thermaltake SMART BX3 750W Smart Bronze Power Supply Instructions
- June 17, 2024
- thermaltake
Table of Contents
SMART BX3 750W / 650W / 550W
Warnings and Caution
-
Do not unplug the AC power cord when the power supply is in use.
Doing so may cause damage to your components. -
Do not place the power supply in high humidity and /or temperature environment.
-
. High voltages exist in the power supply. Do not open the power supply case unless you are an authorized service technician or electrician. Doing so will void the warranty.
-
The power supply should be powered by the source indicated on the
rating label. -
Make sure all cables are plugged in properly. Loose and improper connections would damage the power supply and your system.
-
Please use only genuine Thermaltake modular cables with Thermaltake power supply models. Third-party cables might not be compatible and could cause serious damage to your system and power supply.
The warranty is voided with the use of third-party cables. -
All warranties and guarantees will be voided, if failure to comply with any of the warnings and cautions covered in this label.
Components Check
– SMART BX3 power supply unit
– AC power cord
– Cable straps x 4
– User manual
– Mounting screw x 4
Powwer Connector Introduction
CABLE⇒
Wattage ⇓| | | | |
---|---|---|---|---|---
Main Power Connector (24 Pin)| ATX Connector (4+4 Pin)| SATA Connector (5
Pin)| PCIe Connector (6+2 Pin)| Peripheral Connector (4 Pin)
750W| 1| 2| 4| 2| 4
650W| 1| 2| 4| 2| 4
550W| 1| 1| 4| 2| 4
Output Specification
Continuous Power| AC INPUT| Input Voltage: 100 – 240V~ ;
Input Current: 15A – 6A ; Frequency: 50Hz / 60Hz
---|---|---
750W| DC OUTPUT| +3.3V| +5V| +12V| -12V| +5VSB
Max Output Current| 18A| 18A| 62.5A| 0.3A| 3A
Max Output Power| 110W| 750W| 3.6W| 15W
Continuous Power| AC INPUT| Input Voltage: 100 – 240V~ ;
Input Current: 15A – 6A ; Frequency: 50Hz / 60Hz
650W| DC OUTPUT| +3.3V| +5V| +12V| -12V| +5VSB
Max Output Current| 18A| 18A| 54.2A| 0.3A| 3A
Max Output Power| 110W| 650W| 3.6W| 15W
Continuous Power| AC INPUT| Input Voltage: 100 – 240V~ ;
Input Current: 12A – 5A ; Frequency: 50Hz / 60Hz
550W| DC OUTPUT| +3.3V| +5V| +12V| -12V| +5VSB
Max Output Current| 16A| 16A| 45.85A| 0.3A| 3A
Max Output Power| 105W| 550W| 3.6W| 15W
Installation Steps
Note: Make sure that your system is turned off and unplugged.
Disconnect the AC power cord from your old power supply.
-
Open your computer chassis; please refer to the instruction manual provided with your chassis.
-
Install the PSU into the case with the four screws provided.
-
If your motherboard requires a 24pin Main Power connector, please connect the 24pin Main Power connector to the motherboard.
-
1. For motherboard that only requires a 4pin ATX 12V(CPU) connector, please detach a 4pin connector from the 4+4pin ATX 12V connector and connect it to the motherboard. (Either one of the 4pin from the 4+4pin ATX 12V connector will work)
4.2 For motherboard that requires a single 8pin EPS connector, please use the 4+4pin connector from the power supply. -
Connect other periphreal power connectors to devices such as hard drives, optical drives, etc.
-
If your graphic card requires PCI-E power connector, please connect corresponding PCI-E connector instructed by your graphic card’s user manual. Please note the power supply utilizes an unique 6+2pin PCI-E connector that can be effectively used as a single 8pin or 6pin PCI-E connector. To use it a 6pin PCI-E connector, please detach the 2pin connector from the 6+2pin connector.
-
Close your computer case and connect the AC power cord to the power supply AC inlet.
Attention!
As this power supply is equipped with Smart Zero Fan, the fan will start
running when certain temperature is reached. It is a normal if the fan does
not operate when computer is at a low working load.
Total Protection
– Over Voltage Protection
| +3.3V | +5V | +12V |
|---|---|---|
| 3.76~4.3V | 5.74~7.0V | 13.4~15.6V |
– Under Voltage Protection
| +3.3V | +5V | +12V |
|---|---|---|
| 2.0~2.6V | 3.3~3.9V | 8.5~9.7V |
– Over Current Protection
| Wattage | +3.3V | +5V | +12V |
|---|---|---|---|
| 750W | 25~40A | 25~40A | 106~125A |
| 650W | 92~108A | ||
| 550W | 77.5~91.7A |
EMI & SAFETY
| EMI Regulatory | MEET FCC |
|---|---|
| SAFETY Standards | MEET cTUVus, ICES, CB, CCC, CE, EAC, BIS, UKCA, LVD, TUV, |
BSMI and FCC. CAN ICES-003(B) / NMB-003(B).
Environments
| Operating temperature | 5°C to +40°C |
|---|---|
| Operating humidity | 20% to 85%,non-condensing |
| MTBF | > 100,000 hours |
Trouble-Shooting
If the power supply fails to function properly, please follow the troubleshooting guide before application for service:
- Is the power cord plugged properly into electrical outlet and into the power supply AC inlet?
- Please make sure the I/O switch on the power supply is switched to I position.
- Please make sure all power connectors are properly connected to all the devices.
- If connected to a UPS unit, is the UPS on and plugged in?
If the power supply is still unable to function properly after following the above instruction, please contact your local store or Tt branch office for after sales service. You may also refer to Thermaltake’s website for more technical support: thermaltake.com
Documents / Resources
|
thermaltake SMART BX3 750W Smart Bronze Power
Supply
[pdf] Instructions
750W, 650W, 550W, SMART BX3, SMART BX3 750W Smart Bronze Power Supply, 750W
Smart Bronze Power Supply, Smart Bronze Power Supply, Bronze Power Supply,
Power Supply, Supply
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>