SENCOR SHT B360 TV Wall Mount Instruction Manual

SENCOR SHT B360 TV Wall Mount

Product Information

Specifications

• Model: SHT B360
• Components: A1 (4x), A2 (8x), A3 (8x), B (3x), C (3x), D (4x), E (4x), F (4x), G1 (4x), G2 (7x), G3 (4x), H (4x)
• Installation: Extension arms A2, A3, A1
• Screw Types: ST6.3×55, 10x6xL50, M4x14, M6x14, M8x20, D5/D6/D8, D8xH5
• VESA Compatible

Product Usage Instructions

Installation of Extension Arms
To install extension arms A2, A3, and A1, follow these steps:

1. Use screws ST6.3×55, 10x6xL50 to attach the extension arms securely.
2. Secure the arms using screws M4x14, M6x14, M8x20.
3. Ensure proper alignment of the arms with the designated slots.

Mounting Sequence
The mounting sequence for components B, G2, D/E/F, G, and H is as follows:

• Mount B first using the specified screws.
• Proceed to mount G2 next.
• Combine and mount D/E/F followed by G and H in sequence.

Frequently Asked Questions (FAQ)

• Q: Is this product compatible with VESA mounts?
  A: Yes, this product is VESA-compatible for mounting purposes.

IMPORTANT SAFETY INFORMATION

• Check the content of the package in parts list on page 2 and make sure that all parts are in order. Do not use damaged or faulty parts.
• Read all instructions before installing the equipment. When you are unsure about any part of the installation process, ask a professional technician for help.
• When tightening the screws, be careful to avoid stripping the thread.
• Do not install on a damp or otherwise damaged wall. The assembly material supplied in the package is designed to be mounted on a wall of bricks and concrete. For installation on walls made of other materials consult a professional.
• Never install or use this product if there are signs of damage.
• The edges of the equipment may cause injury if they are handled improperly.
• This device is not designed for assembly or handling by small children, or persons, who have not been specifically instructed unless supervised by a responsible person to ensure safety during handling or installation. Children should be supervised to ensure that they do not interfere with the equipment.
• Do not allow children to hang on the equipment or otherwise handle it. Otherwise, there is a danger of serious injury. Never insert your fingers or other objects into the mechanism of the equipment. It could cause personal injuries or property damage.
• The product contains small parts that can pose a choking hazard when inhaled or swallowed. Keep these parts out of reach of children!
  Note: Specifications and design are subject to change due to improvements without notice.

LIST OF SUPPLIED PARTS

• A. Holder
• B. Screw ST6.3×55
• C. Plastic anchor φ10xφ6xL50
• D. Screw M4×14
• E. Screw M6x14
• F. Screw M8×20
• G. Washer D5/D6/D8
• H. Spacer D8xH5

INSTALLATION

This TVG mount must be securely fastened to a vertical wall. If not solidly installed, it could fall and cause injury or damage.

Installing the mount on the wall of solid brick or concrete wall or panel
Mark the position of 3 holes on the wall for attaching the body of the holder. Use the holder A as a template (Fig. 1). Use masonry drill (10 mm) to pre- drill holes at least 9 cm deep and insert plastic anchor into each hole. C. Check that the plastic anchor is entirely inserted and even with the wallFig. 2 ). Attach the body of the holder to the wall using three screws B and washers G as shown in Fig. 3.

Mounting of bracket on TV set

TV set with flat rear wall (Fig. 4A)
First, find screws suitable for using to mount the TV set (D/E /F): try to screw them manually in the holes at the back of the TV set. If you feel resistance stop screwing in immediately! Once you find the screw with the correct threat proceed according to the drawing 4A. Insert washer on the screw (Gl) according to the picture. Then screw the screw in the bracket and finally in the TV set. Make sure that the bracket is attached vertically.

TV set with curved rear wall (Fig. 4B)
First, find screws suitable for using to mount the TV set (D/E/F): try to screw them manually in the holes at the back of the TV set. If you feel resistance stop screwing in immediately! Once you find the screw with the correct threat proceed according to the drawing 4B. Insert washer on the screw (Gl) and spacer(HI) in order corresponding to the picture. Then screw the screw into the bracket B and finally in the TV set. Check that the brackets are attached vertically and are parallel.

Attaching the TV set to the holder
Warning: Handling some TV sets requires help of another person. The manufacturer is not liable for injury or damage to property caused by improper handling!

Insert the TV set with the bracket on the body of the holder and tighten the locking screw thoroughly (fig. 6). Congratulation, the installation is done. We wish you a pleasant experience while watching TV mounted on the wall mount.

INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF USED PACKAGING
Take the used packaging material to the municipal waste disposal.

PRODUCT DISPOSAL AFTER END OF LIFE
Dispose of equipment after the end of life in the designated municipal solid waste place
This product meets all the basic requirements of EU directives that apply to it.

FAST CR, a. s.
Cernokostelecká 1621
251 01 Ricany
Czech Republic
www.stell-accessories.eu

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>