petsuper PW02 2-in-1 Intelligent Dog Training Collar Plus Bark Stopper Instruction Manual

petsuper PW02 2-in-1 Intelligent Dog Training Collar Plus Bark Stopper

Specifications

• Model: 2-in-1 Intelligent Dog Training Collar + Bark Stopper
• Dimensions (receiver): 78mm x 39mm x 33mm
• Weight (receiver): 80g – 50g
• Dimensions (remote control): 100mm x 50mm x 75mm
• Weight (remote control): 168g – 111g
• Battery Capacity: 300mAh – 400mAh
• Waterproof Rating: IP67

Product Usage Instructions

Bark Stopper (Receiver)

• Quick-release buckle Nylon strap
• Buckle
• Electrostatic nut (*Not provided for a non-electrostatic model)

Operation Instructions

• Antenna
• Digital display

Operation Instructions

FAQ

Q: How do I adjust the sensitivity and vibration levels?

A: By default, the product is set at Level 6 sensitivity and Level 3 vibration. Use the remote control to up-regulate or down-regulate the levels as needed.

Q: What is the recommended usage time for the product?

A: It is recommended not to use the product for more than 10 hours per day.

At first use

1. By default, the product is set at Level 6 sensitivity and Level 3 vibration.
2. Fully charge the product before first use. When the receiver is in standby mode, press “M” to check the charging status.

Warning

• It is recommended not to use the product for more than 10 hours per day.
• It is recommended that the dog should weigh from 5kg to 50kg, and its neck circumference should be smaller than 62cm. The product is not suitable fordogs lighter than 5kg or under 6 months old.
• The product is not a toy for children. Keep the bark stopper away from children to avoid injury.
• Do not use the product while charging.
• Tip: Please read the Instructions before use and use the product in a safe place!

Product List

Bark stopper (receiver)

Product introduction

Feature introduction

• The LED display light indicates the functions of the bark stopper. Press the “M” and “+” buttons to query about and promptly switch between different functions.
• Remote control: Press the corresponding function button and then press the “+” or “-” button to up-regulate or down-regulate the function.

Scientific training

(after the sound sensor detects a sound)

Operation instruction

Battery instructions

• I Low battery
• Battery Level
• F Training Cycle
• If the battery indicator displays “1” or “L”, fully charge the bark stopper before use.

Troubleshooting

If any abnormality of the product occurs during use, please check as follows:

• Make sure that the bark stopper is in close contact with the skin and not blocked by the hair.
• Up-regulate the sound sensitivity level.

Remote control

Quick start

• When the product is powered off, press and hold the “M” button for 3 seconds to light the display screen and all LED indicators, and then the buzzer will beep once and the product will vibrate once to indicate that it is powered on.
• After the product is powered on, both the display screen and LED indicators will be off.
• When the product is powered on, press “M” and then release it to display the battery power level.
• Continue to press and release “M” to display the sound sensitivity level.
• Continue to press and release “M” to display the vibration level.
• Continue to press and release “M” to display the electrostatic level.
• Each state will be displayed for 4 seconds.
• If no operation is performed within 4 seconds, the product will exit that state automatically.

Quick regulation

1. After the product is powered on, press the “+” button 3 times consecutively to make LED indicators flash, the buzzer beeps once and the product enters the mode.
2. Repeatedly press and release “M” to switch between sound sensitivity level, vibration level, and electrostatic level.
3. After the product is switched to the state to be regulated, press the “+” button to up-regulate the level.
4. Level 7 is the highest.
5. During electrostatic regulation, the electrostatic test board can be used to test if the bark stopper is live.
   • When the test indicator light is on, the bark stopper is live.

Screen off:

• The display screen will be off automatically if no operation is performed for 4 seconds.

Power off:

• In state setting mode, press and hold “M” for 3 seconds to power off the product, and all LED indicators will be off.

Caution

• Vocal cord position
• Don’t over-tighten the collar.
• Make sure that the dog does not act abnormally after the nut end makes contact with its
• Maximum circumference at a width of 15mm.

Recommended settings for the bark stopper

Caution: Please carefully read these Instructions before use.

Operating instructions for remote control: Power on/off

1. Press and hold the “On/off/manual/ auto” button of the remote control to power it on and light the display screen. Press and hold the button again to power it off. The display screen will be automatically off if no operation is performed for 8 seconds.
2. Charging: During charging, a red and flashing battery power indicator indicates that the remote control is being charged, and a green indicator indicates that it is fully charged.

Pairing between the remote control and the bark stopper (receiver):

1. Power on the bark stopper (receiver) and press the “+” button 3 consecutive times to make LED indicators flash, the buzzer beeps once and the bark stopper enters the state setting mode.
2. Press and hold the “+” button to make the buzzer beep once and the bark stopper enters the pairing mode.
3. Press and hold the “On/off/manual/auto” button of the remote control The display screen will be automatically off if no operation is performed for 8 seconds. Press and hold the button again to power off the remote control.
4. After the remote control is powered on, press the control switch button “CH” for successful pairing (one remote control can be paired with at most 3 bark stoppers (receivers).

Switch between bark stoppers (receivers):

1. After pairing, press the “On/off/manual/auto” button to switch between manual and auto modes. In auto mode, “M” on the display screen of the remote control is on. Press the button again to switch to manual mode, when “M” is off.
2. Among multiple bark stoppers (receivers) successfully paired, press the control switch button “CH” to switch among different bark stoppers (receivers) for regulation and use.

Cancel pairing and remote control of the bark stopper (receiver):

1. When the bark stopper (receiver) is powered on, press the “+” button 3 consecutive times to make LED indicators flash, the buzzer beeps once and the bark stopper enters the state setting mode.
2. Press again the “+” button 5 times consecutively to make the buzzer beep for 3 seconds to cancel pairing and remote control, and then the bark stopper restores to the initial function state.

Product specifications

Product name| 2-in-1 Intelligent Pet Training Collar| Waterproof rating| Bark stopper (receiver): IP67 Remote control: Non-waterproof
---|---|---|---
Product model| PA02| Working temperature| -10°C ~ 50°C
Working voltage| 3.7 V| Product dimension| Bark stopper (receiver):

78×39×33mm

Remote control: 144×49×19

Battery capacity| Bark stopper (receiver): 300mAh Remote control: 400mAh| Net weight| Bark stopper (receiver): 730g

Remote control: 50g

Rated input| DC5V/1A| Package dimension| Bark stopper (receiver): 100×50×75mm

Remote control: 168×111×50mm

Special cautions

• Do keep the nuts of the product at the dog’s throat, and do not use the product on the dog for more than 10 hours. Check every day the dog’s skin for allergies.
• The sensitivity of the sound sensor acts with dog barks. A low sound sensitivity level will cause the sound sensor to fail to detect dog barks. In that case, regulate the sound sensitivity level.
• It is recommended to impose electrostatic punishments only when it is necessary based on the physical and mental characteristics of the dog, and the intensity of electrostatic punishments should be up-regulated gradually.
• Do not use the bark stopper with a pet leash to avoid hurting the dog’s throat.

Scan the QR code for an instruction clip

FCC Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference,
2. this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>