Tripeak EMA-JW-OLPK30 Jetstream Pro Oversized Ceramic Bearings Installation Guide
- September 12, 2024
- TRiPEAK
Table of Contents
EMA-JW-OLPK30 Jetstream Pro Oversized Ceramic Bearings
“`html
Specifications:
-
Product Name: JETSTREAM PRO AXS ROAD
-
Compatible with: SRAM AXS 2S FORCE D-/2, SRAM AXS 2S RIVAL
D- -
Product Number: EMA-JW-OLPK30
Product Usage Instructions:
- Preparation:
– Secure the bike to a repair stand and remove the rear
wheel.
– Use a chain plier to remove the chain.
- Upper and Lower Pulley Maintenance:
– Remove upper and lower pulley caps of the AOPW.
– Apply one drop of TRiPEAK SUPRA LV Fluid to the bearing and
rotate to distribute.
– Reinstall the pulley caps without removing the seals.
- Replacing Pulleys:
– Use a hex or Torx wrench to remove the original upper
pulley.
– Replace with the AOPW upper pulley, ensuring correct
orientation.
– Install the AOPW lower pulley aligning the STOP PIN with the
cage position.
- Final Steps:
– Tighten AOPW pulley fixing screws to recommended torque
values.
– Reinstall the chain ensuring precise engagement with the
pulleys.
Frequently Asked Questions (FAQ):
- Q: Do I need to remove the seal on the pulley during
maintenance?
A: No, the SUPRA LV Fluid will seep into the
bearings through the gaps without seal removal.
- Q: How should I clean the bearings during
maintenance?
A: Use an appropriate solvent to thoroughly
clean the bearings and allow them to dry completely.
- Q: What is the recommended lubricant for bearing
maintenance?
A: TRiPEAK SUPRA LV Fluid is recommended for
bearing lubrication.
“`
JETSTREAM PRO
AXS
ROAD
INSTALLATION
¼ Compatible Rear Derailleur Models
SRAM AXS 2S FORCE D-/2 SRAM AXS 2S RIVAL D-
¼ Before installation, please ensure that the purchased pulley wheel meets the following specifications and includes the following contents.
Upper pulley caps
Both sides are the same ( 2 pcs )
Lower pulley cap
Inner side ( pc )
Lower pulley cap
Outer side ( pc )
Lubricating Grease
SUPRA LV Fluid
( bottle )
2T Upper pulley
( pc )
8T Lower pulley
( pc )
Force /
Rival
Product NO:EMA-JW-OLPK30
¼ Please follow the steps in this manual to install AOPW. If you lack the
necessary skills or experience, it is recommended to have the installation
done by a professional bike shop.
¼ After applying lubricant, the pulley wheel’s free-spinning performance may
not be as long-lasting as it was without lubricant. This is normal and does
not affect the rotational performance after installation.
¼ Do not alter this product in any way, as it can cause unseen damage. Any
modifications to this product will void the warranty.
¼ After installation, please recheck that all parts are securely installed and
that the operation is smooth and normal, ensuring riding safety.
¼ When cleaning the AOPW, use only mild soap and water. Never spray with high-
pressure water, as this may cause water ingress into the pulley bearings,
negatively affecting their rolling lifespan.
¼ If you have any questions or concerns about this product, Please feel free
to contact us. E-mail:info@tripeakbearing.com
Safety Glasses
Gloves
Bike Stand
PROTECTION SUPPLIES
Hex Key Set
Torx Key Set
Torque Wrench
Chain Plier
OPERATING TOOLS
Water-Based Cleaner
Lubricating Grease
Secure the bike to a repair stand, remove the rear wheel, use a chain plier to remove the chain.
Remove the upper and lower pulley caps of the AOPW. Apply one drop of TRiPEAK
SUPRA LV Fluid to the bearing, then rotate it to evenly distribute the
lubricant. Reinstall the pulley caps.
There’s no need to remove the seal on the pulley. Our SUPRA LV Fluid lubricant
will seep into the bearings through the gaps.
Use a hex or Torx wrench to remove the upper pulley from the original
derailleur (choose the tool based on the original screw specifications).
Replace it with the AOPW upper pulley (ensure the side with the text is facing
outward), and gently tighten the existing upper pulley screw.
Remove the lower pulley from the original derailleur. When installing the AOPW
lower pulley, align the STOP PIN on the pulley cap with the specified position
on the cage, as shown in the illustration. Once the lower pulley and cage are
properly aligned, reattach the fixing screw.
The installation position of the STOP PIN is on the inner plate.
Tighten the upper and lower AOPW pulley fixing screws to the torque value
recommended by the derailleur manufacturer.
Reinstall the chain on the bike, ensuring that the narrow-wide teeth of the
pulleys engage precisely with the chain’s gaps during installation.
JETST
12T
Upper pulley
STOP PIN
18T
Lower pulley
E A M PRO
JETSTR
Chain Narrow-Wide teeth
E A MPRO R
9 2X X R
¼ For maintaining and servicing Jetstream PRO AOPW, Please follow this manual,
or have it serviced by a professional bike shop.
¼ Regular maintenance is recommended every 6 months or after washing your
bike. If you ride in harsh conditions (wet, dusty, extreme temperatures,
etc.), it is advisable to perform maintenance immediately after your ride.
¼ The Jetstream PRO AOPW features an innovative design with non-replaceable
bearings. If the bearings have irreparable issues, the entire pulley wheel
should be replaced.
¼ Do not use high-pressure water jets to clean the AOPW to avoid water
infiltration and bearing damage.
¼ Regularly check the torque value of the fixing screws and ensure smooth
rotation. Never ride with a loose pulley wheel.
Use a small tool to gently pry off the seal from the pulley. Clean the
bearings thoroughly with an appropriate solvent to remove old lubricant and
debris. Allow them to dry completely.
Be cautious not to damage the seals or the bearings.
Apply one drop of TRiPEAK SUPRA LV Fluid to the bearing, then rotate it to
evenly distribute the lubricant.
ETSTREAM P
ETSTREAM P
O
J
R
O R
J
ETSTREAM P
ETSTREAM P
O R
J
RO
J
RO
J
ETSTREAM P
ETSTREAM P
O R
J
Carefully press the seal back onto the bearing, ensuring it is installed
properly and securely.
After reassembly, ensure the bearings move smoothly and freely.
JETSTREAM PRO
WWW.tripeakbearing.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>