will
show the track time after 3 seconds. “A-B” will display on the LCD DISPLAY
(#1) and selected period (point A to point B) will playback repeatedly.
3. Press the STOP BUTTON (#10) to clear the A-B repeat playback setting and
stop playback. Or press A-B BUTTON (#13) to cancel the A-B repeat and carry on
the playback.
AUTOMATIC RESUME FUNCTION
If the CD Player turns off during playback due to power failure or the CD door
accidentally being opened, you can resume playback from the same position
after restarting the unit or closing the CD door again. Auto resume also works
if you turn the CD Player off and want to continue listening at a later time.
ANTI-SHOCK PROTECTION
This player incorporates an electronic anti-skip circuit to prevent
interruption of the sound output when the unit is subjecting to shock,
vibration or rolling during CD playback. The antisshock system will
automatically activate when a disc is playing, the ESP indicator will appear
on the LCD DISPLAY (#1). Once the anti-skip buffer is full, it will give you
approximately 60 seconds of protection against interruption of sound output.
If the player is subjected to shock or rolling for longer than the buffer
memory, some interruption of sound output will occur. This is normal and to be
expected. Afterwards, the sound will resume once the player has stabilized
from the shock or rolling disturbance. Note: The anti-skip function provides
for continuous playback when the unit is subjected to
shock or vibration. It will not compensate for errors arising from the use of
defective, scratched or dirty discs.
E-10
RADIO OPERATION
1. Press and hold the POWER ON BUTTON (#9) to turn on the unit. 2. Press the
MODE BUTTON (#2) to enter FM mode if the unit is in CD mode. “FM” will
appear on the LCD DISPLAY (#1) along with the current FM radio station
frequency. 3. To automatically scan and store radio stations, press and hold
the SCAN BUTTON (#7)
until frequency readout on the display begins to scan and then release the
button. 4. To manually tune to a specific radio station, press the TUNER- or
TUNER+ BUTTON (#5
or #11) repeatedly. Use the manual tuning method to tune in weaker stations
that are bypassed during Automatic Tuning. 5. To automatically tune to the
next available radio station, press and hold the TUNER- or TUNER+ BUTTON (#5
or #11) for 1-2 seconds until frequency readout on the display begins to scan
and then release the button. The tuner will stop scanning when it receives the
next broadcasting station of adequate signal strength. 6. Press the volume
control VOLUME +/ BUTTON (#17/#18) to the desired volume level.
FM OPERATION During FM reception, always keep the earbuds wire fully extended
for best performance. However, if FM reception is weak, try repositioning the
unit near an open window until you get the best reception.
TIPS FOR BEST RECEPTION The earbuds cord acts as an aerial and must be fully
extended for the best reception.
PRESET RADIO STATIONS 1. Press the POWER ON BUTTON (#9) to turn on the unit.
2. Press the MODE BUTTON (#2) to enter FM mode when the unit is at CD mode,
the FM
radio frequency will appear on the LCD DISPLAY (#1). 3. Tune to the desired
radio station utilizing either “manual” or “automatic” tuning methods. 4.
Press the PROGRAM BUTTON (#12), the preset memory number will flash on the LCD
DISPLAY (#1). (Note: P01 will blink in the display if you are programming a
preset for the first time). 5. Press the PRESET+/- BUTTON (#8/14) repeatedly
to select the preset number you want to assign the station to. 6. Press the
PROGRAM BUTTON (#12) to confirm the setting. 7. Repeat above steps #3 – #6 to
preset up to 30 FM stations.
NOTE: This unit features an AUTO SEARCH function that will automatically save
the first 30 strong stations found. To use this feature, make sure the unit is
in FM mode. Press and hold the SCAN BUTTON (#7) until the station frequency
begins to scan. The unit will scan from the lowest frequency to the highest
frequency within the frequency band. The first strong radio stations found
will be stored in the preset locations starting from P01. This will continue
storing P02 and up until all 30 presets are stored, or until it runs out of
stations to scan.
RECALLING PRESET RADIO STATIONS Press the PRESET+/- BUTTON (#8/#14) repeatedly
to select the desired station is located.
E-11
BLUETOOTH TRANSMIT MODE
The SB3706 has a built-in Bluetooth transmitter that allows you to wirelessly
stream to Bluetooth compatible devices like speakers, headphones or earbuds.
Follow the steps below to connect to a Bluetooth device and stream your
favorite CDs to that device. PAIRING WITH A BLUETOOTH DEVICE (SPEAKERS,
HEADPHONES OR EAR BUDS) 1. Press and hold the MODE BUTTON (#2) to enter CD
mode (CD stopped). 2. Make sure the Bluetooth device you want to stream to is
ON and set to pairing mode.
NOTE: For best results, have the Bluetooth device as close as possible or
within 3 feet of the SB3706 when pairing.
3. Press the BLUETOOTH/FM TX BUTTON (#4) once to switch to Bluetooth Search
Mode. “BT TX” shows on the LCD Display (#1) (Fig 1).
4. The SB3706 will search for the closest available Bluetooth device and
automatically connect to that device.
5. Once Bluetooth pairing is successful, the display will change back to the
CD screen and “BT TX” will be showing in the upper right the LCD Display (#1)
(Fig 2). This confirms the unit is transmitting Bluetooth.
NOTE: Please note that the pairing time could be longer when connecting with a
device for the first time.
6. Press the PLAY/PAUSE BUTTON (#9) to start playing the CD and begin
streaming (Fig 3). The music from the CD will be heard on the connected
Bluetooth device.
7. If you move out of Bluetooth range (33 feet) with the SB3706, the “BT TX”
indicator on the LCD Display (#1) will begin flashing. Move the SB3706 or your
Bluetooth device back within range and reconnect the Bluetooth device if
necessary.
8. If you want to connect to another Bluetooth device, first turn OFF the
power on the current device you are connected to.
Fig. 1 Fig. 2
Fig. 3
9. Make sure the new Bluetooth device to you want to connect to is ON, set to pairing mode and placed near the SB3706
10. Repeat Follow steps #3 #7 to connect to the new Bluetooth device.
Notes: · Bluetooth streaming is not available in FM radio mode. · If Bluetooth
speaker or headphone has been connected before turning off, it will
E-12
automatically connect back to the previous one during next connection.
· If the CD player is stopped for approximately 120 seconds, the power will
automatically turn off, so you may need to repeat the Bluetooth connection
steps above to stream again.
· If you need to remove a previously connected device from the SB3706 press
and hold the A-B BUTTON (# 12) to disconnect it. Immediately turn off the
Bluetooth device to prevent the SB3706 from reconnecting to it.
· This model is compatible with Bluetooth versions 4.0 & 5.0. Please try your
other Bluetooth speaker or headphone if it is unable to find by this model.
· This CD player may not connect to certain vehicle entertainment systems if
the manufacturer requires a passcode during the connection process.
TURNING OFF BLUETOOTH TRANSMISSION 1. Press the BLUETOOTH/FM TX BUTTON (#4)
repeatedly until
“OFF” appears on the LCD Display (#1) as shown in Fig 4.
2. The Bluetooth transmitter is now off and no longer connected to any
device.
Fig. 5
Fig. 4
FM TRANSMIT MODE
1. Press the MODE BUTTON (#2) to enter CD mode (while CD stopped).
2. Press the BLUETOOTH/FM TX BUTTON (#4) once to
switch to Bluetooth Search Mode. “BT TX” shows on the
LCD Display (#1) (Fig 1).
3. Press the BLUETOOTH/FM TX BUTTON (#4) again to
switch to FM transmit mode, LCD DISPLAY (#1) will
change to show ” ” and one of the FM TX frequencies.
e.g. 88.5MHz (Fig. 5).
4. Press the or BUTTON (#5 or #11) repeatedly to
Fig. 1
select 1 of the 3 FM transmit frequencies available. 88.5MHz = 93.7MHz = 102.9MHz.
5. Tune the FM radio in your car to the same FM transmit
frequency selected above.
6. Press the Play button on the SB3706 to start playing the CD.
The music from the CD will be heard on the radio in your
car.
7. If the music from the CD is not playing through your car radio, please repeat steps 1-5 above and select another FM
Fig. 5
transmit frequency. Make sure you readjust the FM radio station in your car
E-13
to the new frequency selected. 8. Adjust volume of the CD player and your car
radio if
necessary. 9. Turn off CD player after listening.
Notes:
· FM transmit is not available while the SB3706 is in FM radio mode.
Fig. 6
· Bluetooth transmit and FM transmit will not run at the same time.
· If you’re experiencing static or interference when listening to a CD on your car radio, reposition where the SB3706 is located and position it closer to the radio if possible.
BBS FUNCTION
1. Press and hold the BBS BUTTON (#16) to turn on the BBS to enhance the bass
effect of the music. Display will show “BBS ON” once.
2. Press and hold the button again to turn off the BBS. Display will show
“BBS OFF” once again.
Note: EQ will be reset to “FLAT” if you turn BBS ON/OFF.
EQ MODES
This unit provides 4 different EQ modes to enhance your listening experience.
You can select the desired effect by press the BBS BUTTON (#16) repeatedly in
following sequence:
FLAT CLASSIC ROCK POPS JAZZ Note: BBS will be off if you select EQ mode.
HOLD FUNCTION
To prevent accidental function changes during active use, this unit is fitted
with a function hold. After the unit has been powered on and playing in CD or
FM mode, slide the HOLD SWITCH (#21) to ON position. “HOLD” message will show
on the LCD DISPLAY (#1). LCD DISPLAY (#1) will off for 2 seconds when you
press a key. Set the HOLD SWITCH (#21) to OFF position to unlock the hold
function.
Note: Auto power off for saving battery power will not be affected by hold
function.
RESETTING THE UNIT
In case of malfunction due to electrostatic discharge, reset the unit by
pressing and holding the POWER OFF BUTTON (#10) until the unit turns off.
Waiting for 30 seconds and then press POWER ON BUTTON (#9) to turn on the unit
again.
E-14
CARE AND MAINTENANCE
1. Clean your unit with a damp (never wet) cloth. Solvent or detergent should
never be used. 2. Avoid leaving your unit in direct sunlight or in hot, humid
or dusty places. 3. Keep your unit away from heating appliances and sources of
electrical noise such as fluorescent lamps or motors. 4. If drop-outs or
interruptions occur in the music during CD play, or if
the CD fails to play at all, its bottom surface may require cleaning. Before
playing, wipe the disc from the center outwards with a good soft cleaning
cloth.
TROUBLE SHOOTING GUIDE
If you experience difficulties in the use of this clock radio, please check
the following or call 1-800-777-5331
for Customer Service and support
SYMPTOM No Sound Noise or sound distorted on FM broadcast Radio no sound
CD player will not play
CD skips while playing
POSSIBLE Battery no power Volume set at minimum
SOLUTION Fully recharge the built-in rechargeable battery. Increase Volume.
Earphone cord is not extended
Extend earphone cord
The unit is not in RADIO (FM) mode
Switch to FM mode
The station is weak
Retune the station again
Unit not in CD mode
Switch to CD mode
CD is installed incorrectly
Insert CD with label side up.
Battery becomes exhausted It the CD is self-compiled, the media used may not
be compatible with the player. Disc is dirty or scratched. Dirty or defective
disc
Dirty pick up lens
Player is subject to excessive shock or vibration
Fully recharge the built-in rechargeable battery.
Use better quality blank media and retest.
Wipe CD with clean cloth or use another disc. Clean or replace the defective
disc Use a CD-lens cleaning disc to clean the lens Relocate the player away
from shock or vibration
E-15
CD skips while playing
Cannot pair with Bluetooth speaker
Battery becomes exhausted
The unit is not in Bluetooth (TX) mode No power is turned on is Bluetooth
speaker or headphone
Fully recharge the built-in rechargeable battery. Switch to Bluetooth (TX)
mode
Turn Power on the Bluetooth speaker or headphone
SPECIFICATION
Power Requirement
: 5V DC (1.0A) Type-C USB (cable supplied)
: Built-in lithium-ion rechargeable battery (3.7V/1500mAh)
: AC Adaptor (not included): Input: AC 120V ~ 60Hz
: Output: DC 5V 1000mA
FM Receiver Frequency : 87.5 108 MHz
FM Transmitter Frequency : 88.5MHz, 93.7Mhz, 102.9MHz
Bluetooth
: Version 5.0
At Spectra, environmental and social responsibility is a core value of our
business. We are dedicated to continuous implementation of responsible
initiatives with an aim to conserve and maintain the environment through
responsible recycling.
Please visit us at http://www.spectraintl.com/green.htm for more information
on Spectra’s green initiatives or to find a recycler in your area.
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by Spectra Merchandising Intl,
Inc. is under license. Other trademarks and trade names are those of their
respective owners.
E-16
1 YEAR LIMITED WARRANTY AND SERVICE VALID IN THE U.S.A. ONLY
SPECTRA MERCHANDISING INTERNATIONAL, INC. warrants this unit to be free from
defective materials or factory workmanship for a period of 1 year from the
date of original customer purchase and provided the product is utilized within
the U.S.A. This warranty is not assignable or transferable. Our obligation
under this warranty is the repair or replacement of the defective unit or any
part thereof, except batteries, when it is returned to the SPECTRA Service
Department, accompanied by proof of the date of original consumer purchase,
such as a duplicate copy of a sales receipt. You must pay all shipping charges
required to ship the product to SPECTRA for warranty service. If the product
is repaired or replaced under warranty, the return charges will be at
SPECTRA’s expense. There are no other express warranties other than those
stated herein. This warranty is valid only in accordance with the conditions
set forth below: 1. The warranty applies to the SPECTRA product only while:
a. It remains in the possession of the original purchaser and proof of
purchase is demonstrated. b. It has not been subjected to accident, misuse,
abuse, improper service, usage outside the
descriptions and warnings covered within the user manual or non-SPECTRA
approved modifications. c. Claims are made within the warranty period. 2. This
warranty does not cover damage or equipment failure caused by electrical
wiring not in compliance with electrical codes or SPECTRA user manual
specifications, or failure to provide reasonable care and necessary
maintenance as outlined in the user manual. 3. Warranty of all SPECTRA
products applies to residential use only and is void when products are used in
nonresidential environment or installed outside the United States.
This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state. TO OBTAIN SERVICE please remove all
batteries (if any) and pack the unit carefully and send it freight prepaid to
SPECTRA at the address shown below. IF THE UNIT IS RETURNED WITHIN THE
WARRANTY PERIOD shown above, please include a proof of purchase (dated cash
register receipt) so that we may establish your eligibility for warranty
service and repair of the unit without cost. Also include a note with a
description explaining how the unit is defective. A customer service
representative may need to contact you regarding the status of your repair, so
please include your name, address, phone number and email address to expedite
the process.
IF THE UNIT IS OUTSIDE THE WARRANTY PERIOD, please include a check for $49.99
to cover the cost of repair, handling and return postage. All out of warranty
returns must be sent prepaid.
It is recommended that you contact SPECTRA first at
1-800-777-5331 or by email at
custserv@spectraintl.com for updated information on the unit requiring
service. In some cases, the model you have may be discontinued, and SPECTRA
reserves the right to offer alternative options for repair or replacement.
SPECTRA MERCHANDISING INTERNATIONAL, INC. 4230 North Normandy Avenue, Chicago,
IL60634, USA. 1-800-777-5331
To register your product, visit the link on the website below to enter your
information. http://www.spectraintl.com/wform.htm
0724
Printed in China (SB3706MW/SB3706BP/SB3706BW/SB3706RW)
E-17
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>