TRIPEAK JETSTREAM PRO Asymmetric Oversize Pulley Wheel Installation Guide

September 11, 2024
TRiPEAK

TRIPEAK JETSTREAM PRO Asymmetric Oversize Pulley Wheel

Product Information

Product Specifications

  • Product Name: JETSTREAM PRO e-tap
  • Model: SRAM E-TAP S RED-A
  • Product Number: EMA-JW-OLPK30

Product Usage Instructions

Installation

  1. Secure the bike to a repair stand and remove the rear wheel.
  2. Use a chain plier to remove the chain.
  3. Remove upper and lower pulley caps of the AOPW.
  4. Apply one drop of TRiPEAK SUPRA LV Fluid to the bearing and rotate it for even distribution.
  5. Reinstall the pulley caps without removing the seal.
  6. Replace the upper pulley with the AOPW upper pulley and tighten the screw.
  7. Align the STOP PIN on the AOPW lower pulley cap with the specified position on the cage.
  8. Attach the fixing screw after aligning the lower pulley and cage.
  9. Tighten both upper and lower AOPW pulley fixing screws to recommended torque values.
  10. Reinstall the chain ensuring precise engagement with the pulleys’ narrow-wide teeth.

Maintenance

  1. Gently pry off the seal from the pulley for cleaning.
  2. Clean bearings thoroughly with an appropriate solvent and let them dry completely.
  3. Apply TRiPEAK SUPRA LV Fluid to the bearing and rotate for even distribution.
  4. Press the seal back onto the bearing carefully and securely.
  5. Ensure smooth movement of bearings after reassembly.

FAQ

  • Q: Do I need to remove the seals on the pulleys during maintenance?
    • A: No, you do not need to remove the seals. Our SUPRA LV Fluid lubricant will seep into the bearings through the gaps without seal removal.
  • Q: What should I use to clean the bearings?
    • A: Use an appropriate solvent to clean the bearings thoroughly, ensuring all old lubricant and debris are removed.
  • Q: How do I know if I’ve aligned the lower pulley and cage properly during installation?
    • A: Align the STOP PIN on the AOPW lower pulley cap with the specified position on the cage as shown in the illustration provided in the manual.

Specification

Specification Check

  • Compatible Rear Derailleur Models
    • SRAM E-TAP 11S RED-A1

Anatomy

Before installation, please ensure that the purchased pulley wheel meets the following specifications and includes the following contents.

General Safety

  • Please follow the steps in this manual to install AOPW. If you lack the necessary skills or experience, it is recommended to have the installation done by a professional bike shop.
  • After applying lubricant, the pulley wheel’s free-spinning performance may not be as long-lasting as it was without lubricant. This is normal and does not affect the rotational performance after installation.
  • Do not alter this product in any way, as it can cause unseen damage. Any modifications to this product will void the warranty.
  • After installation, please recheck that all parts are securely installed and that the operation is smooth and normal, ensuring riding safety.
  • When cleaning the AOPW, use only mild soap and water. Never spray with high-pressure water, as this may cause water ingress into the pulley bearings, negatively affecting their rolling lifespan.
  • If you have any questions or concerns about this product, Please feel free to contact us.

Required Tools

PROTECTION SUPPLIES

OPERATING TOOLS

Pulley Wheel Installation

  1. Secure the bike to a repair stand, remove the rear wheel, use a chain plier to remove the chain.
  2. Remove the upper and lower pulley caps of the AOPW. Apply one drop of TRiPEAK SUPRA LV Fluid to the bearing, then rotate it to evenly distribute the lubricant. Reinstall the pulley caps.
    • Warning: There’s no need to remove the seal on the pulley. Our SUPRA LV Fluid lubricant will seep into the bearings through the gaps.
  3. Use a hex or Torx wrench to remove the upper pulley from the original derailleur (choose the tool based on the original screw specifications). Replace it with the AOPW upper pulley, and gently tighten the existing upper pulley screw.
  4. Remove the lower pulley from the original derailleur. When installing the AOPW lower pulley, align the STOP PIN on the pulley cap with the specified position on the cage, as shown in the illustration. Once the lower pulley and cage are properly aligned, reattach the fixing screw.
  5. Tighten the upper and lower AOPW pulley fixing screws to the torque value recommended by the derailleur manufacturer.
  6. Reinstall the chain on the bike, ensuring that the narrow-wide teeth of the pulleys engage precisely with the chain’s gaps during installation.

Maintenance

  • For maintaining and servicing Jetstream PRO AOPW, Please follow this manual, or have it serviced by a professional bike shop.
  • Regular maintenance is recommended every 6 months or after washing your bike. If you ride in harsh conditions (wet, dusty, extreme temperatures, etc.), it is advisable to perform maintenance immediately after your ride.
  • The Jetstream PRO AOPW features an innovative design with non-replaceable bearings. If the bearings have irreparable issues, the entire pulley wheel should be replaced.
  • Do not use high-pressure water jets to clean the AOPW to avoid water infiltration and bearing damage.
  • Regularly check the torque value of the fixing screws and ensure smooth rotation. Never ride with a loose pulley wheel.

Reapply lubricant to pulley wheel

  1. Use a small tool to gently pry off the seal from the pulley. Clean the bearings thoroughly with an appropriate solvent to remove old lubricant and debris. Allow them to dry completely.
    • Warning: Be cautious not to damage the seals or the bearings.
  2. Apply one drop of TRiPEAK SUPRA LV Fluid to the bearing, then rotate it to evenly distribute the lubricant.
  3. Carefully press the seal back onto the bearing, ensuring it is installed properly and securely.
    • After reassembly, ensure the bearings move smoothly and freely.

www.tripeakbearing.com

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals