BAOFENG UV-5G Radio

GETTING STARTED

Regulations and Safety Warnings

ATTENTION!
To help you ward off bodily injury or property loss that may arise from improper operation, please read all the information carefully before using our products. This contains instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulation.

FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Verification of harmful interference by this equipment to radio or television reception can be determined by turning it off and then on. The user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

WARNING : MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBIITED UNDER FCC RULES AND FEDERRAL LAW.

Compliance with RF Exposure Standards
The radio complies with the following RF energy exposure standards and guidelines:

• United States Federal Communications Commission, Code of Federal Regulations; 47 CFR § 1.1307, 1.1310 and 2.1093

• American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005; Canada RSS102 Issue 5 March 2015

• Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005 Edition

• RF Exposure Compliance and Control Guidelines and Operating Instructions

• To control your exposure and ensure compliance with the occupational/ controlled environmental exposure limits, always adhere to the following procedures. Guidelines:

• Do not remove the RF Exposure Label from the device.

• User awareness instructions should accompany device when transferred to other users.

• Do not use this device if the operational requirements described herein are not met. Operating Instructions:

• Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), press the Push-to-Talk (PTT) key.
  To receive calls, release the [PTT] key. Transmitting 50% of the time, or less, is important because the radio generates measurable RF energy only when transmitting (in terms of measuring for standards compliance).

• Keep the radio unit at least 2.5cm away from the face. Keeping the radio at the proper distance is important as RF exposure decreases with distance from the antenna. The antenna should be kept away from the face and eyes.

• When worn on the body, always place the radio in an approved holder, holster, case, or body harness or by use of the correct clip for this product.

• Use of non-approved accessories may result in exposure levels which exceed the FCC’s occupational/ controlled environmental RF exposure limits.

• Use of non-approved antennas, batteries, and accessories causes the radio to exceed the FCC RF exposure guidelines.

• Contact your local dealer for the product’s optional accessories.

GMRS Communication
This GMRS (General Mobile Radio Service) feature is a land-mobile service available for short-distance, two-way communications in the USA. You must have a valid FCC license to communicate on these channels. The GMRS frequencies that radio this radio uses are set aside for communicating with others while hiking, biking, and working; keeping track of family and friends at a crowded public event; checking with travel companions in another car; talking with neighbors; arranging meeting spots with others while shopping at the mall. Licensed users will be issued a call sign by the FCC, which should be used for station identification when operating this radio. GMRS users should also cooperate by engaging in permissible transmissions only, avoiding channel interference with other GMRS users, and being prudent with the length of their transmission time.

Licensing Information

USA
This two-way radio operates on GMRS (General Mobile Radio Service) frequencies which require an FCC (Federal Communications Commission) license. A user must be licensed prior to transmitting on the GMRS band with this radio. Serious penalties could result for unlicensed use of GMRS channels, in violation of FCC rules. Operation of this radio is subject to additional rules specified in 47 C.F.R. Part 95. For licensing information and application forms, please call the FCC Hotline at 800418-FORM. Request form #159 and form #605. Questions regarding the license application should be directed to the FCC at 888-CALL-FCC. Additional information is available on the FCC’s website at www.fcc.gov.

Canada
Use of Pofung radio in Canada is subject to the rules & regulations of Industry Canada (IC). IC requires no license when operated in Canada. Changes or modifications not expressly approved by PO FUNG COMPANY may void the user authority granted by the IC/FCC to operate this radio and should not be made. To comply with IC/FCC requirements, transmitter adjustments should be made only by or under the supervision of a person certified as technically qualified to perform transmitter maintenance and repairs in the private land mobile and fixed services as certified by an organization representative of the user of those services. Replacement of any transmitter component (crystal, semiconductor, etc) not authorized by the IC/FCC equipment authorization for this radio could violate IC/ FCC rules. Note: Use of this radio outside the country where it was intended to be distributed is subject to government regulations and may be prohibited.

Initial setup Safety Information
The following safety precautions should always be observed during operation, service and repair of this equipment.

• Qualified technicians shall service this equipment only.
• Do not modify the radio for any reason.
• Only use the company supplied or approved batteries and chargers.
• Do not use any portable radio that has a damaged antenna. If a damaged antenna comes into contact with your skin, a minor burn can result.
• Turn off your radio prior to entering any area with explosive and flammable materials.
• Do not charge your battery in a location with explosive and flammable materials.
• To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any area where posted notices instruct you to do so.
• Turn off your radio before boarding an aircraft; any use of a radio must be in accordance with airline regulations or crew instructions.
• Turn off your radio before entering a blasting area.
• For vehicles with an air bag, do not place a radio in the area over an air bag or in the air bag deployment area.

Main features

• Dual band (VHF/UHF) displayed
• 22 Modifiable GMRS Two-Way Channels (RX &TX)
• 88 Programmable Scanner Channels (Receive Only)
• Output power: 4W/0.5W (GMRS)
• 50 CTCSS tones and 210 DCS codes
• SOS Emergency function
• Built-in FM Radio (76-108MHz)
• 2pin Kenwood accessory jack
• TOT (Time out timer)
• Reverse function
• Busy Channel Lockout function (BCL)
• Frequency step: 2.5/5/6.25/10/12.5/25KHz
• Repeater shift · Power Save
• Operating modes: UHF/VHF, UHF/UHF, VHF/VHF
• 8 Modifiable GMRS Repeater Channels (RX & TX)
• 0 NOAA Weather Radio & Scan (Channels 118-127)
• CTCSS and DCS codes research
• 1750Hz tone for repeaters
• Tri-Color Adjustable Backlight
• VOX, Scan, Dual Watch functions
• Channel or frequency mode selection
• DTMF function
• Setting and storing of channel names
• VOICE: vocal indication of the function selected
• Frequency offset (adjustable): 0-69.990MHz
• Squelch adjustable in 9 levels
• Li-Ion 3800mAh battery pack

Maintenance

Your Two Way Radio is an electronic product of exact design and should be treated with care. The suggestions below will help you to fulfill any warranty obligations and to enjoy this product for many years.

• Do not attempt to open the radio for any reason! The radio’s precision mechanics and electronics require experience and specialized equipment; for the same reason, the radio should under no circumstances be realigned as it has already been calibrated for maximum performance. Unauthorized opening of the transceiver will void the warranty.
• Do not store the Radio under the sunshine or in hot areas.
• High temperatures can shorten the life of electronic devices, and warp or melt certain plastics.
• Do not store the radio in dusty and dirty areas.
• Keep the Radio dry. Rainwater or damp will corrode electronic circuits.
• If it appears that the Radio diffuses peculiar smell or smoke, please shut off its power immediately and take off the charger or battery from the radio.
• Do not transmit without antenna.

Programming software (optional)
WARNINGYou may be tempted to use FRS, GMRS, MURS (in the USA) or PMR446 (in Europe) frequencies.
Do note however that there are restrictions on these bands that make this transceiver illegal for use. Thanks to Pofung Programming software PRG-UV-5G, it is possible to increase the performance of your radio or to reduce its functionality by enabling or disabling some features (CTCSS, TOT, VOX, ROGER BEEP, SQUELCH, VOICE…) your programming must comply with your FCC (or other country) license certification. Any attempt to change frequencies or output power of the radio invalidates the approval. Pofung UV-5G radios ship from the manufacturer “Keypad” locked per FCC rules. You will need the programming cable to connect your radio to your computer for programming. The programming software are available for download from Pofung website: http://www.pofung.cn. When programming this radio for the first time, it is recommended you first READ the radio with the software and then save this file for future reference as it contains the default programming and settings. In addition, after you READ this radio with software, first make your programming and frequency changes, then send this edited file back to your radio.

NOTE:
GMRS channels are setup in the standardized GMRS flow. Channels 1-22 are non- repeater channels coordinating with the GMRS channel list and channels 23-30 are GMRS repeater channels. Channel List: · 22 Modifiable GMRS Two-Way Channels (Channels 1-22) – Receive and Transmit · 8 Modifiable GMRS Repeater Channels (Channels 23-30) – Receive and Transmit · 10 Fixed NOAA Weather Channels (Channels 118-127) -Receive Only · 88 Programmable Scanner Channels (Channels 00 & 31-118) – Receive Only

Content of the packaging

• 1 UV-5G transceiver with antenna
• 1 Li-Ion battery pack 3800mAh 7.4V
• 1 fast desktop charger
• 1 wall adaptor
• 1 belt clip If any item is missing, please verify with your Pofung dealer.

BATTERY INFORMATION

Charging the Battery Pack
The Li-ion battery pack is not charged at the factory; please charge it before use. Charging the battery pack for the first time after purchase or extended storage (more than 2 months) may not bring the battery pack to its normal maximum operating capacity. Best operation will require fully charging/ discharging the battery two or three times before the operating capacity will reach its best performance. The battery pack life may be depleted when it’s operating time decreases even though it has been fully and correctly charged. If this is the case, replace the battery pack.

Charger Supplied
Please use the specified charger provided by Pofung. Other models may cause explosion and personal injury. After installing the battery pack, and if the radio displays low battery with a voice prompt, please charge the battery.

Use Caution with the Li-ion Battery

• a. Do not short the battery terminals or throw the battery into a fire. Never attempt to remove the casing from the battery pack, as Pofung cannot be held responsible for any accident caused by modifying the battery.

• b. The ambient temperature should be between 5-40 (40°F – 105°F) while charging the battery. Charging outside this range may not fully charge the battery.

• c. Please turn off the radio before inserting it into the charger. It may otherwise interfere with correct charging.

• d. To avoid interfering with the charging cycle, please do not cut off the power or remove the battery during
  charging until the green light is on.

• e. Do not recharge the battery pack if it is fully charged. This may shorten the life of the battery pack or damage

• the battery pack.

• f. Do not charge the battery or the radio if it is damp. Dry it before charging to avoid damage.

WARNING
When keys, ornamental chain or other electric metals contact the battery terminal, the battery may become damage or injure a human. If the battery terminals are short circuited it will generate a lot of heat. Take care when carrying and using the battery. Remember to put the battery or radio into an insulated container. Do not put it into a metal container.

How to Charge

• a. Plug the AC adaptor into the AC outlet, and then plug the cable of the AC adaptor into the DC jack located on the back of the charger. The indicator light blinks orange and is then ready to charge a battery.
• b. Plug the battery or the radio into the charger. Make sure the battery terminals are good in contact with charging terminals. The indicator light turns to red— charging begins.
• c. It takes approximately 2-5 hours to fully charge the battery. When the lamp lights green, the charging is completed. Remove the battery or the radio unit with its battery from socket.

When charging a radio (with battery) the indicating lamp will not turn into green to show the fully charged status if the radio is powered on. Only when the radio is switched off will the lamp indicate normal operation. The radio consumes energy when it is power-on, and the charger cannot detect the correct battery voltage when the battery has been fully charged. So the charger will charge the battery in constant voltage mode and fail to indicate correctly when the battery has been fully charged.

LED Indicator

STATUS
No Battery Charge Normally
Fully Charged Trouble

LED
Green and red alternately flashing Red Green
Red blinks fast for a long time

NOTE
Trouble means battery too warm, battery short-circuited or charger short- circuited.

How to Store the Battery

• a. If the battery needs to be stored, keep it in status of 80% discharged.
• b. It should be kept in low temperature and dry environment.
• c. Keep it away from hot places and direct sunlight. » Do not short circuit the battery terminals. » Never attempt to remove the casing from the battery pack. » Never store the battery in unsafe surroundings, as a short may cause an explosion. » Do not put the battery in a hot environment or throw it into a fire, as it may cause an explosion.

INSTALLATION OF ACCESSORIES

Before the radio is ready for use we need to attach the antenna and battery pack, as well as charge the battery.

Installing the belt clip

• a. At the back of the radio there are two parallel screws mounted above the battery, remove these and thread them through the holes on the belt clip as you screw them back into the radio body.
• b. Removing the Belt Clip: Unscrew counter-clockwise to remove the belt clip.

Installing the battery pack
Before attaching or removing the battery make sure your radio is turned off by turning the power/volume knob all the way counter-clockwise.

• a. Make sure the battery is aligned in parallel with the radio body with the lower edge of the battery about 1-2cm below the edge of the radio.
• b. Once aligned with the guide-rails, slide the battery upward until you hear a click as the battery locks in place.

Remove the battery pack
To remove the battery, press the battery release above the battery pack, as you slide the battery downward.

Installing the Additional Speaker/Microphone (Optional)
Pry open the rubber MIC-Headset jack cover and then insert the Speaker / Microphone plug into the double jack.

RADIO OVERVIEW

• Buttons and controls of the radio

• A. Antenna

• B. Flashlight

• C. Power / Switch / Volume control:
  Rotate to switch on/off the radio and adjust the volume

• D. LCD display

• E. Speaker

• F. Microphone

• G. Alphanumerical keypad

• H. / keys: to select the functions/menu

• I. EXIT: Push it to exit the menu and functions

• J. *SCAN: Reverse frequency/SCAN. Press to activate the Reverse frequency; keep it pressed to activate the SCAN function

• K. 0 / SQL: quick selection of the squelch setting

• L. # : Keypad lock. Long pressure: the keypad will be locked. Short pressure: high or low power selection.

• L is displayed when you activate the low power.

• M. MENU: enter the MENU functions and confirms the selection.

• N. Led: transmission (red) ; reception (green).

• O. VFO/MR: to change the frequency or the channel mode

• P. A/B. This control is useful to select the desired frequency, VHF or UHF.

• Q. PTT

• R. MON. Long press: to activate the Monitor function. Short press: turns the flashlight on. Press it again to issue an emergency light.

• S. CALL: press it activate the FM radio. If you keep it pressed for 5 seconds you will hear an alarm note and the radio will switch to alarm mode.

• T. MIC/SP: External speaker/mike jacks. U. 3800mAh Li-Ion battery pack

Main controls and parts of the radio

LCD Display

1. These symbols show that you set a DCS or CTCSS code in tx or rx. In tx mode it appears while you are transmitting, while in rx mode it is shown also in stand-by condition.
2. Received signal strength.
3. Low power selection
4. This letter is displayed when the Dual Watch function is active.
5. VOX function enabled.
6. Appears when a positive shift is activated.
7. Appears when a negative shift is enabled.
8. Reverse frequency
9. Narrow/Wide bandwidth: N = narrow. W=Wide
10.  This icon indicates the keypad lock. To unlock it press [# ] .
11.  Battery level indicator. When the battery is almost used up, the icon starts blinking and the transmission is blocked. Charge the radio.
12.  Indicates the channel number that you stored
13. When the radio is in reception mode, this icon is displayed
14.  Depending on the setting, it will show the frequency in use, the channel name, the menu setting, etc
15.  Indicates the VFO in use and the current menu or function setting. This icon is displayed close to the band in use or to the menu settings.

Battery Level Indicator

When the battery level indicator reads the battery is depleted. At this point the radio will start beeping periodically as well as flash the backlight of the display and when voice prompts are enabled, a “Low Voltage” announcement will be heard, indicating that you need to change your battery or put your radio in the charger.

Status Indications

The status LED has a very simple and traditional design. LED Indicator Constant Red Constant Green

Main keypad controls

• [CALL] key: Press it for a short time to turn on the FM radio. Press it again to turn it off.

• If you press it for a long time you will activate the alarm function. Press it again to turn off this feature.

• [Monitor] key: Press it for a short time to light up the flashlight. If you push this button again, the flashlight will light up to strobe mode.

• Press MONI a third time to turn off the flashlight.

• To activate the Monitor function presses the button for a long time.

• [VFO / MR] key: Press it for switches between Frequency (VFO) Mode and Memory (MR) mode. Memory mode is sometimes also referred to as Channel mode.

• To save frequencies to channel memory you must be in Frequency (VFO) mode.

•  [A/B] key: Press it for switches between A (upper) and B (lower) displays.

• The frequency or channel on the selected display becomes the active listening and transmit frequency or channel.

• To save frequencies to channel memory you must be on the A display.

• When listening to broadcast FM, the [A/B] key switches between 65-75 MHz and 76-108 MHz band

•  [MENU] key: it is used for activating the MENU, choose each MENU selection and confirm the parameter.

•  [] key: Press it for more than 2 seconds, the channel and frequency will move upwards rapidly; in SCAN mode, press this control to move the scanning upwards.

•  [] key: Keep it pressed it for more than 2 seconds, the channel and frequency will move downwards rapidly; in SCAN mode, press this control to move the scanning downwards.

•  [EXIT] key: push this button to exit the functions and settings.

•  Numeric keypad

• With these keys you can input the information or your selections on the radio. In tx mode, push the number keys to send a corresponding DTMF code.

• SCAN Key

• A short momentary press of the key enables the reverse function. When listening to broadcast FM a momentary press will start the scanning. Scanning in broadcast FM will stop as soon as an active station is found, regardless of scanner resume method. To enable the scanner, press and hold the [*SCAN] key for about two seconds.

• Zero 0 Key
  The Pofung UV-5G features a battery voltage meter that the current voltage of the battery on the display. To see the voltage displayed, press and hold the [0SQL] key for about two seconds.

• key

  If you press shortly [# ] you will switch to High or Low output power. If you press this button for more than 2 seconds you will lock/unlock the keypad.

BASIC OPERATIONS

Power on the radio

NOTE : Before we turn the power on, make sure you have attached the battery and antenna.

• Turning the unit on
  To turn the unit on, simply rotate the volume/power knob clockwise until you hear a “click”. If your radio powers on correctly there should be an audible double beep after about one second and the display will show a message or flash the LCD depending on settings for about one second. Then it will display a frequency or channel. If the Voice prompt is enabled, the voice will announce “frequency mode” or “channel mode”.

• Turning the unit off
  Turn the volume/power knob counter-clock wise all the way until you hear a “click”. The unit is now off.

Adjusting the volume
To turn up the volume, turn the volume/power knob clock-wise. To turn the volume down, turn the volume/power knob counter-clock-wise. Be careful not to turn it too far, as you may inadvertently turn your radio off.

Making a call
NOTE : Press the [A/B] key to switch the main channel to the other channel if there is 2 channels shown on the display. Press the [VFO/MR] key to switch between VFO and channel display. · Channel mode call: After selecting a channel, hold down the [PTT] key to initiate a call to the current channel. Speak into the microphone with normal tone. Initiate a call, the red LED is on. · Frequency mode call: Press the [VFO/MR] key to switch to the frequency mode, the frequency range allowed entering, press the [PTT] key, a call to the current channel. Speak into the microphone with normal tone. Initiate a call, the red LED is on. · Receive a call: When you release the [PTT] key, you can answer it without any action. When receiving a call, the green LED is on.

NOTE : To ensure the best reception volume, keep the distance between the microphone and the mouth at the time of transmission from 2.5 cm to 5 cm.

Channel selection
There are two modes of operation: Frequency (VFO) mode, and Channel or Memory (MR) mode. For everyday use, Channel (MR) mode is going to be a whole lot more practical than Frequency (VFO) mode. However, Frequency (VFO) mode is very handy for experimentation out in the field. Frequency (VFO) mode is also used for programming channels into memory. In Channel (MR) mode you can navigate up and down the channel by using the and keys. Ultimately which mode you end up using will depend entirely on your use case.

Frequency (VFO) mode
In Frequency (VFO) mode you can navigate up and down the band by using the and keys. Each press will increment or decrement your frequency according to the frequency step you’ve set your transceiver to. You can also input frequencies directly on your numeric keypad with kilohertz accuracy. The following example assumes the use of a 12.5 kHz frequency step.

Example. Entering the frequency 462.5875 MHz on display A a. Use the [VFO/MR] key to switch to Frequency (VFO) mode. b. Press [A/B] until the icon appears next to the upper display. c. Enter [4][6][2][5][8][7][5] on the numeric keypad.

WARNING!
Just because you can program in a channel does not mean you’re automatically authorized to use that frequency. Transmitting on frequencies you’re not authorized to operate on is illegal, and in most jurisdictions a serious offence. If you get caught transmitting without a license you can and will get fined, and in worst case sent to jail. However, it is legal in most jurisdictions to listen. Contact your local regulatory body for further information on what laws, rules and regulations apply to your area.

Channel (MR) mode
The use of Channel (MR) mode is dependent on actually having programmed in some channels to use. Once you have channels programmed and ready, you can use the and keys to navigate between channels.

ADVANCED FEATURES

Frequency scanning
This function can scan the frequency.

• a. In frequency mode, press [*/scan] key for more than 2 seconds. The radio will start scanning the frequency
  according to the set frequency step.

• b. You can change the scanning direction with the and keys. c. Press any key to stop the scanning. Note: for Scan mode, see Menu No.18.

Channel scanning

This function can scan the channels. a. In channels mode, press [*scan] key for more than 2 seconds. The radio will start scanning according to the
channel you set. b. You can change the scanning direction with the and keys. c. Press any key to stop scanning. Note: for Scan mode, see Menu No.18.

Search CTCSS/DCS Code
With this function you can search and store the CTCSS/DCS code used by other radios. Procedure: a. In frequency mode press [MENU]+[1][1]. b. Press [MENU] key again. c. Press [*scan] key; CT will blink on the display. d. When another radio is transmitting, the display will show the CTCSS/DCS code. e. After searching the CTCSS code, the radio will beep and stop scanning. f. After setting, press [MR/VFO] key for confirmation and store, or press [PTT] or [EXIT] key to return to standby
mode. NOTE 1: the DCS scanning has the same procedure of CTCSS code, but you have to select MENU+10 to enter scanning. NOTE 2: if CTCSS has not searched the code, you can search using the DCS mode.

CursorConversion (A/B)
Directly press [A/B] key to move the cursor up and down. Then, you can modify or confirm the parameters indicated by the cursor. Important1: UV-5G has a dual-frequency display function. In frequency mode, you will see on the display two different receiving and transmitting frequencies; while in channel mode the two different channels will be displayed. Important2: In frequency or channel mode, press the [A/B] key to shift between the main channel A and the sub-channel B on the display indicates on which channel (main channel A or sub channel B) you are operating. is displayed next to the channel.

High/low power fast selection
Your radio has 2 power level settings. In GMRS channels 1 ~ 7 and 15 ~ 30, press [# ] key to shift between high and low power. Note: You cannot adjust the power setting on the 8-14 channels. They are set to Lo power per FCC regulations.

Keypad lock
This function locks the keypad to prevent accidental pressure of the controls. To unlock the keypad, press [# ] for more than 2 seconds.

FM Radio (FM)
The frequency range to listen to the radio is 65-108MHz. When listening to broadcast FM, press [A / B] key switches between 65-75 MHz and 76-108 MHz band.

• a. In frequency or channel mode, Press [CALL] to turn on the radio.
• b. Select the desired radio frequency with the or keys or input the frequency. or  Press [* SCAN] to automatically search a radio station.
• c. Press [CALL] to exit FM radio. Note: while you are listening to the radio, the frequency or channel of A / B receiving signal will automatically switch to the frequency or channel mode for normal transmitting and receiving. When the signal disappears the radio will automatically switch again to FM radio mode.

Flashlight

This function is very useful for night illumination. To turn it on press MON; push it again, the flash light will be strobe; push it again: it will turn off.

1000Hz, 1450Hz, 1750Hz Tone-burst

To send out a tone-burst; you simultaneously will press a key while holding down the PTT. No further configuration required using this feature.

The following configurations will transmit accordingly:

• [PTT] + [CALL] = Transmits 1000Hz Tone Burst
• [PTT] + [VFO/MR] = Transmits 1450Hz Tone Burst
• [PTT] + [A/B] = Transmits 1750Hz Tone Burst

If you have the keypad lock enabled on your radio, you can still send a 1750Hz tone the regular way without having to unlock your radio.

NOAA weather radio/ scan

Your radio has a NOAA weather radio function, to enable the user to receive weather reports from designated NOAA stations. Your radio also has a NOAA weather scan function to enable the user to scan all 10 channels of the NOAA weather radio. To select the NOAA channel, enter the channel number 118 ~ 127 directly in the channel mode or press the or keys until the channel 118 ~ 127. To scan the NOAAWEATHER channel, press and hold the [* SCAN] key for 3 seconds in channel mode. During scanning, press any key to exit the scanning state. NOTE: The radio’s NOAA weather channel is in the 118-127 channels, and the detailed frequency is NOAA WEATHER (WX) RADIO FREQUENCY CHART.

Manual Programming (Channels Memory)
Memory channels are an easy way to store commonly used frequencies so that they can easily be retrieved at a later date. The Pofung UV-5G features 128 memory channels that each can hold: Receive and transmit frequencies, transmit power, group signaling information, bandwidth, ANI/ PTT-ID settings and a six character alphanumeric identifier or channel name 1 .

Frequency Mode vs. Channel Mode Switch between Modes by Using the [VFO/MR] Front Panel Button. These two modes have different functions and are often confused.
Frequency Mode (VFO) : Used for a temporary frequency assignment, such as a test frequency or quick field programming if permitted. Channel Mode (MR) : Used for selecting preprogrammed channels.
Ex 1. Programming a Channel Repeater Offset with CTCSS Tone EXAMPLE New memory in Channel 10:

RX = 462.5750 MHz
TX = 467.5750 MHz (This is a (+ 5) Offset)
TX CTCSS tone 123.0

• a. Change from Menu to Menu by pressing the [EXIT] key.
• b. Set radio to VFO Mode by pressing [VFO/MR] Channel number at the right will disappear.
• c. [MENU] [2][8][MENU] [1] [0] [MENU] [EXIT] Deletes Prior Data in channel (Ex. 10)
• d. [MENU] [1][3] [MENU] 123.0 [MENU] [EXIT] Selects desired TX encode tone
• e. Enter RX frequency (Ex. 462.5750)
• f. [MENU] [2][7] [MENU] [1][0] [MENU] Enter the desired channel (Ex 10) –>>[EXIT] RX has been added
• g. Enter TX frequency (Ex. 467.5750)
• h. [MENU] [2][7] [MENU] [1][0] [MENU]

Ex 2. Programming a Simplex Channel with CTCSS tone

EXAMPLE New memory in Channel 10:
RX = 462.5750 MHz
TX CTCSS tone 123.0

• a. Change from Menu to Menu by pressing the [EXIT] button.
• b. Set radio to VFO Mode by pressing [VFO/MR] Channel number at the right will disappear.
• c. [MENU] [2][8] [MENU] [1] [0] [MENU] [EXIT] Deletes Prior Data in channel (Ex. 10)
• d. [MENU] [1][3] [MENU] 123.0 [MENU] [EXIT] Select desired TX encode tone (Ex 123 CTCSS) –>>Use [A/B] to select Upper display
• e. Enter RX frequency (Ex. 462.5750)
• f. [MENU] [2][7] [MENU] [1][0] [MENU] Enter the desired channel (Ex 10) –>> [EXIT] Channel has been added
• g. [VFO/MR] Return to MR Mode. Channel number will re-appear.

Repeaters Programming
The following instructions assume that you know what transmit and receive frequencies your repeater employs, and that you’re authorized to use it.

• a. Set the radio to Frequency (VFO) mode with the [VFO/MR] key.
• b. Enter the repeater’s output (your receiving) frequency by either using the and keys, or by entering it directly on the numerical keypad.
• c. Press the [MENU] key to enter the menu.
• d. Enter [2][6] on the numeric keypad to get to frequency offset.
• e. Press [MENU] key to select.
• f. Use the numerical keypad to enter the specified frequency offset. See the section called “26 OFFSET – Frequency shift amount” for details.
• g. Press [MENU] to confirm and save. h. Enter [2][5] on the numeric keypad to get to offset direction.\
• i. Use the / keys to select + (positive) or – (negative) offset.
• j. Press [MENU] to confirm and save.
• k. Optional:
  • a). Save to memory, see the section called “Manual programming” for details.
  • b). Set up CTCSS; see the section called “CTCSS” for details.

l. Press [EXIT] to exit the menu. If everything went well, you should be able to make a test call through the repeater.

NOTE:
If you’re experiencing problems making a connection to the repeater, check your settings and/or go through the procedure again. Certain Amateur Radio repeaters (especially in Europe) use a 1750Hz tone burst to open up the repeater. To see how this is done with the Pofung UV-5G, see the section called “1750Hz Tone-burst”. If you’re still unable to make a connection, contact the person in charge of the radio system with your employer or your local amateur radio club, as the case may be. If you for some reason want to listen to the repeater’s input frequency instead, press [*/SCAN] key momentarily and you’ll reverse your transmit and receive frequencies. This is indicated in the LCD on the radio with an R in the top row, next to the + and – for the offset direction.

WORKING THE MENU SYSTEM

For a complete reference on available menu items and parameters, see Appendix E, Shortcut Menu operations. Note: in channel mode, the setting of these features is not possible: CTCSS/ DCS tones, wide/narrow bandwidth, PTT-ID, Busy channel lock out, channel name edit.

Basic use
Using the menu with arrow keys a. Press the [MENU] key to enter the menu. b. Use the [] and [] keys to navigate between menu items. c. Once you find the desired menu item, press [MENU] again to select that menu item. d. Use the [] and [] keys to select the desired parameter. e. When you’ve selected the parameter you want to set for a given menu item;

• a). To confirm your selection, press [MENU] and it will save your setting and bring you back to the main menu.
• b). To cancel your changes, press [EXIT] and it will reset that menu item and bring you out of the menu entirely.
• f. To exit out of the menu at any time, press the [EXIT] key.

Using short-cuts
As you may have noticed if you looked at Appendix E, Shortcut Menu operations, every menu item has a numerical value associated with it. These numbers can be used for direct access of any given menu item. The parameters also have a number associated with them, see Appendix E, Shortcut Menu operations for details. Using the menu with short-cuts

• a. Press the [MENU] key to enter the menu.
• b. Use the numerical keypad to enter the number of the menu item.
• c. To enter the menu item, press the [MENU] key.
• d. For entering the desired parameter you have two options:
  • a). Use the arrow keys as we did in the previous section; or
  • b). Use the numerical keypad to enter the numerical short-cut code.
• e. And just as in the previous section;
  • a). To confirm your selection, press [MENU] and it will save your setting and bring you back to the main menu.
  • b). To cancel your changes, press [EXIT] and it will reset that menu item and bring you out of the menu entirely.
• f. To exit out of the menu at any time, press the [EXIT] key. g. All further examples and procedures in this manual will use the numerical menu short- cuts.

Functions and operations
(1) Squelch level (SQL) – MENU No.0
Thanks to this function you can adjust the squelch in 10 different levels: · level 0: opened squelch. With this setting, UV-5G will detect all signals, also the weakest ones, but will also receive the background noise or undesired signals. · levels 1- 9: level 1 (lowest squelch level), level 9 (highest squelch level). If the squelch is set to the highest level, the radio will receive the strongest signals only.
(2) Step frequency (STEP) – MENU No.1
This function lets you select the desired frequency step. The selectable steps are the following: 2.5/5.0/6.25/10.0/12.5/20.0/25.0/50.0 KHz Note: in channel mode, this function cannot be modified.
(3) Output power (TXP) – MENU No.2
In this MENU you can select the high/low output power. Low power = 0.5W; High power = 4W Note: select the output power can improve the quality of the call, while the low output power can reduce the radiation and the battery capacity loss. Press the fast key “# ” to switch between the high or low output powers.
(4) Battery save (SAVE) – MENU No.3
The power save feature enables a reduction in the consumption of the battery when the radio is in standby. You have 5 selections available: OFF / 1:1 / 1:2 / 1:3 / 1:4. For example: 1:1 = 1s’ working and 1s’battery saving. 1:2 = 1s’ working and 2s’ battery saving.
(5) VOX Function (VOX) – MENU No.4
This function allows hands-free conversations: just speak in the direction of the microphone and the communication will be automatically activated. You can choose amongst 11 levels: OFF-10. 1 is the highest level, 10 is the lowest one. Note: the higher is the level, the higher is the microphone sensitivity. The VOX function cannot be modified in SCAN and FM radio mode.
(6) Narrow /Wide bandwidth – MENU No.5
This function is used to set the working bandwidth of the radio. NARROW: 12.5KHz Wide: 25KHz Note: In channel mode, this function cannot be modified.
(7) Backlight (ABR) – MENU No. 6
With this function you can adjust the auto off time of the display backlight (1-5s). Note: we suggest you setting 4-5s levels.
(8) Dual Watch Operation (TDR) – MENU No. 7
When this function is activated, you can receive the frequency of channel A and channel B at the same time. If a signal is detected, the/ pointer will blink on the corresponding channel or frequency. Note: In Dual Watch operation mode, you can change the parameter of AB channel or frequency freely.
(9) Keypad beep (BEEP) – MENU No. 8
When this function is enabled, every time a button is pressed, you will hear a beep tone.
(10) Time-Out-Timer (TOT) – MENU No.9
The TOT function is used to prevent a too long transmission and limits the tx time: TOT temporarily stops the transmission if the radio has been used beyond the max pre-set time (for example 15s, 30s, 45s, etc).
(11) Receiving DCS (R-DCS) – MENU No.10
DCS codes are similar to access codes and can be added to channels, so as to create a sort of personal channel. They enable the radio to communicate with the users that are tuned on the same channel and have set the same DCS code. You can choose amongst: · OFF: OFF · R-DCS: D023N-D754N (Normal DCS) · R-DCS: D023I-D754I (Inverse DCS) Note: In UV-5G there are 208 groups of normal and inverse DCS codes. This function cannot be amended in channel mode.
(12) Receiving CTCSS (R-CTCSS) – MENU No.11
As DCS codes, the CTCSS codes can be added to the channels for creating new private channels. Note: there are 50 groups of CTCSS tones. In channel mode the CTCSS tones cannot be changed.
(13) Transmitting DCS – (T-DCS) – MENU No.12
In this Menu you activate DCS codes in tx mode. You can choose between normal R-DCS (D023N-D754N) and inverted R-DCS (D023I-D754I) Note: the groups of DCS codes are 208. DCS codes cannot be changed in channel mode.
(14) Transmitting CTCSS (T-CTCSS) – MENU No.13
In this Menu you can set a CTCSS tone in tx mode. You can choose: OFF or CTCSS (67.0 to 254.1 Hz) Note: there are 50 groups of CTCSS tones. In channel mode the CTCSS tones cannot be changed.
(15) Voice function (VOICE) – MENU No. 14
With this function, you activate a voice that informs you about any operation/ selection you are doing.
(16) ANI-ID (ANI-ID) – MENU No.15
With this function you can set your ID-code. It can be programmed by the proper programming software. You can edit up to 5 digits.
(17) DTMFST (DTMFST) – MENU No.16
Determines when DTMF Side Tones can be heard from the transceiver speaker. (18) Signal code (S-CODE) – MENU No.17 Selects 1 of 15 DTMF codes. The DTMF codes are programmed with software and are up to 5 digits each.
(19) SCAN Resume Mode (SC-REV) – MENU No.18
Thanks to this function, UV-5G can SCAN in frequency or channel mode. You can choose amongst three options: TO: Time-operated SCAN Whenever a signal is detected, the radio will suspend the SCAN for 5 seconds, and then will continue to SCAN even if the signal is still present. CO: Carrier-operated SCAN Whenever a signal is detected, the radio will stop scanning. It will resume to SCAN once the signal will disappear. SE: Search SCAN The radio will stop scanning once a signal is detected.
(20) PTT-ID (PTT-ID) – MENU No.19
With this function you can decide when sending the ANI-ID code in tx mode. You can choose amongst 4 possibilities.

• OFF: press PTT to turn it off
• BOT: the code is sent when you press the PTT
• EOT: the code is sent when the PTT is released
• BOTH: the code is sent when you press and release the PTT

Note : select `OFF’ when using in case of affecting the radio.

(21) PTT ID delay (PTT-LT) – MENU No.20
In this MENU you can set the delay time (0-30ms) sending the PTT-ID. Note: select `0′ in normal using.
(22) Channel A Display Mode (MDF-A) – MENU No.21
This function is used to set the display mode of channel A.

Display modes:

• FREQ.: Frequency + channel No.
• CH : Channel number
• NAME : Channel name

Note : Channel name mode must be set by the programming software. Up to three numbers or characters can be edited.

(23) Channel B Display Mode (MDF-B) – MENU No.22
This function is used to set the display mode of channel B.

Display modes:

• FREQ.: Frequency + channel No.
• CH : Channel number
• NAME : Channel name

Note : Channel name mode must be set by the programming software. Up to three numbers or characters can be edited.

(24) Busy Channel Lock (BCL) – MENU No. 23
When this function is on, it may prevent other radios’ interference. If the selected channel is being used by other radios, when you press key PTT, your radio cannot transmit. Release the PTT and transmit as soon as the frequency is no longer busy.
(25) Auto Keypad Lock (AUTOLK) – MENU No.24
When this feature is activated, the keypad will be automatically locked after 15s; this prevents accidental pressure of any keys.
(26) Frequency offset direction (SFT-D) – MENU No.25
Using this function, you can set the direction of the frequency offset in rx and tx. You have the following options: +: Positive offset; -: Negative offset; OFF: no offset Note: you should set different frequency deviation according to the repeaters selected. This function is not enabled in channel mode.
(27) Frequency offset (OFFSET) – MENU No. 26
In this MENU you can set the deviation between tx and rx. The frequency offset of this radio is 0-69.990MHz.
(28) Channel store – (MEM-CH) – MENU No. 27
When the radio is in frequency working mode or standby mode, input the desired frequency or parameters directly. To set a CTCSS tone or a DCS code in tx or rx on the stored channel, refer to paragraphs MENU 10-13 Note: You cannot overwrite a stored channel, you have to delete it first. See following paragraph No.28.
(29) Channel Delete (DEL-CH) – MENU No.28
In this menu you can delete a channel of the radio.
(30) Standby backlight (WT-LED) – MENU No.29
In this MENU you can choose the color of the backlight when the radio is in standby mode. You can choose amongst: · OFF (backlight off) · BLUE · PURPLE · ORANGE
(31) RX backlight (RX-LED) – MENU No. 30
In this MENU you can choose the backlight color when the radio is receiving. You can choose amongst: · OFF (backlight off) · BLUE · PURPLE · ORANGE
(32) TX backlight (TX-LED) – MENU No.31
You can choose the backlight color when the radio is transmitting. Available colors:

• OFF (backlight off)
• BLUE
• PURPLE
• ORANGE

(33) Alarm Mode (AL-MOD) – MENU No.32
This function can set the tone alarm/code alarm/site alarm of the radio. Keep pressed the [CALL] key for 3 seconds to start the alarm tone. The following three options can be selected: · SITE: the speaker emits an alarm tone but the radio doesn’t transmit; · TONE: the speaker emits an alarm tone and the radio transmits it; · CODE: the speaker emits an alarm tone and the radio transmits it followed by ANI-ID code.
(34) Frequency band (BAND) – Menu No.33
In frequency mode, press the [BAND] key to choose the desired frequency band. VHF: 136-174MHz RX UHF: 400-520MHz (RX) Note: This function is applicable to some models with [BAND] key.
(35) Dual Watch (TDR-AB) – Menu No.34
When this function is on, you may receive signals of A/B channel or frequency. It can also be used for cross band receiving and transmitting. You can choose amongst the following settings: OFF: UV-5G can receive in both VFO (not simultaneously); or will blink on the transmitting frequency band.

A: the radio can receive in both VFO (not simultaneously) but can transmit in VFO A only.
B: UV-5G can receive in both VFO (not simultaneously) but can transmit in VFO B only. If you choose option A, it means that 462.575MHz is the tx frequency band, while 467.5875MHz is the rx frequency band; the upper VFO shows 462.575 MHz while in the lower VFO 467.5875MHz will be displayed; you can receive on both 462.575 MHz and 467.5875 MHz, but can transmit on 462.575 MHz only. While if you choose option B, 467.5875MHz is the tx frequency band and 462.575MHz is the rx frequency band. In the upper VFO 462.575 MHz will be displayed while the lower VFO will show 467.5875 MHz; you can receive on both 462.575 MHz and 467.5875 MHz, but transmit on 467.5875 MHz only. Example: the LCD displays
(36) Side tone elimination (STE) – Menu No. 35
This feature is helpful to eliminate the annoying audio tone after the transmission is finished (end transmission noise muffler).
(37) Side tone elimination in communication through repeater (RP-STE) – Menu No. 36
This function is used when the radio operates through a repeater; when the PTT is released, the repeater will emit the end transmission tone to confirm it is working. Available settings: OFF 1,2,3,4,5,….10 to set the delay time. Note: Please disable this function in normal using, lest affect your normal conversation.
(38) Delay time of side tone elimination in communication through repeater (RPT-RL) – Menu No.37
With this function you have the confirmation that the repeater has transferred the signal. You can choose amongst: OFF 1,2,3,4,5,….10 to set the delay time.
(39) Display mode at the turning on (PONMSG) Menu No.38
With this function you can set the display mode when the radio is turned on. Available options: · FULL: full frequency character is displayed. · MSG: UV-5G is displayed.
(40) Roger beep (ROGER) – Menu No. 39
When the PTT is released, the radio will beep to confirm to other users that you have finished your transmission and that they can start talking.
(41) Reset (RESET) – Menu No.40
With this function you can reset the transceiver to the factory-programmed settings and parameters. After that, you can set the desired functions. There are two types of reset: ·

• VFO: Menu Reset
• ALL: Menu and channel Reset

ON-LINE SERVICE AND SUPPORT

The Pofung website provides additional information about obtaining service or support for the Pofung line of two-way radios and accessories.
Visit : www.pofung.cn Mail : service@pofung.cn

FCC Licensing Information
This pofung radio operates on Commercial/ Land Mobile frequencies which require a license from the Federal Communications Commission (FCC) for business, personal, education and recreational use. To obtain forms, call the FCC forms hotline at: 1-800-418-3676 or go to http://www.fcc.gov For questions concerning commercial licensing, contact the FCC at 1-888CALL-FCC (1-888-225-5322).

Appendix A. ­ Trouble shooting guide

NOTE : If the above solutions cannot fix your problems, or you may have some other queries, please contact your dealer for more technical support.

Appendix B. – Technical Specifications

| Phenomena| Analysis| Solution
---|---|---|---
| You cannot turn on the radio.| The battery may be installed improperly.| Remove and reattach the battery.
| The battery power may run out.| Recharge or replace the battery.
| The battery may suffer from poor contact caused by dirty or damaged battery contacts.| Clean the battery contacts or replace the battery.
| During receiving, the voice is weak or intermittent.| The battery voltage maybe low.| Recharge or replace the battery.
| The volume level may be low.| Increase the volume.
| The antenna maybe loose or maybe installed incorrectly.| Turnoff the radio, and then remove and reattach the antenna.
| The speaker maybe blocked.| Clean the surface of the speaker.
| You cannot communicate with other group members.| The frequency or signaling type maybe inconsistent with that of other members.| Verify that your TX/RX frequency and signaling type are correct.
| You may be too far away from other members.| Move towards other members.
| You hear unknown voices or noise.| You may be interrupted by radios using the same frequency.| Change the frequency, or adjust the squelch level.
| The radio in analog mode maybe set with no signaling.| Request your dealer to set signaling for the current channel to avoid interference
| You are unable to hear anyone because of too much noise and hiss.| You may be too far away from other members.| Move towards other members.
| You may be in an unfavorable position. For example, your communication may be blocked by| Move to an open and flat area, restart the radio, and try again.
| high buildings or blocked in an underground area.| |
It may be the result of external disturbance (such as electromagnetic interference).| Stay away from equipment that may cause interference.|
The radio keeps transmitting.| VOX may be turned on or the headset is not installed in place| Turn off the VOX function. Check that the headphones are in place.|
You cannot use the keys.| The keypad may not work temporarily.| Restart the radio.|

General

• Frequency Range (VHF)136-174MHz (Only RX)
• (UHF)400-520MHz (Only Rx)
• 76-108Mhz (Only Rx)
• GMRS 462.5500 ~ 467.7250 MHz (RX & TX)
• Memory Channel 30 GMRS
• Channels + 10 NOAA
• Weather + 88 Scanner Channels
• Operation Voltage DC 7.4 V ±10%
• Battery Capacity 3800mAH (Li-Ion)
• Frequency Stability ±2.5ppm
• Operating Temperature -20℃ to +60℃
• Mode of Operation Simplex
• Antenna Impedance 50ohm

Transmitter Part

• RF Output Power 4W/0.5W
• FM Modulation 11K0F3E@12.5KHz /16K0F3E@25KHz
• Spurious Emission -36dBm＜1GHz， -30dBm＞1GHz
• Adjacent Channel Power 60dB @ 12.5KHz
• Transmission current ≤1600mA

Receiver Part

• Receive Sensitivity 0.25μV (12dB SINAD)
• Adjacent Channel Selectivity ≥55dB@12.5KHz
• Inter Modulation and Rejection ≥55dB@12.5KHz
• Conducted Spurious Emission ≤-57dB@12.5KHz
• Rated Audio Power Output 1W @16 ohms
• Receive current ≤380mA
• Rated Audio Distortion ≤5%

Appendix C. – GMRS Frequency Chart (MHz)

CH.No| CH.Freq.| CH.No| CH.Freq.| CH.No| CH.Freq.
---|---|---|---|---|---
1| 462.5625| 11| 467.6375| 21| 462.7000
2| 462.5875| 12| 467.6625| 22| 462.7250
3| 462.6125| 13| 467.6875| 23| 467.5500
4| 462.6375| 14| 467.7125| 24| 467.5750
5| 462.6625| 15| 462.5500| 25| 467.6000
6| 462.6875| 16| 462.5750| 26| 467.6250
7| 462.7125| 17| 462.6000| 27| 467.6500
8| 467.5625| 18| 462.6250| 28| 467.6750
9| 467.5875| 19| 462.6500| 29| 467.7000
10| 467.6125| 20| 462.6750| 30| 467.7250

Appendix D. – Weather Channel Assignments

Channel Number| RX Frequency  MHz| Weather Channel| Channel Number| RX Frequency  MHz| Weather Channel
---|---|---|---|---|---
118| 162.550| NOAA1| 123| 162.500| NOAA6
119| 162.400| NOAA2| 124| 162.525| NOAA7
120| 162.475| NOAA3| 125| 161.650| CANADA
121| 162.425| NOAA4| 126| 161.775| CANADA
122| 162.450| NOAA5| 127| 163.275| NOAA8

Appendix E. – Shortcut Menu operations
Appendix F. – CTCSS Table

Number| Frequency| Number| Frequency| Number| Frequency| Number| Frequency| Number| Frequency
---|---|---|---|---|---|---|---|---|---
1| 67.0| 2| 69.3| 3| 71.9| 4| 74.4| 5| 77.0
6| 79.7| 7| 82.5| 8| 85.4| 9| 88.5| 10| 91.5
11| 94.8| 12| 97.4| 13| 100| 14| 103.5| 15| 107.2
16| 110.9| 17| 114.8| 18| 118.8| 19| 123.0| 20| 127.3
21| 131.8| 22| 136.5| 23| 141.3| 24| 146.2| 25| 151.4
26| 156.7| 27| 159.8| 28| 162.2| 29| 165.5| 30| 167.9
31| 171.3| 32| 173.8| 33| 177.3| 34| 179.9| 35| 183.5
36| 186.2| 37| 189.9| 38| 192.8| 39| 196.6| 40| 199.5
41| 203.5| 42| 206.5| 43| 210.7| 44| 218.1| 45| 225.7
46| 229.1| 47| 233.6| 48| 241.8| 49| 250.3| 50| 254.1

Appendix G. – DCS Table

WARNING
Our PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY radio generators RF electromagnetic energy during transmit mode.This radio is designed for and classified as“Occupational Use Only”,meaning it must be used only during the course of employment by individuals aware of the hazards,and the ways To Minimize Such hazards. This radio is NOT intended for use by the“General Population” in an uncontrolled environment. This radio has been tested and complies with the FCC RF exposure limits for“Occupational Use Only”. Inaddition, our PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans:

• IEEE Std. 1528:2013 and KDB447498, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields.
• American National Standards Institute (C95.1-1992), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz.
• American National Standards Institute (C95.3-1992), IEEE Recommended Practice for the Measurement of

Potentially Hazardous Electromagnetic Fields-RF and Microwave. The information listed above provides the user with the information needed to make him or her aware of RF exposure, and what to do to as-sure that this radio operates with the FCC RF exposure limits of this radio. Electromagnetic Interference/Compatibility During transmissions, PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals, aircraft, and blasting sites.

Occupational/Controlled Use
The radio transmitter is used in situations in which persons are exposed as consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure.

Attention:
This radio complieswith IEEE and ICNIRP exposure limits for occupational/controlled RF exposure emvironment at operating duty factors of up to 50% and is authorized by the FCC for occupational use only. An appropriate warning lable is affixed to all units. In order to comply with RF exposure requirements, a minimum distance of 2.5 cm must be maintained when held-to-face, and body-worn operations are restricted to the approved original acessories (belt clip), a minimum distance of 0 cm. Do not use this device when antenna shows obvious damages. This product is compliance to FCC RF Exposure requirements and refers to FCC website https://apps.fcc.gov/oetcf/eas/reports/GenericSearch.cfm search for FCC ID: 2AJGM-UV5G to gain further information include SAR Values.

Disclaimer
The Company endeavors to achieve the accuracy and completeness of this manual, but no warranty of accuracy or reliability is given. All the specifications and designs are subject to change without notice due to continuous technological development. No part of this manual may be copied, modified, translated, or distributed in any manner without the prior written consent of the Company.

PO FUNG ELECTRONIC（HK）INTERNATIOANL GROUP COMPANY ADD: 3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN HONGKONG Print version : P51UVFCC V1

References

• Pofung
• FCC OET Authorization Search

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>