Marshall CV610-U2 Full HD USB 2.0 PTZ Camera User Manual

CV610-U2 Silver/Black
CV610-UB All Black
Full HD USB 2.0 PTZ Camera
Operating Instructions
Version V3.6

IMPORTANT SAFETY INSTRUCTIONS:

• Remove lens cover before plugging the camera into the power source.
•  Before starting operation, please fully read and follow all instructions in the manual. For your safety, always keep this manual with the camera for reference.
• The camera power input range is 100-240VAC (50-60Hz), ensure the power supply input is within this range before powering on.
• The camera power voltage is 12VDC, the rated currency is 1.5A. We suggest you use it with the original power supply adapter supplied in the box.
• Please keep the power cable, video cable and control cable in a safe place. Protect all cables especially the connectors from moisture and dirt.
• Operational environment: 32ºF to 122ºF ( 0ºC to 50ºC) and humidity less than 90%. To avoid any danger, do not put anything inside the camera, and keep away from corrosive liquids.
• Avoid stress, vibration, and jolts during transportation, storage, and installation.
• Do not detach the camera housing and cover. For any service, please contact authorized technicians.
• RF cable and control cable should be individually shielded, and cannot be substituted with other cables. Do not direct the camera lens towards strong light, such as the sun or the intensive light.
• Always use a dry, soft cloth to clean the camera housing. Only use neutral cleaning agents when there is need to clean smudges or dirt from the camera body. To avoid damage on the camera lens, only use a soft microfiber cloth.
• Do not carry or move the camera by holding the camera head. To avoid mechanical damage of internal gears, do not rotate the camera head by hand.
• Put the camera on a fixed desk or platform, avoid installing on surfaces that are not level.
• Power Supply Polarity (Drawing) below:

INCLUDED IN THE BOX

1. Power Adapter
2. CV610-U2-WM – Wall Mount
3. Power Cable
4. RS232 Control Cable
5. USB2.0 Cable
6. Remote Controller (battery not included)
7. Main Camera

QUICK START

1. REMOVE Lens Cover and check all cable connections to be sure they are all firmly connected before powering on
2. Dial Switch Setting (at the bottom of the camera):

DIP Switch (ARM)

| SW-1| SW-2| Instruction
1| OFF| OFF| Updating mode
2| ON| OFF| Debugging mode
3| OFF| ON| Undefined
4| ON| ON| Working mode

DIP Switch (IR CODE TYPE)

| SW-3| SW-4| Instruction
1| OFF| OFF| Off(Close IR receiver)
2| ON| OFF| Undefined
3| OFF| ON| SEJIN 4PPM CODE
4| ON| ON| NEC CODE(standard)

DIP Switch (USB)

| SW-5| SW-6| Instruction
1| OFF| OFF| Undefined
2| ON| OFF| Working mode
3| OFF| ON| Updating mode
4| ON| ON| Undefined

Note: Normal Working Mode: SW-1~5: ON, SW-6: OFF

PRODUCT HIGHLIGHTS

• Compact, ergonomically designed housing perfect for small huddle rooms or locations

•  Supports advanced Ambarella DSP, 1/2.8 inch 5MP image sensor, and high quality 10X 62.5 degree
  FOV optical lens, provides crystal clear image quality

• Fast switching between different video formats: less than 1 second

• 10X Optical Zoom + 12X Digital Zoom

• Fast and accurate focus performance

• Easy firmware upgrade – (field-upgradable)

• USB2.0 high-speed output

• Effective RS232/485 serial control. Up to 128 presets

• Compatible with the majority of videoconferencing software (UVC1.5 protocol standard)

• The camera comes with an accurate IR Remote Control unit

• IR transfer/IR pass function: excepts signals from other codec’s and IR remote control signals

CV610-U2 SPECIFICATIONS

RESOLUTION & FRAME RATE SETTINGS

The Marshall CV610-U2 acts as a UVC command slave to Teleconference, U.C. or Video Capture Software programs that use it as a USB capture device. Once selected as an available camera, these software platforms send commands to the camera as to compatible resolutions and frame rates based on bandwidth, software parameters, and/or computer capabilities. Some software platforms allow for direct adjust commands to change resolution and frame rates, such as VLC Player and others. CV610-U2 adjusts as commanded by the software platform or to the nearest resolution settings available (1080p, 720p, 480p). There is no way to manually adjust resolutions and frame rates from the camera or camera OSD menu since it relies on UVC (USB video class) commands. CV610-U2 adheres to UVC1.5 protocol standards.

CAMERA INTERFACE

1. Camera Lens
2.  Camera Base
3. IR Receiver Panel
4. Indicator Light
5. Dial Switch
6. Tripod Screw Hole
7. Installation Hole
8. RS232 (VISCA IN) Port
9. USB2.0 Port
10. DC12V Power Input
11.  Power Indicator light (red)

CAMERA DIMENSIONS (mm)

IR REMOTE CONTROLLER

LED Function Instruction
FOCUS
Press any button and shows in red color: Current selection is to control CAM1;
Press any button and shows in green color: Current selection is to control CAM2;
Press any button and shows in blue color: Current selection is to control CAM3;
CAM1/CAM2/CAM3:
Long press(3seconds) to set camera address;
Short press to select camera address to control.
Focus: +/-
Manual focus, only valid under manual focus mode;
Zoom: +/-
Control the lens zoom rate;
Navigate : Up/Down/Left/Right
In normal working mode, use navigate key to control pan/tilt；
Or enter the OSD menu, use navigate key to set parameters.
Confirm/Home button:
In normal working mode, short press to let the camera go back to the home position

Menu Button: Enter the OSD menu

Number buttons
Set Preset: Long press(3seconds) the number button to save preset;
Clear Preset: +number button to clear the relative preset;
Long press(3seconds) the Clear button to clear all preset;
Short press 3 times to reset the lens focus;
Run Preset: Short press the number button to run the relative preset.

Short press to power on or off the camera

CV610-U2 OSD MENU EXPLAINED

1. Once the camera is powered up and working, press the Menu button on the IR remote control to enter the OSD menu (see pic.1); once changes are made press the OSD menu button again to exit and save Modi ed parameters.
2. Use the navigation buttons (up/down/left/right) to choose which function to select. As picture 1 shows, once the selection is made, the selected option will change to a gray background highlight. Press the right navigation button to go to the submenu (see pic.2).
3. In the submenu, once again press the up/down navigation buttons to scroll and select, use the left/right navigation button to cycle through selection options parameters.
4. Select the last option “RETURN” and press the left navigation button to get back to the main menu or previous menu.
5. Press the OSD button again to exit the menu.
6. The following pages outline the Menu structure as it appears in OSD Menu:

(Valid when EXP MODE set to MANUAL or SHUT)
IRIS| Iris value: 0-13
(Valid when EXP MODE set to MANUAL or IRIS)
AGE| Gain value: 04B-15dB
(Valid when EXP MODE set to MANUAL)
BRIGHT| Brightness value: 0-27 (Valid when EXP MODE set to BRI.)
SLOW SHUT| OFF/ON
FLICK| OFF/50HZ/60HZ
(Valid when EXP MODE set to AUTO or IRIS)
RETURN| Back to the main menu
IMAGE
ENHANCE| 2D NR| OFF/ON
---|---|---
3D NR| OFF/AUTO/ 1-4
D_VVDR| OFF/1-6
GAMMA
0 -4|
BACKLIGHT| OFF/ON
HIGHLIGHT| OFF/ON
RETURN| Back to the main menu
MASK| MASK SWITCH| ON/OFF
---|---|---
COLOR| WHITE/YELLOW/GRAY/GREENNIOLET/RED
INDEX| 1-8
INDEX SWITCH| OFF/ON
ROW START| 0-1919
ROW END| 1-1920
LINE START| 0-1079
LINE END| 1-1079
RETURN| Back to the main menu
D/N MODE| D/N MODE| DAY/NIGHT/AUTO
---|---|---
DAY TO NIGHT| 15-126
NIGHT TO DAY| 5-190
SWITCH DELAY| 1-60
GAIN LIMIT| 2-511
RETURN| Back to the main menu
CAMERA
INFO| IMAGE VER.| PC-V0.0.6 (change without notice)
---|---|---
IMAGE DATE| 16.10.20 (change without notice)
CONTROL VER.| UC V0.1.4 (change without notice)
CONTROL DATE| 17.01.07 (changes without notice)
BAUDRATE| 9600
PARITY BIT| NONE
RETURN| Back to the main menu

1. All Button Sending Mode: long press (3seconds) the Menu+ number “3” button simultaneously, the remote will enter all button sending mode.
2. Similar operation for the TV control mode learning.

VISCA IN &RS485 Connection

Camera VISC| RS485
1| DTR|
2| DSR|
3| TXD|
4| GND|
5| RXD|
6| A(+)| TX+
7| IR OUT|
8| B(-)| TX-
VISCA IN 8089 Connection

Camera VISCA IN| Windows DB-9
1| DTR| 6| DSR
2| DSR| 4| DTR
3| TXD| 2| RXD
4| GND| 5| GND
5| RXD| 3| TXD
6| A(+)| |
7| IR OUT| |
8| 6(-)| |

SERIAL PORT CONFIGURATION:

VISCA PROTOCOL

Part 1 – Camera Return Command

Ack/Completion Message

| Command Packet| Note
ACK| z0 41 FF| Returned when the command is accepted.
Completion| z0 51 FF| Returned when the command has been executed.
Error Messages

| Command Packet| Note
Syntax Error| z0 60 02 FF| Returned when the command format is different or when a command with illegal  command parameters is accepted
Command Not
Executable| z0 61 41 FF| Returned when a command cannot be executed due to current conditions. For  example, when commands controlling the  focus manually are received during auto
focus.

Part 2 – Camera Control Command

-0x4000(tele))
CAM_Focus| Stop| 8x 01 04 08 00 FF|
Far(Standard)| 8x 01 04 08 02 FF
Near(Standard)| 8x 01 04 08 03 FF
Direct| 8x 01 04 48 Op Oa Or Os FF| pgrs: Focus Position
One Push AF| 8x 01 04 18 01 FF|
CAM_ZoomFocus| Direct| 8x 01 04 47 Op Oq Or Os Ot Ou Ov Ow FF| pqrs: Zoom Position (0(wide)- Ox4000(tete)) tuvw: Focus Position
CAMWB| Auto| 8x 01 04 35 00 FF|
Indoor| 8x 01 04 35 01 FF|
Outdoor| 8x 01 04 35 02 FF|
OnePush| 8x 01 04 35 03 FF|
Manual| 8x 01 04 35 05 FF|
Outdoor Auto| 8x 01 04 35 06 FF|
Sodium Lamp Auto| 8x 01 04 35 07 FF|
Sodium Auto| 8x 01 04 35 08 FF|
CAM_RGaln| Reset| 8x 01 04 03 00 FF| Manual Control of R Gain
Up| 8x 01 04 03 02 FF
Down| 8x 01 04 03 03 FF
Direct| 8x 01 04 43 00 00 Op Oq FF| pq: R Gain’ (0-0xFF)
Command| Fonnation| Command Packet| Note
---|---|---|---
CAMBgain| Reset| 8x 01 04 04 00 FF| Manual Control of B Gain
Up| 8x 01 04 04 02 FF|
Down| 8x 01 04 04 03 FF
Direct| 8x 01 04 44 00 00 Op Oq FF| pq: B Gain (0-0xFF)
CAM AE| Full Auto| 8x 01 04 39 00 FF| Automatic Exposure mode
Manual| 8x 01 04 39 03 FF| Manual Control mode
Bright| 8x 01 04 39 OD FF| Bright mode(Manual control)
CAM Shutter| Reset| 8x 01 04 OA 00 FF| Shutter Setting
Up| 8x 01 04 OA 02 FF|
Down| 8x 01 04 OA 03 FF|
Direct| 8x 01 04 4A 00 00 Op Oq FF| pq: Shutter Position (0-0x15)
CAM Iris
–| Reset| 8x 01 04 OB 00 FF| Iris Setting
Up| 8x 01 04 OB 02 FF
Down| 8x 01 04 OB 03 FF
Direct| 8x 01 04 4B 00 00 Op Oq FF| pq: Iris Position (0- Ox11)
CAM Gain
| Reset| 8x 01 04 OC 00 FF| Gain Setting
Up| 8x 01 04 OC 02 FF
Down| 8x 01 04 OC 03 FF
Direct| 8x 01 04 OC 00 00 Op Oq FF| pq: Gain Positon (0-0x0E)
CAM Bright| Reset| 8x 01 04 OD 00 FF| Bright Setting
Up| 8x 01 04 OD 02 FF
Down| 8x 01 04 OD 03 FF
Direct| 8x 01 04 4D 00 00 Op Oq FF| pq: Bright I Positon 0
CAM_WDR| On| 8x 01 04 3D 02 FF| WDR ON/OFF
OR| 8x 01 04 3D 03 FF
Direct| 8x 01 04 D3 Op FF| pq: WDR Position (1-0x06)
CAM Backlight| On| 8x 01 04 33 02 FF| BackLight On
OR| 8x 01 04 33 03 FF| BackLight OR
CAM_Aperture| Reset| 8x 01 04 02 00 FF| Aperture Control
Up| 8x 01 04 02 02 FF
Down| 8x 01 04 02 03 FF
Direct| 8x 01 04 42 00 00 Op Oq FF| pq: Aperture Gain (0-0x04)
CAM Memory| Reset| 8x 01 04 3F 00 Op FF| p: Memory Number (=0 to 127) Corresponds to 0 to 9 on the Remote Commander
Set| 8x 01 04 3F 01 Op FF
Recall| 8x 01 04 3F 02 Op FF
CAM_LR_Reverse| On| 8x 01 04 61 02 FF| Image Flip Horizontal ON/OFF
OR| 8x 01 04 61 03 FF
CAM_PictureFlip| On| 8x 01 04 66 02 FF| Image Flip Vertical ON/OFF
Off| 8x 01 04 66 03 FF
CAM_ColorGain| Direct| 8x 01 04 49 00 00 00 Op FF| (0-0x0E)
CAM_2D Noise Reduction| Direct| 8x 01 04 53 Op FF| 0::OFF 1:0N
Command| Funnation| Command Packet| Note
---|---|---|---
CAM_3D
Noise Reduction| Direct| 8x 01 04 54 Op FF| O:OFF 1: AUTO 2-5: LEVEL
FLICK| 50HZ| 81 01 04 23 01 FF|
60HZ| 81 01 04 23 02 FF
Freeze| Freeze On| 81 01 04 62 02 FF| Freeze On Immediately
Freeze Off| 81 01 04 62 03 FF| Freeze OR Immediately
Preset Freeze On| 81 01 04 62 22 FF| Freeze On When Running Preset
Preset Freeze OR| 81 01 04 62 23 FF| Freeze OR When Running Preset
IR_Transfer| Transfer On| 8x 01 06 1A 02 FF| Receive IR(remote commander) CODE from VISCA communication ON/OFF
Transfer Off| 8x 01 06 lA 03 FF|
Pan_tiltDrive| Up| 8x 01 06 01 VV WW 03 01 FF| W: Pan Weed 0z01 (low speed) to 0x 18 (high speed)
WW lilt speed Ox01 (low speed) to Ox14 (high speed)
YYVY: Pan Position(TBD)
ZZZZ. Tit Position(TBD)
Down| 8x 01 06 01 VV VVW 03 02 FF
Left| 8x 01 06 01 VV VVW 01 03 FF
Right| 8x 01 06 01 VV VIM 02 03 FF
Upleft| 8x 01 06 01 N/V WW 01 01 FF
Upright| 8x 01 06 01 N/V WW 02 01 FF
DownLeft| 8x 01 06 01 VV VVW 01 02 FF
DownRight| 8x 01 06 01 VV VVW 02 02 FF
Stop| 8x 01 06 01 W WW 03 03 FF
AbsolutePosition| 8x 01 06 02 W WW
OY OY OY OY OZ OZ OZ OZ FF
RelativePosition| 8x 01 06 03 W WW
OY OY OY OY OZ OZ OZ OZ FF
Home| 8x 01 06 04 FF
Reset| 8x 01 06 05 FF
Pan-tiltLimitSet| Set| 8x 01 06 07 00 OW
OY OY OY OY OZ OZ OZ OZ FF| W.1 UpRight 0:DownLeft
‘
YYVY: Pan Limit Position(TBD)
ZZZZ. Tilt Limit Position(TBD)
Clear| 8x 01 06 07 01 OW
07 OF OF OF 07 OF OF OF FF

Part 3 – Inquiry Command

y0 50 02 FF
Outdoor mode|
y0 50 03 FF| OnePush mode
y0 50 04 FF| ATW
y0 50 05 FF| Manual
CAM_RGainIng| 8x 09 04 43 FF| y0 50 00 00 Op Oq FF| pq: R Gain
CAM_BGalnIng| 8x 09 04 44 FF| y0 50 00 00 Op Oq FF| pq: B Gain
CAM_AEModelng| 8x 09 04 39 FF| y0 50 00 FF| Full Auto
y0 50 03 FF| Manual
y0 50 OA FF| Shutter priority
y0 50 OB FF| Iris priority
y0 50 OD FF| Bright
CAM_ShutterPosIng| 8x 09 04 4A FF| y0 50 00 00 Op Oq FF| pq: Shutter Position
CAM_IrisPosing| 8x 09 04 4B FF| y0 50 00 00 Op Oq FF| pq: Iris Position
CAMGainPosling| 8x 09 04 4C FF| y0 50 00 00 Op Oq FF| pq: Gain Position
CAM BrIghtPosfing| 8x 09 04 4D FF| y0 50 00 00 Op Oq FF| pq: Bright Position
CAM_ExpCompModelng| 8x 09 04 3E FF| y0 50 02 FF
On|
y0 50 03 FF| Off
CAM_ExpCompPosIng| 8x 09 04 4E FF| y0 50 00 00 Op Oq FF| pq: ExpComp Position
CAM_Apertureing| 8x 09 04 42 FF| y0 50 00 00 Op Oq FF| pq: Aperture Gain
CAM_MemoryIng| 8x 09 04 3F FF| y0 5Opp FF| pp: Memory number last operated.
SYS_MenuModelng| 8x 09 06 06 FF| y0 50 02 FF| On
y0 50 03 FF| Off
CAM_LR_ReverseIng| 8x 09 04 61 FF| y0 50 02 FF
On|
y0 50 03 FF| Off
CAM_PIctureFlIpIng| 8x 09 04 66 FF| y0 50 02 FF| On
y0 50 03 FF| Off
CAM_IDIng| 8x 09 04 22 FF| y0 50 Op Oq Or Os FF| pqrs: Camera ID
CAM_VerslonIng| 8x 09 00 02 FF| y0 50 ab cdmn pq rs to vw FF|
IR_Transter| 8x 09 06 1A FF| y050 02 FF
On|
y0 50 03 FF| Off
Pan411tMaxSpeedIng| 8x 09 06 11 FF| y0 50 ww zz FF| v: PanMaxSpeecl zz: lilt Max Speed
Pan4MPosIng| 8x 09 06 12 FF| y0 50 Ow Ow Ow Ow Oz Oz Oz Oz FF| %WON: PanPosition znz• Tilt Position

Note: (x) means the camera address; (y)=(x + 8).

Shutter
speed| | 60/30mode| 50/25mode| Iris| |
---|---|---|---|---|---|---
21| 1/10000| 1/10000| 0| close
20| 1/6000| 1/6000| 1| F14
19| 1/4000| 1/3500| 2| F11
18| 1/3000| 1/2500| 3| F0,10.
17| 1/2000| 1/1750| 4| F8
16| 1/1500| 1/1250| 5| F0,7.
15| 1/1000| 1/1000| 6| F0,6.
14| 1/725| 1/600| 7| F0,5.
13| 1/500| 1/425| 8| F4
12| 1/350| 1/300| 9| F0,3.
11| 1/250| 1/215| 10| F0,3.
10| 1/180| 1/150| 11| F0,2.
9| 1/125| 1/120| 12| F2
8| 1/100| 1/100| 13| F0,2.
7| 1/90| 1/75| |
6| 1/60| 1/50| |
5| 1/30| 1/25| |
4| 1/15| 1/12| |
3| 1/8| 1/6| |
2| 1/4| 1/3| |
1| 1/2| 1/2| |
0| 1/1| 1/1| |
Gain| 0| 0dB| | Gain| 8| 16dB
1| 2dB| | 9| 18dB
2| 4dB| | 10| 20dB
3| 6dB| | 11| 22dB
4| 8dB| | 12| 24dB
5| 10dB| | 13| 26dB
6| 12dB| | 14| 28dB
7| 14dB| | 15| 30dB

IR TRANSFER (IR PASS)

1. Currently the camera support NEC code format. For customization with other codes, please contact us.
2. Once the camera finish power configuration, enable the IR transfer function via sending COM command.
3. Get the targeted remote controller point to the camera IR receiver, press keys on the remote controller. then the camera will output the received IR code via the VISCA IN port.
4. IR Transfer output format: XX XX XX XX FF
   XX XX XX XX: Remote Controller Code| FF: End Code
   ---|---
5. The camera can save all settings, no need to re-set after the power circle.

UVC CONTROL

Wall Mount Installation

1. Secure the CV610-U2-WM to the wall with 4 M4 screws (included).
2. Disconnect all cables from the camera. Align the CV610-U2 camera’s ¼-20UNC tripod screw hole with the wall mount screw hole. Use the ¼-20UNC screw (included) to secure the camera onto the wall mount. Reconnect the cables after mounting the camera.
   Note: Do not mount the camera upside down, as the image will be displayed upside down.

Tel: 800-800-6608 / 310-333-0606 • Fax: 310-333-0688
www.marshall-usa.com
support@marshall-usa.com

References

• USA Location information - USA.com
• Marshall Electronics - Professional Broadcast Miniature/Compact/Indoor 4K/UHD/HD Cameras, 4K Rack Mount/Desktop Monitors, Hardware, and Accessories.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>