ZEALOT P1 Wireless Speaker User Guide

September 18, 2024
ZEALOT

P1 Wireless Speaker
ZEALOT-P1ZEALOT P1 Wireless Speaker

Specification

Charging voltage: DC5V
Transmission distance: about 10m
Frequency response: 20Hz-20KHz
Signal to noise ratio: ≥85dB
Size: 321129166mm
Speaker: 4Ω x2
Distortion: <1%
Working voltage: 3.7V
Weight: 1336g

Power ON/OFF

Power on/off: long press for 3 seconds

Mode switching

Short press the “M° key to switch the mode.
(TF card, AUX mode is the priority for rear access.)

Rainbow light effect

Long press to play and pause to turn on and off the lights

Bluetooth Mode

Biuetooth connection:

Press and hold the key for 3 seconds to turn on and off the machine, the prompt sound “BULETOOTH MODE”, enter the Bluetooth pairing mode, Waiting for connection. Use a Bluetooth device (mobile phone) to automatically search for the device name “ZEALOT-P 1”, Click Connect and hear two beeps.
Indicates a successful connection.
How to reconnect?
When the speaker is turned on again, the Bluetooth will automatically connect to the paired mobile phone or other Bluetooth devices. If itis not connected, please enter the Bluetooth settings of the mobile phone to check whether the Bluetooth is turned on. The lOS system needs to turn on Bluetooth in advance to connect the speakers automatically. Otherwise, manually click on the ZEALOT-P1 connection.

Bluetooth playback

Single click- Play! Pause
Single click: Last
Long Press: Volume-
Single click: Next
Long Press: Volume+

TF, USB Mode

Insert the TF card or USB and listen to the prompt “Music Mode” to play the songs on the TF card.

Single click: Last
Long Press: Volume-
Single click: Next
Long Press: Volume

AUX Mode

Connect with audio cable, it will switch to aux mode after hearing the warning tone “ Line in Mode”.

FM mode

Single click: Automatic search channel
Single click: Last channel
Long Press: Volume-
Long Press: Next channel
Single click: Volume +

KTV Function

Plug in the wired karaoke microphone, karaoke in any mode,ZEALOT P1 Wireless
Speaker - ktv

Charger

  • Appearance of prompt voice “low battery Please Charge’,
  • The red indicator light is on when DC is charging, and the red charging indicator is off when fully charged
  • Different adapters, interfaces, and charging time will vary

Notice

  • Do not throw this product into fire or water.
  • Do not modify, repair or dissemble the speaker.
  • Do not make it contact with combustible materials directly.
  • Please keep the device away from damp and dusty environments.
  • Before charging please check whether the charger model is suitable for this product.
  • Do not use the Bluetooth function while charging.
  • The device will automatically lose power when it’s in standby,it’s recommended to charge the speaker once a month.

Please keep your speaker and mobile phone within 10m working range.
If over this distance, decline of sound quality and disconnection will occur.
ZEALOT P1 Wireless Speaker - Symbol 8 FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received. induding interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Ciass B digitat device, pursuant to part 15 of the FCC Rules. These fimits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuming the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • tnorease the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consuk the dealer or an experienced radio/TV technician for help.

Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. such modifications could void the user’s authority to operate the equipment.
The device has been evaluated to meet general RF exposure requirement.
This equipment complies with FCC’s RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna(s) must not be co- located or conjunction with any other antenna or transmitter.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals