MechMaxx P4206 Wood Chipper Instruction Manual

MechMaxx P4206 Wood Chipper

Your new Wood Chipper offers quality construction, and is easy and safe to operate. With proper use and care, it is designed to give you many years of dependable service.
Prepare to experience the durability to take on any job with the ease, portability, and convenience of your new Wood Chipper !

MAX performance,MAX Value,MAX Support that’s Wood Chipper
Enhanced design features come standard Engineered for the best user experience Quality metal parts are used instead of plastic A robust warranty supports all products Budget-friendly prices make it practical

SPECIFICATIONS

OVERALL DIMENSIONS

SAFETY SIGNS

The rating plate on your machine may show symbols. These represent important information about the product or instructions on its use.

SAFETY

GENERAL SAFETY RULES

• Read this manual and labels affixed to the machine to understand its limitations and potential hazards
• Be thoroughly familiar with the controls and their proper operation. Know how to stop the machine and disengage the controls quickly.
• Make sure to read and understand all the instructions and safety precautions as outlined in the Engine Manufactur- er’s manual packed separately with your unit. Do not attempt to operate the machine until you fully understand how to properly operate and maintain the engine and how to avoid accidental injuries and/or property damage.
• If the unit is to be used by someone other than original purchaser or loaned, rented, or sold, always provide this manual and any needed safety training before operation.
• The user can prevent and is responsible for accidents or injuries that may occur to themselves, other people, and property. Do not force the machine. Use the correct machine for your application. The correct machine will do the job more efficiently and safer at the rate it was designed.

PERSONAL SAFETY

• Do not permit children to operate this machine at any time. Keep children, pets, and other people not using the unit away from the work area. Be alert and shut off unit if anyone enters work area.
• Keep children under the watch- ful care of a responsible adult.
• Do not operate the machine while under the influence of drugs, alcohol, or any medication that could affect your ability to use it properly.
• Dress properly. Wear heavy long pants, boots, and gloves. Do not wear loose clothing, short pants, or jewelry of any kind. Secure long hair so it is above shoulder level. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. Protect eyes, face, and head from objects that may be thrown from the unit. Always wear safety goggles or safety glasses with side shields when operating.
• Wear appropriate hearing protection.
• Always keep hands and feet away from all moving parts during operation. Moving parts can cut or crush body parts.
• Always keep hands and feet away from all pinch points.
• Do not touch parts that might be hot from operation. Allow parts to cool before attempting to maintain, adjust, or service.
• Stay alert, watch what you are doing, and use common sense when operating the machine.
• Do not overreach. Do not operate the machine while barefoot or when wearing sandals or similar lightweight footwear. Wear protective footwear that will protect your feet and improve your footing on slippery surfaces. Keep proper footing and balance at all times. This enables better control of the machine in unexpected
• situations.

INSPECT YOUR MACHINE

• Check your machine before starting it. Keep guards in place and in working order. Make sure all nuts, bolts, etc., are securely tightened.
• Never operate the machine when it is in need of repair or is in poor mechanical condition. Replace damaged, missing, or failed parts before using it. Check for fuel leaks. Keep the machine in safe working condition.
• Do not use the machine if the engine’s switch does not turn it on or off. Any gasoline powered machine that can’t be controlled with the engine switch is dangerous and must be replaced.
• Regularly check to see that keys and adjusting wrenches are removed from the machine area before starting it. A wrench or a key that is left attached to a rotating part of the machine may result in personal injury.
• Avoid accidental starting. Be sure the engine’s switch is off before transporting the machine or performing any maintenance or service on the unit. Transporting or performing maintenance or service on a machine with its switch on invites accidents.
• If the machine should start to vibrate abnormally, stop the engine (motor) and check immediately for the cause. Vibration is generally a warning sign of trouble.

ENGINE SAFETY

• This machine is equipped with an internal combustion engine. Do not use on or near any unimproved, forest covered, or brush-covered land unless the exhaust system is equipped with a spark arrester meeting applicable local, state, or federal laws.
• Never start or run the engine inside a closed area. The exhaust fumes are dangerous, containing carbon monoxide, an odorless and deadly gas. Operate this unit only in a well-ventilated outdoor area.
• Do not tamper with the engine to run it at excessive speeds. The maximum engine speed is preset by the manufacturer and is within safety limits. See engine manual.
• Keep a Class B fire extinguisher on hand when operating this Wood chipper in dry areas as a precautionary measure.

FUEL SAFETY

• Fuel is highly flammable, and its vapors can explode if ignited. Take precautions when using to reduce the chance of serious personal injury.
• When refilling or draining the fuel tank, use an approved fuel storage container while in a clean, well-ventilated outdoor area. Do not smoke, or allow sparks, open flames, or other sources of ignition near the area while adding fuel or operating the unit. Never fill the fuel tank indoors.
• Keep grounded conductive objects, such as tools, away from exposed, live electrical parts and connections to avoid sparking or arcing. These events could ignite fumes or vapors.
• Always stop the engine and allow it to cool before filling the fuel tank. Never remove the cap of the fuel tank or add fuel while the engine is running or when the engine is hot. Do not operate the machine with known leaks in the fuel system.
• Loosen the fuel tank cap slowly to relieve any pressure in the tank.
• Never overfill the fuel tank. Fill the tank to no more than 1/2″ below the bottom of the filler neck to provide space for expansion as the heat of the engine can cause fuel to expand.
• Replace all fuel tank and container caps securely and wipe up spilled fuel. Never operate the unit without the fuel cap securely in place.
• Avoid creating a source of ignition for spilled fuel. If fuel is spilled, do not attempt to start the engine but move the machine away from the area of spillage and avoid creating any source of ignition until fuel vapors have dissipated.
• When fuel is spilled on yourself or your clothes, wash your skin and change clothes immediately.
• Store fuel in containers specifically designed and approved for this purpose.
• Store fuel in a cool, well-ventilated area, safely away from sparks, open flames, or other sources of ignition.
• Never store fuel or a machine with fuel in the tank inside a building where fumes may reach a spark, open flame, or any other source of ignition, such as a water heater, furnace, or clothes dryer. Allow the engine to cool before storing in any enclosure.

SPECIFIC SAFETY RULES

• Identify hazards and take preventive steps to avoid accidents and minimize risk. Possible hazards include, but are not limited to, moving parts, thrown objects, weight of the machine and components, and the operat-ing environment.

PRIOR TO STARTING

• Thoroughly inspect the area in which you are working, keeping it clean and free of debris to prevent tripping. Operate on a flat level ground.
• Before starting your chipper shredder: make sure the feed hopper and cutting housing are empty and free of all debris, check the oil level, make sure all nuts and bolts are tight, and check the air pressure in the tires.

OPERATION SAFETY

• Never place any part of your body where it would be in danger if movement should occur during assembly, installation, operation, maintenance, repair, or moving.
• Keep all bystanders and pets at least 75 feet away. If you are approached, stop the unit immediately.
• Never place your hands, feet, or any part of your body in the chipper hopper, discharge opening, or near or under any moving part while the machine is running. Keep the area of discharge clear of people, animals, buildings, glass, or anything else that will obstruct clear discharge, causing injury or damage. Wind can also change discharge direction, so be aware. If it becomes necessary to push materials to the chipper hopper, use a small-di-ameter stick, not your hands.
• Keep your face and body back from the chipper hopper and discharge chute to avoid injury from accidental bounce back of material.
• Never reach with your hands inside the feed hopper past the rubber flap while operating the machine.
• Keep combustible substances away from the engine when it is hot.

OPERATING ZONE

FEEDING MATERIALS

• Feed only clean materials into the machine. Foreign matter such as soil, sand, grit, stones, pieces of metal,etc. will damage the sharp edge of the cutting knives. Root balls and dead wood will also dull the blades quickly
• Avoid feeding pine needles, flax and cabbage tree leaves into the machine; these stringy materials can wrap around the rotor shaft and work their way into the bearing.
• Avoid feeding short, stubby pieces of wood into the machine; they tend to bounce and spin in the feed hopper.Feed these short pieces together with longer pieces. After becoming familiar with the machine,prune to suit its capabilities.
• This machine is self-feeding, do not force branches into the blades.Allow the machine to automatically feed through.Allow time for the machine to reach the highest spinning revolutions before feeding the next load of branches.

UNCLOGGING

• Never allow processed material to build up in the discharge area.This can prevent proper discharge and result in kickback from the chipper hopper.
• Never attempt to unclog either the feed hopper or discharge chute while the engine is running. Immediately shut off the engine,allow the cutting disk to come to a complete stop, and then remove the clogged material. Inspect for damage and check for any loose parts for repair or replacement.
• Whenever you leave the operating position or if you have to remove processed material, leaves, or debris from the machine, always shut down the engine, and ensure the engine is switched to”off” to prevent accidental starting, and wait for all moving parts to come to a complete stop.
• Before opening the cutting disk housing,always make sure the engine is switched off,the cutting disk is at a complete standstill, and the belt drive is disengaged.

MOVING

• Move the machine at least 10 feet away from the refuel-ing point before starting engine.
• This chipper shredder is for movement by hand only. Never attempt to tow the machine on public highways, roads,or thoroughfares.
• Always stop the engine before moving the machine, and watch out for sharp objects that could pierce the tires.

MACHINE USE AND CARE

• Position the machine in such a way that it can not move during maintenance,cleaning, adjustment, assembly of accessories or spare parts,as well as under storage
• Do not force the machine.Use the correct machine for your application. The correct machine will do the job better and safer at the rate for which it is designed.
• Do not change the engine governor settings or over-speed the engine. The governor controls the maximum safe operating speed of the engine.
• Do not run the engine at a high speed when youare not working.
• Do not put hands or feet near rotating parts.
• This machine has two rotating cutting knives capable of amputating hands and feet and throwing objects.Keep hands and feet out of openings while machine is running. Failure to observe these safety instructions could result in serious injury or death.
• Avoid contact with hot fuel, oil, exhaust fumes and hot surfaces.Do not touch the engine or muffler.These parts get extremely hot from operation. They remain hot for a short time after you turn off the unit.Allow the engine to cool before doing maintenance or making adjustments.
• If the machine should start to make an unusual noise or vibration,immediately shut off the engine, disconnect the spark plug wire,and check for the cause.Unusual noise or vibration is generally a warning of trouble.
• Use only attachments and accessories approved by the manufacturer. Failure to do so can result in personal injury.
• Keep the engine and muffler free of grass, leaves,exces-sive grease or carbon build up to reduce the chance of a fire hazard.
• Never douse or squirt the unit with water or any other liquid.Keep handles dry,clean and free from debris. Clean after each use.
• Observe proper disposal laws and regulations for gas,oil,etc. to protect the environment.
• When storing machine out of the reach of children and do not allow persons unfamiliar with the machine or these instructions to operate it. This machine can be dangerous when used by an untrained user.

MAINTAINING YOUR MACHINE

• Some parts of this machine are made of plastic or rubber and should be kept away from chemicals.
• Never cover the machine while the muffler is still hot.
• Do not alter or adjust any part of the chipper shredder or its engine that is sealed by the manufacturer or distributor. Only a qualified service technician may adjust parts that increase or decrease governed engine speed.
• To maintain your machine,check for any misalignment or binding of any moving parts. Parts that are broken or worn down that may affect the machine’s operation.If damage or worn parts are identify, they should be repaired before use. Many accidents are caused by poorly maintained equipment.

UNPACHING THE CONTAINER

Use scissors or a knife to cut and remove the straps. Remove the wooden plate in the top. At least two people hold up the package and move it from the top.

CONTENTS SUPPLIED
Your Wood chipper comes partially assembled and contains the following:

Verify all component and hardware quantities are correct prior to assembling the Wood chipper.

TO-SCALE HARDWARE

Hardware graphics are printed at 1:1 scale for ease of identification. Simply place the hardware over the image in the tables to verify it is the correct size.

ASSEMBLY

Axle
Attach the wheel axle to the cutter base with M14x140 hex bolts, flat washer 14 and M14 lock nuts.(See Figure 1

Wheels
Attach the wheels to the wheel axles with M10x25 he bolts,M10 lock nuts and flat washer 10(See Figure 2)

Tower bar mount
Attach the tower bar mount to the base frame with M12x35 hex bolts, Spring Washer 12 and flat washer 12 ( See Figure 3)

Tow bar and Guiding
wheel Attach the tow bar to the tower bar mounts with M10x70 hex bolts, M10 lock nuts and flat washer 10 (See Figure 4)

• Lower expulsion chute
  Attach the lower expulsion chute to the cutter base with two lock catches. (See Figure 5) Figure 5

• 360 degree upper expulsion chute
  Attach the upper expulsion chute to the lower expulsion chute with adjustable locking handle. (See Figure 6)

• Battery
  Attach the batterybox to the wheel axle with M10x80 hex bolts, M10 lock nuts and flat washer 10.(See Figure 7)

In-feeding chute

• Attach the feeding chute to the cutter base with two lock catches. (See Figure 8)

KNOW YOUR MACHINE

OPERATION

The engine is shipped without oil. Do not start the engine before adding oil.

ADD OIL TO ENGINE

1. Make sure the chipper shredder is on a flat, level surface.

2. Remove the oil fill cap/dipstick to add oil.

3. Using a funnel, add oil up to the FULL mark on the dipstick. (See engine manual for oil capacity, oil recom-mendation, and location of fill cap.).

DO NOT OVERFILL. Check engine oil level daily and add as needed.

ADD GASOLINE TO ENGINE
Gasoline is highly flammable and explosive. You can be burned or seriously injured when handling fuel. Use extreme care when handling gasoline
Fill the fuel tank outdoors, never indoors. Gasoline vapors can ignite if they collect inside an enclosure. Explosion can result.

1. The engine must be off and allowed to cool at least two minutes before adding fuel.

2. Remove the fuel filler cap and fill the tank. (See engine manual for fuel capacity, fuel recommendation, and location of fuel cap.)
   IMPORTANT:DO NOT OVERFILL!
   This equipment and/or its engine may include evaporative emissions control system components, required to meet EPA and/or CARB regulations, that will only function properly when the fuel tank has been filled to the recommended level. Overfilling may cause permanent damage to evaporative emissions control system components. Filling to the recommended level ensures a vapor gap required to allow for fuel expansion. Pay close atten-tion while filling the fuel tank to ensure that the recommended fuel level inside the tank is not exceeded. Use a portable gasoline container with an appropriately sized dispensing spout when filling the tank. Do not use a funnel or other device that obstructs the view of the tank filling process.

3. Reinstall the fuel cap and tighten. Always clean up spilled fuel.

STARTING ENGINE

1. Move the engine switch to the ON position.

2. Open the fuel shut-off valve.

3. Move the choke lever to the closed position.
   If the engine is hot, closing the choke is not necessary.

4. Move the throttle lever slightly to the FAST speed.

5. Pull the recoil starter until engine compression has become difficult to pull. Let the recoil return to the home  position, then pull quickly to start the engine. Repeat steps as needed. Fully open the choke and set the throttle  to the FAST position, before operating the unit.

Rapid retraction of the starter cord (kickback) will pull your handand arm toward the engine faster than you can let go.
Broken bones, fractures, bruises, or sprains could result.

OPERATING

After the engine warms up, pull the throttle lever to accelerate engine speed.
The chipper shredder can process a wide variety of dry or green organic materials such as branches, stalks, vines, leaves, roots, and vegetable matter. The maximum capacity is 6-inch diameter branches, this can vary depending on the type and hardness of wood. Rotating the branch as you feed it into the machine will improve performance.

• Feed limbs or branches through cut-end first, leaving the bushy head on. This helps guide the limb down the feed hopper and reduces spinning and bouncing of small pieces back up the feed hopper. Some side branches may require pre-cutting so that the branch will self-feed more efficiently.
• It is always advisable to process freshly cut materials, as wooden branches get very hard, they become springy when dried out and can make the knives dull more quickly.
• While operating the machine, keep a wooden stick handy, approximately 1 inch in diameter by 2 feet long. This stick will be useful to push in short, brushy and very leafy mate-rials and keep the feed hopper clear.
• Do not force material into the machine. If it does not chip well, the chipper knives may need sharpening or to be replaced, or the gap between the knives and the wear plate needs adjusting.
• Do not overload the machine by feeding too much material in to the feed hopper at one time. If you hear the speed of the engine decreasing, immediately stop feeding material in to the machine. Do not resume feeding material into the machine until the engine has returned to full speed.
• The wood chipper can clog up with soft, wet, or fibrous materials. However, if you feed soft materials intermittently with branches, there should be no problem, as the wood chipper tends to clean out any residue left in the machine.
• If any stringy material wraps around the rotor shaft, remove it before it works its way into the bearing.
• If the chipper shredder stalls from overloading or clogging, turn off the engine’s power switch and wait until the cutting disk is completely stopped and the belt drive is disengaged. Allow the engine to cool completely and switch the engine to off. Open the housing cover to clear and remove all the materials from the housing.
• Lock the housing cover, switch the engine to the on position, and start the machine again to resume operation.
• As the discharge material plies up, move the chipper away from the pile. This will keep the material from backing up the discharge chute. Do not position the deflector vertically, as this will reduce the airflow, impeding the discharge and causing blockage.
• Make sure the machine is level and stable to avoid unnecessary vibrations.
• Do not operate on concrete or other hard surface.
• Do not open the housing cover unless the engine and cutting disk are completely stopped and the belt drive is disengaged.
• The engine is fitted with an oil alert and will not start if the oil level in the sump is too low. It may also stop if it is operated on a steep slope.
• To shut down the machine, move the throttle control lever to idle speed, turn the engine switch to the OFF position, and it will gradually come to a standstill.

IDLE SPEED
Set the throttle control lever to the SLOW position to reduce stress on the engine when chipping is not being performed. Lowering the engine speed will help extend the life of the engine, as well as conserve fuel and reduce noise level.

STOP ENGINE
To stop the engine in an emergency, simply turn the engine switch to the OFF position. Under normal conditions, use the following procedure:

1. Move the throttle lever to the SLOW position.
2. Let the engine idle for one or two minutes.
3. Turn the engine switch to the OFF position.
4.  Turn the fuel valve lever to the OFF position.

• Sudden stopping at a high speed under a heavy load is not recommended. Engine damage may result.
• Do not move the choke control to CLOSE to stop the engine. Backfire or engine damage may occur.
• Wait until the machine completely stops. Allow the engine to completely cool. Then clean out the interior of the machine and its discharge chute.
• Do not disengage the belt drive with the machine running. This will cause friction and vibration on the belt drive.

TRANSPORTING
Your wood chipper is equipped with two large pneumatic wheels for easy movement by hand. To move the unit, grip the handles and tilt the wood chipper slightly after making sure the oil tank cover is tightened.

MAINTENANCE

Maintaining your Wood chipper will ensure long life to the machine and its components.

PREVENTIVE MAINTENANCE

1. Turn off the engine. The engine must be cool.
2. Keep the engine’s throttle lever in its SLOW position and remove the spark plug wire from the spark plug and secure.
3. Inspect the general condition of the chipper shredder. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, and any other condition that may affect its safe operation.
4. Remove all debris from the Wood chipper with a soft brush, vacuum, or compressed air. Then use a premium quality lightweight machine oil to lubricate all moving parts.
5.  Replace the spark plug wire.

Never use a pressure washer to clean your Wood chipper. Water can penetrate tight areas of the unit and cause damage to spindles, pulleys, bearings, or the engine.
Shut down the engine, wait for all moving parts to come to a complete stop, remove the spark plug wire, and then wait five minutes before performing maintenance on the chipper.

REGULAR MAINTENANCE CHECKLIST
The service intervals shown are the maximum under normal operating conditions. Increase frequencies under extremely dirty or dusty conditions.

There are two bearings, one outside and the other inside the housing . The bearings are greased when they are new, but it is recommended to grease them after a couple hours of use. One or two pumps is sufficient. Be careful not to over-grease. Over lubrication can damage the bearings.

Grease the outside bearing

1. Open the plastic oil plug.
2. Grease the outside bearing through the filling hole.
3. Close the plastic oil plug.

Grease the inside bearing

1. Loosen the lock nut which holds the discharge chute make chipping difficult for the operator. on the machine.
2. slide down the fixing plate under the lock nut.
3. Open , then grease the inside bearing

If the machine’s cutting disk strikes a foreign object, or if the machine begins to make an unusual noise or vibrates excessively, immediately shut off the engine. Allow the cutting disk to come to a complete stop. Switch the engine to “off” to avoid any accidental start. Then perform the following steps:

• Inspect for damage.
• Repair or replace damaged parts.
• Check for any loose parts and tighten to ensure continued safe operation.

KNIFE AND WEAR PLATE INSPECTION
Routine inspection of the knives for sharpness and wear plate for a sharp edge will ensure that your wood chipper is operating at full efficiency. Using dull knives or a round- ed wear plate will decrease performance and cause excessive vibration that will damage the machine and make chipping difficult for the operator.

KNIFE REMOVAL AND REPLACEMENT
This Wood chipper is equipped with two chipper knives mounted on the cutting disk. When the knives get dull or show visible nicks, the machine will lose its self- feeding action and the material has to be pushed in. Often it comes out in long strips. Replace the knifes by following steps.

1. Remove the feed hopper.
2.  Remove the discharge chute.
3. Rotate the cutting disc until the blade can be seen from the feed hopper side.
4. Remove the bolts, nuts that fix the blade.
5. Remove the dull or damaged knives and visually inspect the cutting disk slot and knives mounting area. Make sure they are clean and that the placement knives will be able to mount flush against the cutting disk. Remount new or sharpened knives with the knife edges facing up.

If the cutting disk surface is not cleaned properly and the knives are not mounted flush on the cutting disk, the knives could crack when the hardware is tightened.
The clearance between the knives and wear plate should be approximately 1 mm at the position of closest to the rotor shaft and 3 mm at the position of farthest to the rotor shaft. They are tapered out slightly to allow for a small amount of movement in the cutting disk as it bites into the wood. Make sure that all locknuts are tightened properly. Then turn the cutting disk with a long wooden stick to make sure it rotates freely.

BELT ADJUSTMENT
The belt on your chipper should deflect 3/8″ under three pounds of pressure as shown in fig. 1 below. If it doesn’t,- adjust per the following directions.

1. Remove belt guard.

2. Loosen engine bolts.

3. Tighten or loosen the nut until you have the correct tension as shown in fig. 1.

4. Retighten engine bolts.

5.  Check alignment of the clutch with the drive pulley by placing a straight edge across both faces as shown in fig.
   If adjustment is necessary, correct alignment by moving rotor pulley in or out on the rotor shaft. Do not make adjustment bymoving the clutch on the engine shaft.

6.  Replace belt guard.

BELT REPLACEMENT

1.  To replace the belt, follow the above belt adjustment directions.
2. After you have loosened the engine bolts, remove the old belts and replace it with new belts. Always replace both belts as they come in a matched set. This is required for proper operation
3. Set belt tension and alignment per above instructions.

NOTE: Check and re-tighten belts after initial break-in period, one hour of use.

CENTRIFUGAL CLUTCH TECH TIPS
THE SHOES AND SPRINGS ON THE CLUTCH ARE NORMAL WEAR ITEMS. IFYOU NOTICE DECREASED PERFORMANCE OF THE CLUTCH THEY SHOULDBE CHECKED AND REPLACED IF NECESSARY. The clutch on your machine is designed for rugged, dependable service, however, it is important to understand the limitations of a clutch. A clutch is designed to provide load free starting of the engine, and slippage under excessive overloading of the driven application. These features help protect the engine from damages such as broken crankshafts and starters. The clutch obtains its power from engine RPM’s. The lower the engagement speed, and the higher the main- tained engine speed, the more torque the clutch can transfer to the driven unit.Do not operate at less than full RPM’s. At engine start-up, the engine of your chipper operates under no load until approximately 1000-1200 RPM’S at which speed the centrifugal clutch engages and begins driving the rotor. Proper rotor speed is 2200 RPM +/ – 200 RPM when engine is at full RPM.

• At engine start-up, the engine of your chipper operates under no load until approximately 1000-1200 RPM’S at which speed the centrifugal clutch engages and begins driving the rotor.
• roper rotor speed is 2400 RPM +/ – 200 RPM when engine is at full RPM.
• Do not tamper with the engine’s governor setting. The governor controls the maximum safe operation speed and protects the engine.
• Over-speeding the engine is dangerous and will cause damage to the engine and to the other moving parts of the machine. See your authorized dealer for engine governor adjustments.
• Become familiar with successful operating conditions and avoid those that can overload and damage the machine.
• Do not overload or attempt to chip material beyond manufacturer’s recommendation.
• Personal injury or damage to the machine could result. Learn to recognize the sound of the machine when it is overloaded. If the machine becomes jammed by overload- ing or any other cause, stop the machine immediately. If you jam the machine and do not stop the engine, it can:
• Burn the belt.
• Ruin the clutch. Only your operator experience will tell you how fast you can successfully feed limbs into the machine. Clutch damage can be costly and damage is not covered under warranty. For this reason, it is important that you immediately shut off the machine if it becomes jammed.

STORAGE

If your Wood chipper will not be used for more than 30 days, follow the steps below to prepare your unit for storage:

1. drain the fuel tank completely. Stale fuel has high gum con tent and can clog the carburetor and restrict fuel flow.

2. Start the engine and allow it to run until it stops. This ensures no fuel is left in the carburetor and helps prevent deposits from forming inside, which can damage the engine

3. Drain the oil from the engine while it is still warm. Refill with fresh oil of the grade recommended in the engine manual

4. Allow the engine to cool. Remove the spark plug and put 60 ml of SAE-30 high-quality engine oil into the cylinder. Pull the starter rope slowly to distribute the oil. Replace the spark plug.
   Remove the spark plug and drain all oil from the cylinder before attempting to start the unit after storage.

5. Use clean cloths to clean off the outside of the Wood chipper and to keep the air vents free from obstructions.
   Do not use strong detergents or petroleum based cleaners when cleaning plastic parts. Chemicals can damage plastics.

6. Store your chipper shredder in an upright position in a clean, dry building with good ventilation. Do not store your chipper shredder with fuel in a non-ventilated area where fuel fumes could reach flames, sparks, pilot lights or any ignition sources. Use only approved fuel containers.

TROUBLESHOOTING

info@mechmaxx.com 13920 CITY CENTER DR.STE 235 CHINO HILLS, CA 91709, United States

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>