SUNNY MCU HZ Type Emergency Light User Manual
- September 17, 2024
- Sunny
Table of Contents
MCU HZ Type Emergency Light
“`html
Specifications
-
Model: Self-Contained Emergency Light MCU Series
-
Types: MCU HZ Type, MCU NC Type
-
Control: LED AC, LED Charge/Full, LED Battery, LED Fail, LED 5
sec, LED 30 mins, LED 60 mins -
Features: Remote Testing, Dimmer, IR Receiver
Product Usage Instructions
Installation
-
The unit can be installed on leveled ground or hung up
securely. -
Ensure proper installation to prevent accidents or damage.
Operation
-
Press and hold the ON Switch for about 3 seconds to activate
the emergency lamps. -
To perform tests:
- Press the 30min button for a 30-minute test.
- Press the 60min button for a 60-minute test.
- To cancel the test, press the OFF button.
Important Notes
- Install indoors away from direct sunlight and moisture.
- Store in temperatures under 25°C.
- Charge the battery every 3 months for optimal performance.
FAQ
Initial Troubleshooting
| Cause | Problem | What to do |
|---|
Power not getting to the unit after plugging in. The LED AC
light does not turn on.| – Power socket might not have any power.
– Plug or socket is loose.
– AC fuse is blown.| – Check power supply.
– Check plug and socket.
– Contact customer service.
Emergency light does not turn on after power outage.| – Unit is not plugged
in.
– Lamp is faulty.
– Circuit’s wiring is loose.
– DC fuse is blown.| – Check if unit is plugged in.
– Contact customer service.
Emergency light only turns on for a short time after power
outage.| – Battery not fully charged.
– Battery degraded.| – Fully charge the battery.
– Contact customer service for battery replacement.
Terms for Warranty and Service
-
Fill in and mail the warranty registration form back to the
company within 7 days of purchase to activate warranty. -
Warranty covers internal parts as specified with durations
calculated from the date of purchase.
“`
USER MANUAL
Self-Contained Emergency Light MCU Series
MCU HZ Type MCU NC Type
LED AC LED Charge/Full LED Battery LED Fail LED 5 sec LED 30 mins LED 60 mins
Switch ON/OFF Switch Test IR Receiver
Dimmer
Indicate that the unit is receiving power. Gives information on battery charging. Indicate battery voltage range Indicate error status. Indicate the unit is performing a 5 second test. Indicate the unit is performing a 30-minute test. Indicate the unit is performing a 60-minute test. Press to turn ON/OFF the lamp. (while the unit is not plugged in) For testing the device’s availability. (during normal circumstance) Infrared signal sensor used to receive signal from the infrared remote. Press to adjust the brightness level (only supported in the HZ models).
Remote Testing
5 30 60 secs mins mins
Status Indicators and Testing Buttons
Remote Testing
Features
1. Controlled by a highly intelligent 8-bit micro controller. 2. Automatic
self-test system that is able to be set for every 1 or 6 months. The time,
date and duration of the automatic test can be set as desired. This will help
to extend the life of the battery as well as lower the burden of maintenance
on the user. 3. Testing can be activated remotely using the infrared remote.
4. The unit has a quick self-test function with durations of 5 seconds, 30
minutes and 60 minutes. 5. The brightness of the unit can be adjusted to 3
different levels for optimum brightness and operational time (only supported
for units with the HZ lamp type). 6. Using high quality LEDs with a lifetime
of over 50,000 hours, providing bright and constant illimitation throughout
its operation. 7. The unit’s outer case is made from ABS UL94 V-O Flame
Retardant plastic that is highly resistant to impact and corrosion.
Installation and Operation
1. The unit can be installed on leveled ground or hung up. 2. Install
properly and securely to prevent accidents that could cause damage to the
unit or other people and property. 3. Press and hold the ON Switch for about 3
seconds. Both emergency lamps will
illuminate and the LED ON light on the unit will turn on indicating that the
unit is operational. 4. Plug the unit into a power socket with a 220-240VAC
power supply. The emergency lamp will remain on for about 5 seconds before
turning off. 5. Press the Dimmer button to adjust the brightness of the unit
(only supported in the HZ models). 6. When the unit is operational, tests can
be performed using the Test button on the unit or remotely using the remote
with the following options. – Press the 5sec button to perform a 5 second
test, after which the unit will return to
normal operation. – Press the 30min button to perform a 30-minute test, after
which the unit will return
to normal operation. – Press the 60min button to perform a 60-minute test,
after which the unit will return
to normal operation. – To cancel the test, press the OFF button.
Note : When activating the self-test function whether through the remote or
the buttonon the unit the test button will have the same function.
Important Note on Using the Unit
1. The unit should be installed indoors away from direct sunlight and rain or
moisture. 2. The unit should be stored in temperatures under 25 Degree Celsius
and the battery
should be charged every 3 months to maintain its operational life.
Initial Trouble Shooting
Cause
Problem
What to do
– Power not getting to the unit after plugging in. The LED AC light does not turn on.
– The power socket might not have any power.
– The plug or socket is loose. – The AC. fuse is blown.
– Check the 220-240VAC power supply.
– Check the plug and socket. – Contact customer service.
– Emergency light does not – The unit is not plugged in. turn on after the
power went – The lamp is faulty. out. – The circuit’s wiring is loose.
– The DC fuse is blown.
– Check that the unit is plugged in. – Contact customer service. – Contact customer service. – Contact customer service.
– Emergency light only turns on for a short time after the power went out.
– The battery is not fully charged. – The battery has degraded.
– Fully charge the battery. – Contact customer service to
replace the battery
Dimension (mm)
FRONT VIEW
BACK VIEW
SIDE VIEW
How to use the remote
Remote Testing 5 30 60 secs mins mins
H 220 H 220 H 220
L 250
MCU HZ Type FRONT VIEW
L 250
MCU NC Type
197 L 250
BACK VIEW
W 80
SIDE VIEW
197 L 250
W 80
5 secs
Perform a 5 second test.
30 mins
Perform a 30-minute test.
60 mins
Perform a 60-minute test.
Increase the lamp’s brightness (only available with the HZ lamp type)
Decrease the lamp’s brightness (only available with the HZ lamp type)
Turn on/off the emergency lamp or cancel any test in progress.
H 230 H 230 H 230
Terms for Warranty and Service
1. The Warranty will only be covered if the customer fills in the “warranty
registration form” and
mail the return part back to the company within 7 days from the day of
purchase. If this is not
carried out the warranty will be considered void.
2. The warranty only covers the unit’s internal parts. The conditions and
durations for the warranty of each part is as specified and the duration of
the warranty is calculated from the date of purchase.
3. Please show your warranty card every time you contact our service center
or the dealer you
purchased the product from. 4. Products that fall into the following category
are considered not covered by the warranty.
The product was used in a way not specified in the manual. The product was
used with accessories not meeting the required specifications specified in
the manual. The product seems to have been damaged from being dropped or from
strong impact, for example, the parts are loose, dented, scrapped or
misshapen. The product has been repaired or modified by personnel not
authorized by our company.
The Warranty Void sticker is torn or removed. The product is damaged from
careless use or incorrect maintenance, for example, the battery is swollen
from overcharging, quick charging was used on the battery, the battery
terminals have been short-circuited, the unit was used until the battery was
completely discharged and not recharged immediately, the product was stored
for long periods until the Battery Checker warning activates and still it is
not plugged-in to charge or taking the battery to normal temperature
conditions and not recharging it every 1 month. The product was stored in an
unsuitable environment, for example, a location with moisture
or water vapor. The product was supplied with a faulty AC power supply such as
electrical overvoltage, electrical current surges, or lightning strikes
entering the AC power line. Damages from natural causes such as fire, being
summered in fluids, humidity, chemicals or
force majeure. Damages from insects or animals.
Note : Please read the manual carefully before installation and operation to
understand how to
properly operate the unit.
For any further questions about your product please feel free to contact SUNNY’s customer service department. Tel. (+66) 02-948-4450-2 E-mail: service@sunnyemergencylight.com
IsOn Import-Export Co., Ltd.
2915-2917 Ladprao Road, Klongjan, Bangkapi, Bangkok 10240
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>